(a) The estimate of the definite integral using the Midpoint Rule with m = n = 2 is 1952
(b) The estimate of the average value of f is 30.5.
The Midpoint Rule formula for approximating the definite integral is:
∫∫f(x,y)dA ≈ (A/mn) ∑∑f(x_i, y_j) where,
A is the area of the squarem and n are the numbers of sub-rectangles in the x and y directions respectivelyx_i and y_j are the midpoints of the sub-rectanglesf(x_i, y_j) is the function evaluated at the midpoint of the sub-rectangle.In this case, A = 64, m = n = 2. So we can compute the function value at the midpoint of each sub-rectangle and multiply it by the area of the sub-rectangle. The midpoints of the sub-rectangles are located at (2,2), (2,6), (6,2), and (6,6).
∫∫f(x,y)dA ≈ (64/4) [ f(2,2) + f(2,6) + f(6,2) + f(6,6) ] = (64/4) [ 1952 ] = 1952
(a) Use the Midpoint Rule with m = n = 2 to estimate the value of f(x,y) dA. R (Round your answer to the nearest integer.) 1952
(b) (1/A) ∫∫f(x,y)dA
So in this case it would be (1/64) * 1952 = 30.5
Estimate the average value of f. (Round your answer to one decimal place.) 30.5
Therefore, the estimate of the definite integral using the Midpoint Rule with m = n = 2 is 1952, and the estimate of the average value of f is 30.5.
Learn more about the Midpoint Rule here:
https://brainly.com/question/30079030
#SPJ4
8
unit 1
Which of the following best describes on ston
protons, neutrons, and elections all in the cont
B. a core of negatively and positely chared parts
Surrounded by nextral particles
c. a core
surrounded
of positive and neatral particles
by negative particles
D. acore of elections and neations surtou
by protons.
Answer: C.
Explanation: The core or Nucleus of an atom contains Protons and Neutrons. A proton has a +1 charge while a Neutron is a Neutral or 0 charge. Electrons orbit the Nucleus and have a -1 charge.
Daniel scores 68,84,76 and 80 in four test. what mark should he score in the fifth test so that his average mark for the five test would be 78.
(I) what was his median score in the five test
Answer
68+84+76+80+x / 5 =78
x= it is value of his result in 5th test
x=82
Explanation:
Then you put all value from smallest to the biggest
68,76,80,82,84
median = 80
Germicidal lamps are used to sterilize tools in biological and medical facilities. One type of germicidal lamp is a low-pressure mercury discharge tube, similar to a fluorescent lightbulb, that has been optimized to emit ultraviolet light with a wavelength of 254 nm. A 15-mm-diameter, 25-cm-long tube emits 4.5 W of ultraviolet light. The mercury vapor pressure inside the tube is 1.0 Pa at the operating temperature of 40?C.
Part A
On average, how many ultraviolet photons does each mercury atom emit per second?
Express your answer using two significant figures.
Part B
The lifetime of the excited state in mercury is a rather long 120 ns. On average, how much time does a mercury atom spend in the excited state?
Express your answer to two significant figures and include the appropriate units.
Answer of part A and Part B is given below.
What is wavelength?Wavelength is a measure of the distance between two successive crests or troughs on a wave. It is measured in the same physical units as the length, such as meters (m) or feet (ft). Wavelength is most commonly used to describe light waves, but it can also be applied to sound waves, water waves, and other types of waves. Wavelength is inversely related to the frequency of a wave, meaning that waves with shorter wavelengths have higher frequencies. In optics, the term "wavelength" is used to describe the frequency of visible light, which ranges from 380 to 780 nanometers.
Part A
On average, each mercury atom emits 6.2x10^7 ultraviolet photons per second.
Part B
The average time that a mercury atom spends in the excited state is 12 µs.
To know more about wavelentgh click-
https://brainly.com/question/10728818
#SPJ4
Aluminum wire #1 has a length L and diameter d. Aluminum wire #2 has length 3L and diameter 3d. What statement about resistances of these wires is correct? O The resistance of wire #1 is three times the resistance of wire #2 O Resistance of wire #1 is 9 times resistance of wire #2. O The resistance of wire #1 is the same as the resistance of wire #2 O The resistance of wire #1 is 1/9 of the resistance of wire #2 O Resistance of wire #1 is 1/3 of resistance of wire #2.
The resistance of wire one is three times of resistance of wire 2. The correct option is (a).
The resistance of a wire is directly proportional to length (L) and inversely proportional to the cross-sectional area.
For wire 1:
R₁ = k ×L ÷(π × (d÷2)²)
Here,
Diameter (d) and constant (k).
For wire 2:
R₂ = k × 3L ÷ (× ((3d)÷2)²)
R₂ = (1/3) × k ×L ÷(π × (d÷2)²)
R₂ = 1÷ 3R₁
R₁ = 3R₂
Hence, The resistance of wire one is three times of resistance of wire 2. The correct option is (a).
To learn more about Resistance, here :
https://brainly.com/question/29427458
#SPJ12
. Johnathan road his bicycle up a hill at a velocity of 17.15 m/s. Johnathan and his bicycle had
a combined mass of 88 kg. What was the height of the hill?
The height of the hill is 15 m.
What is the height of the hill?
The height of the hill is calculated by applying the principle of conservation of energy as shown below.
Kinetic energy at the bottom of the hill = Potential energy at the top of the hill
mgh = ¹/₂mv²
gh = ¹/₂v²
h = ( v² ) / ( 2g )
where;
v is the velocity of Johnathang is acceleration due to gravityh = ( v² ) / ( 2g )
h = ( 17.15² ) / ( 2 x 9.8 )
h = 15 m
Learn more about Height of hill here: https://brainly.com/question/24219606
#SPJ1
Read the passage.
At the sound of the gun, the runners' legs began to
cross the starting line in a blur, and their bodies surged
forward as if propelled by unseen engines. The lanes
were runways, and the runners could take flight at any
moment. But they stayed on earth, their feet drumming
the ground in an uneven staccato that reverberated in
the chests of the cheering crowd that choked the fence
along the track.
Which statement best describes the use of diction in
this passage?
O The author uses several words with negative
connotations.
O The author uses a variety of specific and interesting
verbs.
O The author uses a number of words that are
informal.
O The author uses a variety of specific and unusual
adjectives.
The author uses a variety of specific and interesting verbs, 2nd option.
What is a diction?Diction refers to the choice and use of words in speech or writing. It can also refer to the style or manner of speaking or writing, including the level of formality, the choice of vocabulary, and the grammatical structures used. In literature, diction is an important aspect of a writer's style, and can be used to create a certain tone or atmosphere in a text.
Formal diction, slang diction, informal diction, concrete diction, colloquial diction, and abstract diction are all examples of diction. A good diction should have words that are accurate and easy to understand. The writer used interesting verbs like "surged" and "choked' in "choked the fence" etc.
Find out more on diction here: https://brainly.com/question/1503891
#SPJ1
Answer:
B
Explanation:
The normal force R that a car makes with the ground is 5000N. What is the maximum force of static friction that the car's wheels can experience with the flat concrete road? What is the force of friction that the wheels experience when the car is moving?
The maximum force of static friction that the car's wheels can experience with the flat concrete road is μ×5000 N.
The force of friction that the wheels experience when the car is moving is less than maximum force of static friction.
What is static friction?
The definition of static friction is: The resistance people feel when they attempt to move a stationary object across a surface without actually causing any relative motion between their body and the surface they are moving the object across.
As the normal force = 5000 N.
The maximum force of static friction = μ×5000 N.
The force of friction that the wheels experience when the car is moving is less than maximum force of static friction.
Learn more about static friction here:
https://brainly.com/question/13000653
#SPJ1
A typical laboratory diffraction grating has 5500 lines/cm , and these lines are contained in a 4.00 cm width of grating. a.What is the chromatic resolving power of such a grating in the first order? b.Could this grating resolve the lines of the sodium doublet (λ1 = 589.00nm, λ2 = 589.59nm ) in the first order?
c.While doing spectral analysis of a star, you are using this grating in the second order to resolve spectral lines that are very close to the 587.8002-nmspectral line of iron. For wavelengths longer than the iron line, what is the shortest wavelength you could distinguish from the iron line? d.For wavelengths shorter than the iron line, what is the longest wavelength you could distinguish from the iron line? e.What is the range of wavelengths you could not distinguish from the iron line?(Values of λshorter and λlonger you have calculated in two previous parts.)
a. The chromatic resolving power of such a grating in the first order is 1.8 x 10^-6 cm.
b. This grating resolve the lines of the sodium doublet (λ1 = 589.00nm, λ2 = 589.59nm ) in the first order cannot resolve the lines of the sodium doublet in the first order.
c. The shortest wavelength you could distinguish from the iron line is 587.8
d. The longest wavelength you could distinguish from the iron line is 587.8
e. The range of wavelengths you could not distinguish from the iron line?(Values of λshorter and λlonger you have calculated in two previous parts.) is 587.8002 - 587.8)nm to (587.8 - 587.8002)nm.
How do you arrive at the values given above?a. The chromatic resolving power of a diffraction grating is given by the formula: R = mλ/Δλ, where m is the order of diffraction, λ is the wavelength, and Δλ is the minimum separation of two wavelengths that can be resolved. In the first order, m = 1. Therefore, the chromatic resolving power is R = mλ/Δλ = 1 * (1/5500 cm) = 1.8 x 10^-6 cm.
b. To determine if the grating can resolve the lines of the sodium doublet, we need to compare the separation of the doublet lines (589.59nm - 589.00nm = 0.59nm) to the chromatic resolving power of the grating. If the separation is greater than the resolving power, the lines can be resolved. The resolving power is 1.8 x 10^-6 cm, which is equivalent to 1.8 x 10^-9 m. The separation of the doublet lines is 0.59 x 10^-9 m, which is less than the resolving power, so this grating cannot resolve the lines of the sodium doublet in the first order.
c. In the second order, m=2, the shortest wavelength that can be distinguished from the 587.8002 nm line of iron is 587.8002 nm - (1.8 x 10^-6 cm) = 587.8002 nm - (1.8 x 10^-9 m) = 587.8002 nm - 0.00000000018 m = 587.8002 - 0.000000018 m = 587.8.
d. In the second order, m=2, the longest wavelength that can be distinguished from the 587.8002 nm line of iron is 587.8002 nm + (1.8 x 10^-6 cm) = 587.8002 nm + (1.8 x 10^-9 m) = 587.8002 nm + 0.00000000018 m = 587.8002 + 0.000000018 m = 587.8.
e. The range of wavelengths that cannot be distinguished from the iron line of 587.8002 nm is from (587.8002 - 587.8)nm to (587.8 - 587.8002)nm.
Therefore, the correct answers are as given above
learn more about chromatic resolving power: https://brainly.com/question/29762123
#SPJ1
the figure (figure 1) is an energy-level diagram for a simple atom.
The diagram shows the possible energy levels that an atom can occupy. The atom is assumed to have two electrons, shown by the two distinct circles.
What is atom?
Atom is a free and open-source text editor created by GitHub that works on the three major operating systems; Windows, Mac and Linux. It is a highly customizable text editor that can be used for coding, writing and editing. It offers a wide range of features such as syntax highlighting, multi-cursor editing, automatic indentation, and auto-completion.
There are two main energy levels, the ground state and the excited state. The ground state is the lowest energy level, and the excited state is the highest energy level that the atom can occupy. In between these two levels are the intermediate energy states, which the electrons can transition between.
To learn more about atom
https://brainly.com/question/621740
#SPJ4
What part of the sweating process promotes cooling?
wiping sweat from the surface of the skin
condensation of liquid sweat on the skin
liquid (sweat) sitting on the skin’s surface
evaporation of liquid sweat from the skin
Answer: Condensation of liquid sweat on the skin
Explanation:
A 3.00-kg ball rests in a frictionless groove as shown in the figure
(a) What is the magnitude of the force that the left side of the groove exerts on the ball?
(b) What is the magnitude of the force that the right side of the groove exerts on the ball?
Answer: (a) 26.4 N (b) 21.5 N
(a) Magnitude of the force that the left side of the groove exerts on the ball is 26.4 N. (b) Magnitude of the force that the right side of the groove exerts on the ball is 21.5 N.
(a) Magnitude of the force that the left side of the groove exerts on the ball:
The centripetal force (Fc) required to keep the ball moving in a circle can be calculated using the equation:
Fc = (m × v²) / r
m × g × h = (1/2) × m × v²
v² = (2 × g × h)
v² = 2 × 9.81 × 1.20
v² = 23.55
v = √(23.55)
v = 4.854 m/s
Now, we can find the centripetal force (Fc):
Fc = (3.00 × (4.854)²) / 1.40
Fc = 26.4 N
(b) Magnitude of the force that the right side of the groove exerts on the ball:
Weight of the ball (Fg) = m × g
Fg = 3.00 × 9.81 m/s² = 21.5 N
So, the magnitude of the force that the right side of the groove exerts on the ball (the normal force) is approximately 21.5 N.
To know more about the force:
https://brainly.com/question/13191643
#SPJ12
Can nuclei of the same element have different values of Z? Of N? Of A?
Check all that apply.
1 Nuclei of the same element must have the same values of Z, N, and A.
2 Nuclei of the same element can have different values of Z.3
3 Nuclei of the same element can have different values of A.
4 Nuclei of the same element can have different values of N.
Can nuclei of different elements have the same values of Z? Of N? Of A?
Check all that apply.
1 Nuclei of the same element can have the same values of Z.
2 Nuclei of the same element must have different values of Z, N, and A.
3 Nuclei of the same element can have the same values of N.
4 Nuclei of the same element can have the same values of A.
Nuclei of the same element can have different values of A and Nuclei of the same element can have different values of N and Nuclei of the different elements can have the same values of A.
Who is the founded of atomic nucleus ?On the basis of the 1909 Geiger-Marsden gold foil experiment, Ernest Rutherford identified the atomic nucleus in 1911, which is the compact, dense region made up of protons and neutrons at the heart of an atom.
There are 118 species of atoms listed in the periodic table of elements, and each of these can be found (either naturally or artificially) in several iterations with various neutron counts, leading to a total of around 3,000 distinct atomic nuclei.
Both nuclei are held together by the electron, which "orbits" them. We have a molecular ion because the total charge is undoubtedly non-zero. According to Wikipedia, this system is referred to as the dihydrogen cation and goes by the symbol H+2.
the solution is
The proton ratio (Z) for a particular element is fixed. The mass number can vary depending on the number of neutrons (N) in the same element and other elements (A).
Atoms having the same Z and different N (and hence different A) are called isotopes. They are usually forms of the same element.
Sometimes atoms of different element can have the same mass number (A) but different atomic number (Z) and neutron number (N) that makes up the same mass number (A). They are called isobars
Also,atoms of different element can have the same neutron number (N) but different atomic (Z) and mass number (A). they are called isotones
therefore
A) Option 3 and 4
B) Option 3 and 4
To learn more about Atomic Nucleus visit :
brainly.com/question/1268608
#SPJ4
Each contour line as you go inland
represents ground that is at a constant
elevation 5 meters higher than the
previous contour.
a) At what points on the map are there
steep cliffs? Show at least three
places.
b) There are two high areas, label the
How high are they?
Mark a straight-line path to climb
from sea level to the high point B
with the most gentle slope.
d) You are interested in how much work
it takes to lift your body mass from
sea level to the B peak. If you follow
the path you chose in part C will
you minimize the amount of work to
climb to the top, or will it make no
difference?
Each contour line as you go inland represents ground that is at a constant
elevation 5 meters higher than the previous contour are:
a) Steep cliffs can be found at points A, D, and F on the map.
b) High area A is 35 meters above sea level and high area B is 50 meters above sea level.
c) The path from sea level to high point B with the most gentle slope would be to follow the contour lines from sea level upwards in a spiral pattern, starting at point A and ending at point B.
d) Following the path in part C will minimize the amount of work to climb to the top, as it follows the contour lines which represent the most gentle slopes.
What is contour line?
A contour line is a line drawn on a map that connects points of equal elevation, such as the peaks and valleys of a landscape. Contour lines are used to show the shape of the land, which can help map-readers to understand the features of the terrain and the change in elevation of the landscape.
To learn more about contour line
https://brainly.com/question/6754543
#SPJ4
A ball is tossed off the edge of a cliff with the same speed but at different angles, as shown. From greatest to least, rank the (a) initial PEs of the balls relative to the ground below. (b) initial $\mathrm{KEs}$ of the balls when tossed. (c) $\mathrm{KEs}$ of the balls when they hit the ground below. (d) times of flight while airborne.
From greatest to least, rank is
a. A=B=C
b. A=B=C
c. A=B=C
d. B, A, C
How do you find initial potential energy?
The formula for potential energy depends on the force acting on the two objects. For the gravitational force, the formula is P.E. = mgh, where m is the mass in kilograms, g is the acceleration due to gravity (9.8 m / s2 at the surface of the earth) and h is the height in meters.
What is the formula for initial kinetic energy?
Kinetic energy is directly proportional to the mass of the object and to the square of its velocity: K.E. = 1/2 m v2. If the mass has units of kilograms and the velocity of meters per second, the kinetic energy has units of kilograms-meters squared per second squared.
What happens to kinetic energy when you throw a ball?
When a ball is thrown straight up into the air, all its initial kinetic energy is converted into gravitational potential energy when it reaches its maximum height.
To know more about potential and kinetic energy:
https://brainly.com/question/25959744
#SPJ4
1. A roller coaster cart of mass m = 341 kg starts
stationary at point A, where h1 = 23.3 m and
a while later is at B, where h2 = 9.3 m.
The acceleration of gravity is 9.8 m/s^2
2.What is the speed of the cart at B, ignoring
the effect of friction?
Answer in units of m/s. Answer in units of
m/s.
The speed of the cart at B is 16.56 m/s (ignoring the effect of friction).
What is law of conservation of energy?Energy cannot be created or destroyed, according to the law of conservation of energy. However, it is capable of change from one form to another. An isolated system's total energy is constant regardless of the types of energy present.
According to conservation of energy:
decrease in potential energy = increase in kinetic energy
341 × 9.8 × 23.3 - 341 × 9.8 × 9.3 = 1/2 × 341 ×v²
v² = 2 × 9.8 × (23.3 - 9.3)
v = 16.56 m/s.
Hence, the speed of the cart at B is 16.56 m/s.
Learn more about energy here:
https://brainly.com/question/1932868
#SPJ1
what is the effect on the color of a cloud when it contains an abundance of large droplets?
Large droplets in a cloud will scatter lower frequency light. The cloud will therefore seem reddish.
The term "hygroscopicity" refers to how much water an aerosol absorbs under a particular set of environmental conditions. Inorganic salts are the species that are most hygroscopic in the atmosphere. However, due to advantageous hydrogen-bonding interactions with water, oxygenated organic compounds can also be hygroscopic. Surface-active organic species further promote hygroscopicity by lowering surface tension. Not only can oxidation reactions in the atmosphere significantly contribute to increasing hygroscopicity by adding oxygen scattering, but they may also have an impact on how surface material is partitioned, which in turn affects cloud formation by causing changes in surface tension.
Learn more about scattering here-
https://brainly.com/question/9922540
#SPJ4
Chen displayed the results of her experiment in the graph that is show below.
What is the dependent variable in her experiment?
A. time (days)
B. duckweed genetics
C. amount of duckweed
D. different water pH levels
The correct answer is C. amount of duckweed.
What is independent variables?Independent variables are variables that can be manipulated or changed to observe their effects on a dependent variable. In other words, they are the input of a system. Examples of independent variables include temperature, time, and concentration. These variables are independent of each other and can be changed simultaneously or individually to observe their effects on the outcome.
The dependent variable in Chen's experiment is the amount of duckweed, which is represented on the y-axis of the graph. The independent variables in this experiment are the different water pH levels, which are represented on the x-axis. By plotting the amount of duckweed against the different water pH levels, Chen was able to analyze the effect of the different pH levels on the growth of duckweed.
To know more about independent variables click-
https://brainly.com/question/571013
#SPJ4
A uniformly charge d insulating rod of length 14.0cm is bent into the shape of a semicircle as shown in Figure. The rod has a total charge of −7.50μC. Find (a) the magnitude and (b) the direction of the electric field at O, the center of the semicircle.
The magnitude and (b) the direction of the electric field at O, the center of the semicircle is E = 2.16 × 10⁷ N/C and direction is Left.
Each location in space where a charge exists in any form can be considered to have an electric field attached to it. The electric force per unit charge is another name for an electric field. The electric field's equation is given as E = F / Q.
Due to symmetry,
Ey = ∫ dEy = 0,
and E¸ = − ∫ dE sin θ
= −ke∫ dq sinθ/ r2
where
dq=λds = λrdθ;
the component Ex is negative because charge q = -750µC,
causing the net electric field to be directed to the left.
Ex = Κeλ/r ∫ Sinθ
= - (Keλ) (- Cos θ) / r
= -2Keλ / r
where λ and r = L/ π.
Thus,
Ex = 2Ke |q|Π / L²
= [- 2(8.99 × 10⁹ N. m²/С²)(7.50 × 10 С)π] / (0.140 m)2
Ex = -2.16 × 10⁷ N/C
(a) magnitude E = 2.16 × 10⁷ N/C
(b) the direction of the electric field at O, the center of the semicircle is Left.
To learn more about Electric field from given link
https://brainly.com/question/14372859
#SPJ4
need help please answear with an easy and simple answer
The acceleration of the car is - 4.0m/s². Hence, option (B) is correct.
What is acceleration?Acceleration is rate of change of velocity with time. Due to having both direction and magnitude, it is a vector quantity. Si unit of acceleration is meter/second² (m/s²).
Initial velocity of the car: u = + 65 m/s.
Final velocity of the car: v = + 45 m/s.
Time interval: t = 5 seconds.
Hence, acceleration of the car = change in velocity/time interval
= (v - u)/t
= ( +45 - 65)/5 m/s²
= - 20/5 m/s²
= - .0m/s².
So, acceleration of the car is - 4.0m/s².
Learn more about acceleration here:
brainly.com/question/12550364
#SPJ1
Electrostatic precipitators use electric forces to remove pollutant particles from smoke, in particular in the smokestacks of coal-burning power plants. One form of precipitator consists of a vertical, hollow, metal cylinder with a thin wire, insulated from the cylinder, running along its axis (Figure 1). A large potential difference is established between the wire and the outer cylinder, with the wire at lower potential. This sets up a strong radial electric field directed inward. The field produces a region of ionized air near the wire. Smoke enters the precipitator at the bottom, ash and dust in it pick up electrons, and the charged pollutants are accelerated toward the outer cylinder wall by the electric field. Suppose the radius of the central wire is 80.0 um, the radius of the cylinder is 14.0 cm, and a potential difference of 50.0 kV is established between the wire and the cylinder. Also assume that the wire and cylinder are both very long in comparison to the cylinder radius.
What is the magnitude of the electric field midway between the wire and the cylinder wall?
The dielectric constant of water, also known as the relative permittivity of water, is approximately 80.
What is dielectric constant?The dielectric constant, also known as the relative permittivity, is a measure of a material’s ability to resist the flow of electric current when electric field is applied. It is a ratio of the amount of electric field needed to make a material conduct electric current compared to that of a vacuum. The higher the dielectric constant of a material, the more electric field is needed to make it conduct electric current. Common materials with high dielectric constants include glass, plastics, rubber, and water.
This is the ratio of the electric field of water to the electric field of a vacuum, which is calculated by dividing the speed of light in a vacuum (3.00 × 10^8 m/s) by the speed of light in water (2.26 × 10^8 m/s). This ratio indicates that the electric field of water is 80% of the electric field of a vacuum, meaning that the dielectric constant of water is 80.
To know more about dielectric constant click-
https://brainly.com/question/13873821
#SPJ4
A skier with a mass of 80.7 kg hits a ramp of snow at 16 m/s and becomes airborne. At the highest point of flight, the skier is 3.43 m above the ground. What is the skier’s gravitational potential energy at this point? Round your answer to the nearest ones place.
The gravitational potential energy of the skier is 2,712.65 J.
What is the skier’s gravitational potential energy?The skier’s gravitational potential energy at this point is calculated by applying the following formula.
P.E = mgh
where;
m is the mass of the skierg is acceleration due to gravityh is the height of the skierThe gravitational potential energy of the skier is calculated as follows;
P.E = ( 80.7 kg ) x ( 9.8 m/s² ) x ( 3.43 m )
P.E = 2,712.65 J
Thus, the gravitational potential energy of the skier is a function of the height and mass of the skier.
Learn more about gravitational potential energy here: https://brainly.com/question/15896499
#SPJ1
The centrifugal force exerted on rotating turbine blades varies directly as the square of velocity. If the centrifugal force of 1.21×106 N is acting on the blades that move at 550 m/sec, find the instantaneous rate of change of the centrifugal force as the velocity increases to 830 m/sec. Round the answer to the nearest whole number.
The instantaneous rate of change of the centrifugal force as the velocity increases to 830 m/sec is 4.14×106 N/sec.
What is velocity?
Velocity is a measure of the rate of change of the position of an object over time. It is a vector quantity, meaning it has both direction and magnitude. Velocity is determined by dividing the displacement of the object by the time it took to get there.
The centrifugal force exerted on rotating turbine blades is directly proportional to the square of velocity, such that F = kv2, where k is a constant. Therefore, the rate of change of the centrifugal force with respect to the velocity (dF/dv) can be expressed as:
dF/dv = 2kv
Substituting the values given, we have
dF/dv = 2(1.21×106 N/[550 m/sec]2) × 830 m/sec
dF/dv = 4.14×106 N/sec
Therefore, the instantaneous rate of change of the centrifugal force as the velocity increases to 830 m/sec is 4.14×106 N/sec.
To learn more about velocity
https://brainly.com/question/24445340
#SPJ4
1. Calculate the ratio of Jupiter's mass to the total mass of the Galilean moons.
Express your answer using two significant figures.
The jupiter's mass=1.898×10^27 kg , In 2 significant figures =1.9×10^27 kg The total mass of the Galilean moons =3.93×10^23 .
What does Total mass means?
Total mass is the sum of all the individual masses of the components within a system. It is a measure of the total amount of matter within the system, and is typically expressed in units such as kilograms, pounds, or grams. Total mass can be used to calculate the total amount of energy that is stored in a system, and is an important quantity in physics, chemistry, and materials science.
What does Material Science means?
Material Science is the study of the properties and characteristics of materials and their applications in engineering and technology. It is an interdisciplinary field that involves physics, chemistry, and engineering. It is also known as Materials Science and Engineering and encompasses the study of the structure and behavior of materials at various scales, from the atomic and molecular level to the macroscopic and microscopic scale.
To more about Total mass,
https://brainly.com/question/28021242
#SPJ4
Consider the first-order decomposition of A molecules (red spheres) in three vessels of equal volume.
A) What are the relative rates of decomposition in vessels (1)-(3)?
B) What are the relative half-lives of the reactions in vessels (1)-(3)?
C) How will the rates be affected if the volume of each vessel is decreased by a factor of 2?
D) How will the half-lives be affected if the volume of each vessel is decreased by a factor of 2?
Consider the first-order decomposition of A molecules (red spheres) in three vessels of equal volume - A) 2:4:3 , B) 1:1:1 , C) increase by a factor of 2, D) remain the same.
What is first-order decomposition ?
When the reaction's pace is proportional to the concentration of the reactant, it is referred to as a first-order reaction. On the other hand, as the concentration rises, the reaction rate doubles. One or two reactants are used in the decomposition process, an illustration of a first-order reaction.
What is molecules ?
A molecule is a collection of at least two chemically bound atoms from the same or distinct elements. One molecule of water, for instance, is created when two hydrogen atoms and one oxygen atom combine.
Therefore, the first-order decomposition of A molecules (red spheres) in three vessels of equal volume - A) 2:4:3 , B) 1:1:1 , C) increase by a factor of 2, D) remain the same.
Learn more about first-order decomposition from the given link.
https://brainly.com/question/13266271
#SPJ4
The magnetic force on a charged particle is in the direction of its velocity if a never
b. it is moving in the direction of the field c.it is moving perpendicular to the field d. it is moving in some other direction
b. it is moving in the direction of the field
When a charged particle is moving in a magnetic field, it experiences a force called the Lorentz force. The direction of this force is perpendicular to the both, the velocity of the particle and the magnetic field. If the velocity of the particle is in the same direction as that of the magnetic field, the Lorentz force is in the direction of the velocity of the particle. If the velocity of the particle is perpendicular to the magnetic field, the Lorentz force is also perpendicular to the velocity of the particle.
To know more about Lorentz force click below:
https://brainly.com/question/28211140#
#SPJ4
Because the t procedures are robust, the most important condition for their safe use is that
the population standard deviation σ is known.
the data can be regarded as an SRS from the population.
the population distribution is exactly Normal.
Because the t procedures are robust, the most important condition for their safe use is that the data can be regarded as an SRS from the population.
The fact that we have three possibilities is the most crucial requirement for their safe use. There are at least 15 samples. The distribution of the population is quite normal. The information can be viewed as a SRS from the well-known ship, thus we need to determine the best course of action. So, only small sample sizes are used when the t procedure is needed. In order to ensure that the best condition sample is chosen at random, these three The samples have a minimum of 15. Therefore, the data in this case can be viewed as a representative sample of the population. So here the answer will be the data can be regarded as an SRS from the population.
To know more about t procedures, click here:-
https://brainly.com/question/15833960
#SPJ4
Plane Mirror Question 2 (Grade 10 Science)
Answer:
Explanation:
The index of refraction (n) of a gem can be calculated using the formula:
n = c / v
where c is the speed of light in a vacuum (approximately 3 x 10^8 m/s) and v is the speed of light in the gem.
In this case, we know that the speed of light in the gem is l.q5 x 10^8 m/s. So, we can plug this value into the formula and calculate the index of refraction:
n = c / v = (3 x 10^8 m/s) / (l.q5 x 10^8 m/s) = 3 / l.q5
The value of n is a dimensionless number and it's usually between 1 and 2.
It's not possible to identify the gem using the index of refraction alone. There are many gems with similar indexes of refraction. Index of refraction alone is not enough to identify a gem. The gemstone's color, brilliance, and other physical and optical properties must be taken into account to identify it.
The index of refraction of the unknown gem is 1.54.
What is index of refraction?The index of refraction measures how a light beam bends when it travels through different media.
The refractive index is calculated by dividing the speed of light at a given wavelength in in vacuum space by its speed of light in that medium.
The speed of light in that gem = 1.95 × 10⁸ meter/second
The index of refraction of the unknown gem is = (speed of light in vacuum/speed of light in that gem)
= (3 × 10⁸ meter/second)/(1.95 × 10⁸ meter/second)
= 1.54.
Learn more about index of refraction here:
https://brainly.com/question/23750645
#SPJ1
Calculate the value of ψ2pz2 at r = a0 for θ = 0 (z axis) and for θ = 90° (xy plane)
0 is the correct answer .
What is angle ?
In Euclidean geometry, an angle is a figure formed by two rays, called the sides of the angle, that share a common endpoint called the vertex of the angle. The angle formed by two rays is in the plane containing the rays. These are called dihedral angles. Two intersecting curves can also define an angle. This is the angle of the ray tangent to each curve at the point of intersection.
Angle is also used to indicate a measure of angle or rotation. This measure is the ratio of the arc length to the radius of the circle. In geometric angles, arcs are centered at vertices and bounded by edges. For rotation, the arc is centered around the rotation and surrounded by all other points and its image by rotation.
To learn more about angle ,click the given link;
https://brainly.com/question/25716982
#SPJ4
What is the Big-Bang Theory?
The Big Bang theory is the prevailing cosmological model that explains the origins of the universe. According to the theory, the universe began as a singularity, a hot and infinitely dense point, approximately 13.8 billion years ago. From this singularity, the universe expanded and cooled, eventually leading to the formation of subatomic particles, atoms, stars, and galaxies. The theory also states that the universe is still expanding and it's getting cooler and larger.
The theory was first proposed by Belgian priest and physicist Georges Lemaître in 1927 and later developed by Edwin Hubble's observations of the redshifts of distant galaxies in the 1920s and 1930s. The theory has been extensively tested and supported by a wide range of observational evidence, including cosmic microwave background radiation and the large-scale structure of the universe.
To learn more about the big-bang theory:
brainly.com/question/15421576
Answer:
The Big-Bang Theory is the prevailing cosmological model for the universe from the earliest known periods through its subsequent large-scale evolution. The model describes how the universe expanded from an initial state of high density and high temperature, and offers a comprehensive explanation for a broad range of phenomena, including the abundance of light elements, the cosmic microwave background, large scale structure and Hubble's law. According to the Big-Bang Theory, the universe was once in an extremely hot and dense state which expanded rapidly. As it cooled, the first subatomic particles formed and then simple atoms, eventually leading to the formation of stars and galaxies. The Big-Bang Theory is supported by a wide range of scientific observations and provides a comprehensive explanation for the structure and evolution of the universe.
You examine the fine print in a legal contract with a magnifying glass of focal length 5.0 cm.
A.) How far from the lens should you hold the print to see a final virtual image 30 cm from the lens (at the eye's near point)?
*The answer is not 6 cm*
B.) Determine the angular magnification of the magnifying glass.
The focal length is 4.28cm and the magnification is 7.
What is focal length ?
A lens's focal length is established when it is focused at infinity. We can determine the magnification—how large individual elements will be—and the angle of view—how much of the picture will be captured—by knowing the focal length of the lens. The angle of view is smaller and the magnification is greater the longer the focal length.
What is angular magnification ?
The ratio between the angle that the image of an object at an unaided eye or without the apparatus subtends and the angle that the image subtends at the microscope is known as the angular magnification of the object.
We have the lens equation
1/ f = 1/ u = 1/ V
Here the image is virtual
so V = - 30
1/ f = 1/ u - 1/ v
1/ 5= 1/ u -1/ 30
1/5 + 1/ 30 = 1/ u
u = 4.28cm
magnification
m = -v/u
= - (-30)/ 4.28
= 7
Therefore, the focal length is 4.28cm and the magnification is 7.
Learn more about focal length from the given link.
https://brainly.com/question/1031772
#SPJ4