16.. what is used to determine when the communication channels are clear and when a device is free to transmit data?A. Carrier sense multiple access withcollision detection csma-cdB. Internet protocol IPC. Transmission control protocol TCPD. Ethernet

Technician B is correct. The transmission hydraulic pump operates when the engine is running, regardless of whether the vehicle is in motion or not.

The best automatic transmission fluids usually claim to improve vehicle fuel mileage, but renewing the fluid will almost always do that. ( Here are some other ways to improve your miles per gallon.) Technician A states that the transmission hydraulic pump operates only when the vehicle is in motion.

While Technician B says that the transmission hydraulic pump operates when the engine is running. In this case. Technician B is correct. The transmission hydraulic pump starts operating when the engine is running, as it is driven by the engine, regardless of whether the vehicle is in motion or not.

To know more about transmission hydraulic:- https://brainly.com/question/28429219

#SPJ11

Technician B is correct.

The transmission hydraulic pump operates when the engine is running, regardless of whether the vehicle is in motion or not. The pump is responsible for supplying pressurized hydraulic fluid to the transmission to engage the gears and provide torque to the wheels.

Learn more about transmission hydraulic: https://brainly.com/question/21634180

#SPJ11

The receiving device checks the Frame Check Sequence (FCS) field in the frame to ensure that the frame has not been corrupted during transmission.

The FCS field contains a mathematical checksum that is calculated by the transmitting device before the frame is sent. When the frame is received, the receiving device recalculates the checksum and compares it to the value in the FCS field.

If the two values match, the frame is considered error-free and is accepted. If the values do not match, the receiving device assumes that the frame has been corrupted during transmission and discards it.

Therefore, the FCS field is an important mechanism for ensuring the reliability of data transmission in a network.

A frame is transmitted from one networking device to another in a networking environment.

The receiving device checks the FCS (Frame Check Sequence) field in the frame to ensure data integrity and detect any possible errors that may have occurred during the transmission process.

The FCS is a type of error-detection mechanism that helps maintain the reliability and accuracy of the data being transmitted between devices.

By checking the FCS field, the receiving device can verify if the received frame is error-free or corrupted, and take appropriate action, such as requesting retransmission or discarding the frame.

Learn more about network click here:

brainly.com/question/14276789

#SPJ11

According to the National Electrical Code (NEC) section 310-10(H)(1), when conductors are installed in parallel is NO. 1/10 AWG.

According to the National Electrical Code (NEC) section 310-10(H)(1), when conductors are installed in parallel, they must be of the same length, have the same insulation and be terminated in the same manner at both ends.

Additionally, the minimum size of the phase, neutral or grounded conductor permitted for use in parallel is No. 1/0 AWG.

This minimum size requirement is based on the assumption that paralleling conductors will be used in large commercial or industrial applications where the electrical load is significant.

Using larger conductors helps to ensure that the load is distributed evenly across the conductors, minimizing voltage drop and improving the overall efficiency and safety of the electrical system.

Know more about the National Electrical Code (NEC)

https://brainly.com/question/20348027

#SPJ11

Where required for the reduction of electric noise for electronic equipment, electrical continuity of metal raceway is not required, and the metal raceway can terminate to a nonmetallic fitting or spacer on the electronic equipment.

Hi! In accordance with NEC 250-96(b), where required for the reduction of electric noise for electronic equipment, electrical continuity of metal raceway is not required, and the metal raceway can terminate to a nonmetallic fitting(s) or spacer on the electronic equipment.

According to NEC 250-96(b), where it is necessary to reduce electric noise for electronic equipment, electrical continuity of metal raceway is not required. In such cases, the metal raceway can terminate to a nonmetallic fitting or spacer on the electronic equipment. This helps to prevent the transfer of electrical noise from the raceway to the equipment, which can interfere with its proper functioning. Nonmetallic fittings or spacers are used because they do not conduct electricity and therefore do not provide a path for the noise to travel.

Learn more about electrical continuity here;

https://brainly.com/question/12791045

#SPJ11

According to NEC section 344.28, there should not be more than the equivalent of four quarter bends (or one full 90-degree bend) in a conduit run between pull points, which can include conduit bodies and boxes. This helps to ensure that the conduit run is not excessively curved or difficult to pull wire through.

This requirement is specified in the National Electrical Code (NEC) section 344.28.
Explanation:
1. A conduit is a tube or pipe used to protect and route electrical wiring.
2. Quarter bends refer to conduit bends, with each quarter bend equal to 90 degrees.
3. The term "equivalent" means having the same value or amount.

In this context, the equivalent of four quarter bends (4 x 90 degrees) adds up to a total of 360 degrees. To comply with the NEC requirement, the conduit run should not have bends exceeding this 360-degree limit between pull points, ensuring safe and efficient installation and maintenance of the electrical system.

To learn more about National Electric Code (NEC) : brainly.com/question/31389063

#SPJ11

A terminal that allows a server to enter guest orders but not settle guest accounts is called a  A. cashier terminal. Other types of terminals that may be used in hospitality settings include precheck terminals.

A terminal is a device or computer that allows a user to access a server or network. In the context of hospitality or restaurants, a terminal can be used by servers to input guest orders into a point-of-sale (POS) system, which is typically managed by a server.

In this scenario, the terminal is restricted to only allowing servers to enter guest orders and is not authorized to settle guest accounts. This is known as a "cashier" terminal, as it is only used for inputting orders and not handling payments or cash transactions.

Other types of terminals that may be used in hospitality settings include precheck terminals, which allow guests to view menus and place orders before being seated, and self-service terminals, which allow guests to place orders and pay without assistance from a server.

Learn more about  point-of-sale (POS) system here:

brainly.com/question/28198761

#SPJ11

"A terminal that allows a server to enter guest orders but not settle guest accounts is called a __________ terminal."

Your answer: A terminal that allows a server to enter guest orders but not settle guest accounts is called a B. precheck terminal.

Learn more about guest orders: https://brainly.com/question/1094377

#SPJ11

According to the National Electric Code (NEC) section 352-10(F), rigid nonmetallic conduit can be installed exposed in buildings where it is not subject to physical damage.

However, it is important to consult with local codes and damage before installing any electrical conduit to ensure compliance and safety.Rigid nonmetallic conduit (RNC) can be installed exposed in buildings when used in accordance with the National Electrical Code (NEC) Section 352-10(F). This section states that RNC is permitted for exposed work where it is not subject to physical damage, securely fastened, and properly supported.

Learn more about damage here

https://brainly.in/question/30120812

#SPJ11

The correct answer is c. Try block. In Java, to catch an exception that might be thrown by a block of code, that code must be enclosed in a try block.

A try block is followed by one or more catch blocks, which are used to catch and handle any exceptions that are thrown within the try block.

The basic syntax of a try-catch block in Java is as follows:

csharp

try {

   // code that might throw an exception

} catch (ExceptionType e) {

   // exception handler

}

The code that might throw an exception is enclosed in the try block. If an exception is thrown, the Java runtime system will search for a matching catch block to handle the exception.

The catch block specifies the type of exception it can handle, using the ExceptionType parameter. If the type of exception thrown matches the type specified in the catch block, the code within the catch block is executed to handle the exception.

In addition to try and catch blocks, Java also provides a finally block, which is used to specify code that should be executed regardless of whether an exception is thrown or caught.

The finally block is optional and is typically used for cleanup code that needs to be executed, such as closing a file or releasing a resource, regardless of whether an exception occurred or was caught.

In summary, to catch an exception in Java, the code that might throw the exception must be enclosed in a try block, followed by one or more catch blocks to handle the exception.

The finally block is optional and is used to specify code that should be executed regardless of whether an exception is thrown or caught.

Learn more about Java here:

https://brainly.com/question/29897053

#SPJ11

An asymmetric multiprocessing scheduler typically runs on the operating system kernel of the primary processing unit.

This scheduler is responsible for distributing tasks to the different processing units in the system, which may have varying capabilities and resource availability. The scheduler must take into account the workload and capabilities of each processing unit in order to optimize system performance and ensure that tasks are completed efficiently. Overall, the goal of the asymmetric multiprocessing scheduler is to maximize the utilization of available resources while minimizing delays and bottlenecks in the system.
An asymmetric multiprocessing scheduler runs on the master processor in an asymmetric multiprocessing system. This type of scheduler is responsible for managing tasks and resources across multiple processors, with the master processor handling the scheduling and coordination, while the other processors execute the assigned tasks.

To know more about operating system, click here:

https://brainly.com/question/30778007

#SPJ11

The interconnecting of timers is commonly called cascading. Option d is answer.

Cascading is the interconnection of timers in a way that allows one timer's output to trigger the start of another timer's countdown. This technique is often used in industrial automation systems to sequence events or processes that require precise timing. By cascading timers, it is possible to create complex timing sequences that are reliable and accurate.

This approach is particularly useful for applications where multiple timers need to work together in a coordinated manner to achieve a specific goal. Cascading timers is an effective way to simplify the programming and control of complex systems, as it allows for a more modular and scalable approach to timing control.

Option d is the answer.

You can learn more about timer at

https://brainly.com/question/29850873

#SPJ11

The number of 30-pin SIMMs installed in one bank can vary from 2 to 8, depending on the size of the individual SIMMs and the configuration of the memory bank.

72-pin SIMMs, the number of 30-pin SIMMs installed in one bank depends on the type of SIMM and the memory controller of the computer.

30-pin SIMMs were used in older computers, such as the first generations of Macintosh computers and some IBM PCs.

SIMMs typically came in sizes of 256KB, 512KB, 1MB, 2MB, 4MB, and 8MB.

A bank of memory using 256KB or 512KB SIMMs would typically have 8 slots, whereas banks of 1MB and 2MB SIMMs would have 4 slots.

Banks using 4MB and 8MB SIMMs would have 2 slots.

It is worth noting that 30-pin SIMMs are no longer commonly used in modern computers.

For similar questions on bank

https://brainly.com/question/14905714

#SPJ11

True.

The safety of maintenance personnel and electricians who may need to access the electrical equipment behind the panels.

Properly securing the wiring methods and equipment can prevent accidental contact with live conductors, reduce the risk of electrical hazards, and facilitate safe and efficient maintenance and repair of the electrical system.

This statement is in accordance with the requirements of the National Electrical Code (NEC) Article 300.23, specifies that wiring methods and equipment installed behind panels designed to permit access (such as drop ceilings) must be arranged and secured in such a way that panels can be removed to provide access to the electrical equipment.

According to the National Electrical Code (NEC) section 300.23, wiring methods and equipment installed behind panels designed to permit access, such as drop ceilings, must be arranged and secured in a manner that allows for the removal of panels to gain access to electrical equipment.

This requirement is necessary to ensure that maintenance and repair of electrical equipment can be safely performed without causing damage to the wiring or equipment.
Electrical equipment is installed behind panels designed for access, it is important to make sure that the panels are easily removable without causing any damage to the wiring or equipment.

This is achieved by properly securing the wiring and equipment to the structure using appropriate fasteners and support systems.

Additionally, the wiring and equipment should be arranged in a way that allows for easy access to all components without the need to remove any unnecessary materials or components.
The NEC requires that wiring methods and equipment installed behind panels designed for access be arranged and secured in a manner that allows for easy removal of panels to gain access to electrical equipment.

This requirement ensures that maintenance and repair of electrical equipment can be safely performed without causing damage to the wiring or equipment.

For similar questions on Equipment

https://brainly.com/question/30003482

#SPJ11

The load for house electric clothes dryers in a dwelling unit(s) shall be 5000 watts (volt-amps) or the nameplate rating, whichever is larger, for each dryer served.

This requirement can be found in section 220.54 of the National Electric Code. It is important to note that the nameplate rating of the dryer should always be taken into consideration when determining the load, as it may vary depending on the specific model and manufacturer.

The load for house electric clothes dryers in a dwelling unit(s) shall be 5,000 watts (volt-amps) or the nameplate rating, whichever is larger, for each dryer served. This is according to the National Electrical Code (NEC) section 220.54.

Learn more about NEC here:

brainly.com/question/28259564

#SPJ11

Foods that are fried in deep fat receive energy through conduction. The meal is uniformly cooked as a result of the hot oil heating the food's surface, which subsequently transfers heat to the centre.

Food is immersed in heated oil during the deep-frying process of cooking. The food's surface comes into touch with the heated oil when it is placed in the pan. Conduction is the method by which the heated oil conducts heat to the food's surface. Food is evenly cooked as a result of heat conduction from the surface to the centre of the food as it heats up. Conduction, which is the movement of heat through a solid or stationary fluid from a hotter location to a cooler region, is the term used to describe this heat transfer via the meal. As a result, the food receives energy from the heated oil, becoming crispy and delicious.

learn more about food's surface here:

https://brainly.com/question/16945643

#SPJ11

The correct statement regarding wake turbulence is: "The primary hazard is loss of control because of induced roll." Wake turbulence, caused by vortex generation, can pose a hazard to other aircraft, especially during takeoff and landing.

The induced roll from the wake turbulence can make it difficult for pilots to maintain control of their airplane. Vortex generation begins at rotation and continues as the airplane gains altitude. The primary hazard of wake turbulence is a loss of control due to induced roll, which can occur if an airplane encounters wake turbulence from a larger or heavier airplane. It is important for pilots to be aware of this hazard and take appropriate measures to avoid encountering wake turbulence.

Learn more about hazard here-

https://brainly.com/question/29602984

#SPJ11

No, In the context of a book, the terms "standards" and "protocols" do not mean the same thing.

Standards refer to established guidelines or criteria that are used to measure quality and consistency, whereas protocols are a set of rules or procedures that govern how actions are performed or how information is communicated. Both terms are important in different aspects of a book, but they serve distinct purposes.

So, the long answer is that although the terms "standards" and "protocols" may be used in similar contexts, they refer to different things and have distinct meanings.

Know more about the protocols

https://brainly.com/question/30547558

#SPJ11

The correct answer is (b) 6 degrees. A special engineering study is required for slopes with an incline greater than 6 degrees, as stated in the International Building Code (IBC) section 1612.3.

In civil engineering and construction, a slope refers to an inclined surface or ground. Slopes can be found in a variety of natural and man-made environments, including hillsides, road embankments, building sites, and retaining walls. The slope of a surface is typically measured in terms of its angle of inclination or its gradient. The angle of inclination is expressed in degrees, while the gradient is expressed as a percentage or a ratio. For example, a slope with a 10% gradient rises 10 units for every 100 units of horizontal distance. Slopes can pose various challenges and hazards, including erosion, landslides, and instability. For this reason, proper design and construction techniques are necessary to ensure the safety and stability of slopes, especially those located near buildings, roads, or other infrastructure. Special engineering studies may be required for slopes with steep inclines or other potentially hazardous conditions. These studies typically involve detailed analysis and testing to evaluate factors such as soil composition, water content, and stability, and to determine appropriate design measures and safety precautions.

Learn more about slopes here:

https://brainly.com/question/3944688

#SPJ11

B. import static java.lang.Math. it is important to use import static judiciously and only when necessary, as it can make code harder to read and understand if overused.

In Java, the import static keyword is used to import static members of a class into another class without having to reference the class name each time. This allows for more concise and readable code, especially when working with static utility classes like java.lang.Math. When using import static, you can directly reference the imported static members by their name, as if they were declared in the current class. For example, you could import the PI constant from java.lang.Math and use it in your code like this: double area = radius * radius * PI;. However, it is important to use import static judiciously and only when necessary, as it can make code harder to read and understand if overused.

Learn more about import static here:

https://brainly.com/question/23091646

#SPJ11

The collections framework algorithms are implementation-agnostic, i.e., each of these algorithms can operate on objects that offer given interfaces without concern to the underlying implementations.

This allows for flexibility and adaptability when working with different types of collections. The collections framework algorithms are interface-based, i.e., each of these algorithms can operate on objects that offer given interfaces without concern to the underlying implementations. This means that the algorithms are designed to work with any class that implements the required interface, regardless of how the class is implemented internally. This allows for greater flexibility and reusability of code within the collections framework.

Learn More about framework here :-

https://brainly.com/question/28991812

#SPJ11

The Life safety branch of the emergency system shall supply power for all of the following except non-emergency loads. Non-emergency loads include equipment and appliances that are not essential for life safety, such as lighting for non-essential areas, heating and cooling systems, and other non-essential equipment.

The Life safety branch is critical to ensure that essential life safety systems such as emergency lighting, fire alarms, and communication systems remain operational during an emergency or power outage. It is important to note that the Life safety branch must be designed and installed according to specific codes and standards to ensure its reliability and functionality.

Therefore, it is important to consult with a qualified electrical engineer or contractor to ensure compliance with the applicable regulations and guidelines.

Learn more about power here : brainly.in/question/1888377

#SPJ11

A data integrity problem will occur primarily when data are duplicated in a database.

Data integrity is the maintenance and assurance of data's accuracy and consistency over its entire lifecycle. When there is data duplication, it can lead to inconsistencies and incorrect information, which in turn negatively impacts the integrity of the database.

While having multiple administrators, a complex database, complex relationships between entities, and too many keys might pose management challenges, they are not the direct cause of data integrity problems. However, they can indirectly contribute to the issue if proper management practices are not followed.

In order to maintain data integrity, it is essential to implement measures such as data validation, normalization, and the use of primary keys to uniquely identify records. By doing so, it helps to minimize data duplication and ensures that the data remains consistent, accurate, and reliable throughout its lifecycle.

Learn more about Data integrity here: https://brainly.com/question/29455707

#SPJ11

Shale is the primary source rock for the vast majority of the world's oil and natural gas reserves.

A typical source rock of oil, which started out as mud in which dead organic matter settled, is shale. Shale is a sedimentary rock that is formed from the accumulation of clay and other fine-grained sedimentary particles. Over time, the accumulation of dead organic matter, such as plankton and algae, is buried by the sedimentary layers and undergoes a process of heat and pressure called diagenesis, which eventually transforms the organic matter into hydrocarbons such as oil and natural gas.

Learn more about rock here:

https://brainly.com/question/17137899

#SPJ11

The network administrator is trying to accommodate Quality of Service (QoS) and bandwidth management to give high priority to real-time applications traffic in the small business network.

The network administrator is trying to accommodate two types of network services: Quality of Service (QoS) and Traffic Shaping. QoS is a technique that prioritizes certain types of traffic over others, ensuring that real-time applications receive the bandwidth they require. Traffic shaping, on the other hand, manages the flow of traffic on the network, preventing congestion and ensuring that all applications receive the necessary bandwidth.

Learn More about Quality of Service here :-

https://brainly.com/question/15295852

#SPJ11

According to section 501.10 of the National Electrical Code, threaded rigid metal conduit or threaded steel must be used for the last 24 inches of an underground run to emergence. This is because these materials provide the necessary durability and strength to withstand the pressure and environmental factors that can impact underground electrical systems.

For such more question on installation

https://brainly.com/question/28452224

#SPJ11

The given statement "Some of the key factors in database design are content, access, structure, archiving, and security." is true because database design is the process of creating a database that is well-organized, efficient, and capable of meeting the needs of its users.

This refers to the type of data that will be stored in the database. It is important to identify the types of data, their relationships, and how they will be organized in the database. Database access involves determining who will have permission to view, edit, or delete data in the database.

This includes defining user roles and permissions, implementing access controls, and creating a user-friendly interface for accessing and manipulating data. This refers to the organization of data in the database, including the tables, fields, and relationships between them.

Learn more about database design: https://brainly.com/question/13266923

#SPJ11

True. 300-5(F) of the National Electric Code (NEC) specifies the requirements for backfill used for underground wiring.

According to this section, the backfill material used must not damage the wiring method, contribute to the corrosion of the raceway, or prevent compaction of the fill. This is important to ensure the long-term safety and reliability of the electrical system, as damage or corrosion to the wiring method can increase the risk of electrical hazards, such as shocks, fires, or explosions. By using an appropriate backfill material that meets the NEC requirements, the wiring method can be protected from damage and corrosion, and the overall safety and reliability of the electrical system can be maintained.

Learn more about underground wiring here:

https://brainly.com/question/27981910

#SPJ11

True. TW is a type of thermoplastic insulation that is suitable for use in both dry and wet locations. It has a maximum operating temperature of 60 degrees Celsius.

here is the list of several points to consider when choosing between thermoset and thermoplastic insulation:

Thermoset insulations have a higher tolerance to high temperatures compared to thermoplastic insulations. Thermoplastic insulations have a risk of heat deformation at inappropriately hot temperatures.

Thermoset insulations have superior flexibility, which they retain in cold temperatures. They stretch better than thermoplastic counterparts without the risk of breakage.

Thermoplastic materials are light in weight; therefore, thermoplastic insulations are a go-to when the weight matters. They can be put in very thin walls without negative consequences.

Thermoplastic insulations are easier to produce, which makes them cheaper than thermoset analogs.

Thermoplastic insulations are recyclable, while thermoset insulations cannot be recycled.

Thermoset insulations are quite hard and rigid, which can be a pro or a con depending on the particular electrical application.

learn more about thermoplastic insulation here:

https://brainly.com/question/29596428

#SPJ11

Answer:

c.certification

Explanation:

hope this helps!

A tsunami watch is issued by the Pacific Tsunami Warning Center when a large earthquake occurs in the Pacific Ocean that has the potential to generate a tsunami. They detect an earthquake or other event that has the potential to generate a tsunami in the Pacific Ocean.

The watch is issued as a precautionary measure to alert coastal communities to the possibility of a tsunami and to encourage them to prepare for the worst-case scenario. The warning center monitors seismic activity and sea level readings to determine the likelihood of a tsunami and will issue a warning if there is a high probability of a tsunami reaching the coastline. It is important to take tsunami watches and warnings seriously and follow evacuation orders to ensure the safety of yourself and others.
The watch is issued to alert affected coastal regions and help them prepare for a possible tsunami, allowing residents and officials to take necessary precautions and monitor the situation closely.

Learn more about seismic activity here:

brainly.com/question/30667043

#SPJ11

A tsunami watch is issued by the Pacific Tsunami Warning Center when there is a possibility of a tsunami occurring in the Pacific Ocean, usually due to an earthquake or other seismic event.

Tsunamis are massive waves that result from seismic activity or volcanic eruptions beneath the ocean. When formed in the open sea, the height of the waves remains relatively constant. However, as the waves approach the shore, they gather momentum and grow taller due to the decreasing depth of the water.

This watch serves as an early warning to coastal areas, allowing them to prepare for a potential tsunami.

Learn more about Tsunamis: https://brainly.com/question/11687903

#SPJ11

On a wing, the force of lift acts perpendicular to the relative wind and the force of drag acts parallel to the flightpath. Option b is answer.

The chord line is an imaginary straight line that connects the leading edge to the trailing edge of the wing and the longitudinal axis is an imaginary line that runs through the center of the airplane from nose to tail. The force of lift is generated due to the difference in air pressure on the top and bottom surfaces of the wing, and it acts perpendicular to the relative wind, which is the direction of the airflow relative to the wing.

The force of drag, on the other hand, is generated due to the resistance of the air to the motion of the airplane through it, and it acts parallel to the flightpath of the airplane.

Option b is answer.

You can learn more about flightpath at

https://brainly.com/question/29119301

#SPJ11