A golf ball is hit so that it leaves the club face at a velocity of 45m/s at an angle of 40° to the horizontal. by ignoring the effect of air resistance and spin on the ball, use the information to answer the question (a) to (d).
a) Calculate the horizontal component of the velocity
b) Determine the vertical component of the velocity.
c) Find the time taken for the ball to reach its maximum height.
d) Calculate the horizontal distance travelled when the ball is at its maximum height.​

Answers

Answer 1

Answer:a)45cos40 b)45sin40 c) 2.95 d)102

Explanation:

a) [tex]v_{x} = 45 cos40[/tex]

b) [tex]v_{y}=45sin40[/tex]

c) Since air resistance is negligible, the only force acting on the golf ball is gravity. Thus, its vertical acceleration is -g. We know the final velocity must be 0 m/s, because this will be when the golf ball reaches the maximum height and starts to change direction (it falls back to the ground). We also know initial velocity in the vertical direction (see part b). Thus, we can use this equation: [tex]v_{f} = v_{i} + at[/tex].

[tex]0 m/s = 45sin40 + (-9.8m/s^2)t\\t = 2.95s[/tex]

d) The horizontal distance traveled is dependent on (1) how long the ball is in the air and (2) what the horizontal velocity is. (1) was found in part c, and (2) was found in part a.

[tex]x=vt\\x=45cos40(2.95) =102m[/tex]


Related Questions

what happens when a wave passes through a medium ?

Answers

Answer:

When waves travel from one medium to another the frequency never changes. As waves travel into the denser medium, they slow down and wavelength decreases. Part of the wave travels faster for longer causing the wave to turn. The wave is slower but the wavelength is shorter meaning frequency remains the same.

Explanation:

Cole drives to school from home, starting from rest and accelerating for 10 minutes as he travels 6.0 km to school.
1) What is Cole's acceleration?
2) What is his velocity when he reaches school?

Answers

Explanation:

this is the answer for your question. if you have any doubt.

you can send your doubt to:6369514784(what's app)

Determine the voltage Vab for the first circuit and also determine the voltages Vab and Vcd for the second circuit

Answers

Vab= E = 20V

because I = 0 and the voltage drop across the resistances R1 and R2 is also 0.

Second circuit:

Vab = 10V (no voltage drop across R1)

Vcd= E2-E1 = 20V

Series connection of voltage sources. But the sources are connected to the contrary and voltage drop across R1 or R2 is 0 V.

Earth’s atmosphere traps energy from the sun. Which is a direct result of the trapping of energy by Earth’s atmosphere?

Answers

Answer:

Earth's atmosphere traps energy from the sun. Which is a direct result of the trapping of energy by earth's atmosphere? Earth has moderate temperatures.

Explanation:

What force causes a resistance in motion
when two surfaces are touching?

Answers

Answer:

FRICTION

Explanation:

Friction is a force, the resistance of motion when one object rubs against another.

Frictional force

Explanation:

Its the opposing force against horizontal motion

An astronaut named Sandra Bullock has drifted too far away from her spaceshuttle while attempting to repair the Hubble Space telescope. She realizes that theshuttle is moving away from her at 3 m/s. On her back is a 10 kg jetpack which consistsof an 8 kg holding tank filled with 2 kg of pressurized gas. Without the jetpack, sheand her space suit have a mass of 80 kg.

Required:
a. She is able to use the gas to propel herself in the same direction as the shuttle. The gas exits the tank at a uniform rate with a constant velocity of 100 m/s, relative to the tank (and her). After the gas in the tank has been released, what is her velocity?
b. After this, she throws her empty tank into space and relies on the conservation of momentum to increase her speed to match that of the shuttle. With what velocity (in her frame of reference!) will she have to throw the tank?

Answers

Answer:

a) v_f = 0.898 m / s, b)   v₂ = -6.286 m / s

Explanation:

a) For this exercise we use the conservation of momentum, we define a system formed by the astronaut, her equipment and the expelled gases. We must also define a stationary frame of reference, let's place the system on the platform, so the speed of the subject is v = -3 m / s

Initial instant. Before you start to pass gas

        p₀ = (M + Δm) v

M is the mass of the astronaut M  = 80Kg and Δm the masses of the gases

Final moment. When you expel the gases

        p_f = M (v + Δv) + Δm (v-v_e)

where v_e is the gas velocity v_e = 100 m / s

momentum is conserved

        p₀ = p_f

        M v + Δm v = Mv + M Δv + Δm v -Δm ve

          0 = M Δv - Δm v_e

         

if we make the very small quantities Δv → dv and Δm → dm, furthermore the quantity of output gas is equal to the decrease in the total mass dm = -dM

         M dv = -v_e dM

         ∫ dv = - v_e ∫ dM / M

We solve, between the lower limits v₀ = v with M = M₀   and the upper  limit v = v_f for M = M_f

 

         v_f - v₀ = - v_e (ln M_f - Ln M₀)

         v_f - v₀ = v_e ln ([tex]\frac{M_o}{M_f}[/tex])

         v_f = v₀ + v_e ln (\frac{M_o}{M_f})

let's calculate

         v_f = -1.3 + 100 ln (80 + 10 + 2/80 + 10)

          v_f = -1.3 +2.20

          v_f = 0.898 m / s

b) launch the jetpack to increase its speed up to the speed of the platform

  initial instant. Before launching the tanks

        p₀ = (M + m') v_f

final instnte. After launching the tanks

       p_f = M v₁ + m' v₂

indicate that the final velocity of the astronaut is the platform velocity v₁=0 m / s, since the reference system is fixed on it

       p₀ = p_f

       (M+ m) v_f = M v₁ + m v₂2

       v₂ = [tex]\frac{ M ( v_f - v_o) + m' v_f}{m'}[/tex]

        v₂ = [tex]\frac{M}{m}[/tex] (v_f -v₁) + v_f

let's calculate

        v₂ = 80/10 (0.898 - 0) + 0.898

        v₂ = -7.1874 + 0.898

        v₂ = -6.286 m / s

Galileo _____.

did not believe friction existed

believed that friction stopped objects in motion

believed that friction kept objects in motion

assumed that in a frictionless environment objects would never move

Answers

Answer:

friction help to slow motion in other word it oppose motion, but in a frictionless environment object would move with difficult stopping point.

Review Conceptual Example 8 before starting this problem. A block is attached to a horizontal spring and oscillates back and forth on a frictionless horizontal surface at a frequency of 3.96 Hz. The amplitude of the motion is 5.95 x 10-2 m. At the point where the block has its maximum speed, it suddenly splits into two identical parts, only one part remaining attached to the spring. (a) What is the amplitude and (b) the frequency of the simple harmonic motion that exists after the block splits

Answers

Answer:

a)  A' =  0.345  m,  b)  f = 2,800 Hz

Explanation:

b) The angular velocity of a simple harmonic motion is

        w =[tex]\sqrt{\frac{k}{m} }[/tex]

angular velocity and frequency are related

        w = 2π f

we substitute

        f = 1 /2π   √k/m

indicates that the initial frequency value f = 3.96 Hz

in this case the mass is reduced by half

       m ’= m / 2

we substitute

       f = 2π [tex]\sqrt{\frac{k}{m} }[/tex]

       f = √1/2    (2π √k/m)

       f = 1 /√2  3.96

       f = 2,800 Hz

a) The amplitude of the movement is defined by the value of the initial depalzamienot before an external force that initiates the movement.

When the block is divided into two parts of equal masses as if it were exploding, for which we can use the conservation of moment

initial instant. Right before the division

        p₀ = (m₁ + m₁) v

final instant. Right after the split

        p_f = m₁ v '

        p₀ = p_f

        (2 m₁) v = m₁ v ’

        v ’= 2v

At this point we can use conservation of energy for the system with only half the block.

Starting point. Where the block divides

         Em₀o = K = ½ m v'²

Final point. Point of maximum elongation

          Em_f = Ke = ½ k A²

how energy is conserved

         Em₀ = Em_f

         ½ m’ v’² = ½ k A’²

we substitute the previous expressions

         ½ m/2 (2v)² = ½ k A’²

         A’² = 2  m v² / k                       (1)

Let's use the conservation of energy with the initial conditions, before dividing the block

          ½ m v2 = ½ k A2

          A² = mv² / k = 5.95 10⁻² m²

we substitute in 1

         A'² = 2 A²

           

          A ’²=  2 5.95 10⁻²

          A ’²= 11.9 10⁻² m

          A' =  0.345  m

1. Three centimeters of water evaporated from a 200-hectare vertical walled reservoir during 24 hours. Storm water was added to the reservoir at a constant rate of 3 m3/s during this period. Determine the volume in ha-cm of water released during the period (through the bottom of the reservoir) if the water level was the same at the beginning and the end of the day.

Answers

Answer:

25920 ha-cm

Explanation:

Since water evaporates from the reservoir at a rate of 3 cm in 24 hours, its height changes at a rate of 3 cm/24 × 3600 s = 3 cm/86400s = 3.472 10⁻⁵ cm/s.

Now, the volume loss is dV/dt = dV/dh × -dh/dt

= dV/dt × -3.472 × 10⁻⁵ cm/s

= -3.472 × 10⁻⁵ cm/sdV/dh

The reservoir increases in volume at a rate of 3 m³/s = 3 × 10⁶ cm³/s in 24 hours.

So, the net rate of volume change per unit time of the reservoir is

3 × 10⁶ cm³/s  - 3.472 × 10⁻⁵ cm/sdV/dh = Adh/dt where A = area of vertical walled reservoir and dh/dt = change in height of the reservoir with respect to time

So, 3 × 10⁶ cm³/s  - 3.472 × 10⁻⁵ cm/sdV/dh = Adh/dt

Since dh/dt = 0 in 24 hours(since the water level remains the same after 24 hours, that is dh = 0)

3 × 10⁶ cm³/s  - 3.472 × 10⁻⁵ cm/sdV/dh = Adh/dt

3 × 10⁶ cm³/s  - 3.472 × 10⁻⁵ cm/sdV/dh = A × 0

3 × 10⁶ cm³/s  - 3.472 × 10⁻⁵ cm/sdV/dh = 0

3.472 × 10⁻⁵ cm/sdV/dh = 3 × 10⁶ cm³/s

dV/dh = 3 × 10⁶ cm³/s ÷ 3.472 × 10⁻⁵ cm/s

dV/dh = 8.64 × 10¹¹ cm²

dV = (8.64 × 10¹¹ cm²)dh

Integrating both sides with V from 0 to V and h from h = 0 to h = 3 cm, we have

∫dV = ∫(8.64 × 10¹¹ cm²)dh

∫dV = (8.64 × 10¹¹ cm²)∫dh

V = (8.64 × 10¹¹ cm²)[h]₀³

V = (8.64 × 10¹¹ cm²)[3 cm - 0 cm]

V = (8.64 × 10¹¹ cm²)(3 cm)

V = 25.92 × 10¹¹ cm³

V = 2.592 × 10¹² cm³

V = 2.592 × 10¹² cm² × 1 cm

Since 1 ha = 10⁸ cm²,

V = 2.592 × 10¹² cm² × 1 ha/10⁸ cm² × 1 cm

V = 2.592 × 10⁴ ha-cm

V = 25920 ha-cm

Tell types of mirros and
each
one​

Answers

Answer: We can identify the different types of mirrors without touching them by looking at the image it produces. Look into each mirror, the nature of the image produced will tell you the type of mirror it is.

- A plane mirror will produce an image of the same size as your face.

- A concave mirror will produce a magnified image of your face.

- A convex mirror will produce a diminished image of your face.

MARK ME BRAINLIST

Two train whistles have identical frequencies of 180 Hz. When one train is at rest in the station and the other is moving nearby, a commuter standing on the train platform hears beats with a frequency of 2.00 beats/s when the whistles sound at the same time. What are the two possible speeds and directions that the moving train can have?

Actual answers :3.85 m/s away from the station and 3.77 m/s towards the station from the book. I just need to know how to get to the answers.

Answers

Answer:

-3.77 m/s

3.85 m/s

Explanation:

given that

Frequency at stationary = 180 Hz

Beat frequency = 2 Hz

Using Doppler effect, we know that

f' = f[(v ± v0) / (v ± vs)], where

v = speed of sound, 343 m/s

v0 = speed of the observer, 0

vs = speed of light, ?

f = stationary frequency, 180 Hz

f' = stationary ± beat frequency, 180 ± 2

Applying the formula, we have

f' = f[(v ± v0) / (v ± vs)]

182 = 180 [(343 + 0) / (343 + vs)]

182/180 = 343 / 343 + vs

343 + vs = 343 * 180/182

343 + vs = 339.23

vs = 339.23 - 343

vs = -3.77 m/s

Again, using

f' = f[(v ± v0) / (v ± vs)]

178 = 180 [(343 + 0) / (343 + vs)]

178/180 = 343 / 343 + vs

343 + vs = 343 * 180/178

343+ vs = 346.85

vs = 346.85 - 343

vs = 3.85 m/s

Plzzz answer this question correctly

Answers

Answer:

changing the direction in which a force is exerted

What current is needed in the solenoid's wires?

A researcher would like to perform an experiment in a zero magnetic field, which means that the field of the earth must be canceled. Suppose the experiment is done inside a solenoid of diameter 1.0 m, length 3.8 m , with a total of 5000 turns of wire. The solenoid is oriented to produce a field that opposes and exactly cancels the 52 μT local value of the earth's field.

What current is needed in the solenoid's wires? Express your answer with the appropriate units.

Answers

Using Ampere's Law, the magnetic field produced inside this solenoid is given by
B = uo N I / h
where uo is the vacuum permeability, N is the number of turns in the solenoid and h is the length of the solenoid. Earth's magnetic field is around 50 microteslas in North America thus the current needed in the solenoid is
I = B h / (uo N) = (50 E-6 ) (4) / ((4 pi E-7)(6000) ) = 0.026 A
I = 26 mA
So you need a current of around 26 mA.

The solar wind consists of protons from the Sun moving toward Earth (the wind actually consists of about 95% protons). The number density of protons at a distance from the Sun equal to the orbital radius of Earth is about 7.0 protons per cubic centimeter. Your research team monitors a satellite that is in orbit around the Sun at a distance from the Sun equal to Earth's orbital radius. You are in charge of the satellite's mass spectrometer, an instrument used to measure the composition and intensity of the solar wind. The aperture of your spectrometer is a circle of radius 28.4 cm. The rate of collection of protons by the spectrometer is such that they constitute a measured current of 91.0 nA. What is the speed of the protons in the solar wind

Answers

Answer:

[tex]\mathbf{V_d = 3.2 \times 10^5 \ m/s}[/tex]

Explanation:

[tex]\text{The speed of the protons can be estimated by using the formula:}[/tex]

[tex]V_d = \dfrac{I}{enA}[/tex]

[tex]where;[/tex]

[tex]\text{e = proton charge}[/tex]

[tex]\text{n = No. of protons per unit volume}[/tex]

[tex]\text{A = area of aperture}[/tex]

[tex]V_d = \dfrac{91 \times 10^{-9} \ A}{(1.602 \times 10^{-19} \ C (7.0 \times 10^6 \ m^{-3} ) (\pi) (0.284 \ m)^2}[/tex]

[tex]\mathbf{V_d = 3.2 \times 10^5 \ m/s}[/tex]

What is the weight of a 44.5 kg object?

Answers

Answer:

98.11 I think

Explanation:

I really hope this helps have a wonderful day

3. Consider a large windmill 30m in diameter. On a windy day, suppose that the windmill entrains a stream of air at a speed of 40 mph. Downstream of the windmill, the entrained stream exits over a large diameter at a speed of 20 mph. The pressure is 2atm at the inlet and equals atmospheric pressure at the outlet. Find the power (in megawatts) generated by the windmill. Density of air is 1.2 kg/m3

Answers

Answer:

The power generated by the windmill is approximately 1.364 MW

Explanation:

The diameter of the windmill, d = 30 m

The inlet speed of the wind, [tex]V_e[/tex] = 40 mph = 17.88 m/s

The exit stream velocity, [tex]V_i[/tex] = 20 mph = 8.94 m/s

The pressure at the inlet, P₁ = 2 atm

The pressure at the outlet, P₂ = 1 atm

The density of air, ρ = 1.2 kg/m³

The power obtained from the windmill, 'P', is given as follows;

[tex]P =\dfrac{1}{4 \cdot g_c} \cdot \rho \cdot A \cdot (V_i + V_e)\cdot (V_i^2 - V_e^2)[/tex]

Where;

[tex]g_c[/tex] = 1.0 kg/(N·s²)

A = Cross-sectional rea of the the windmill =  π·D²/4 = π×(30 m)²/4 = 706.858347 m²

Plugging in the values, we get;

[tex]P =\dfrac{1}{4 \times 1.0} \times1.2 \times 706.858347 \times (17.88 + 8.94)\cdot (17.88^2 - 8.94^2) = 1363668.19438[/tex]

The power generated by the windmill, P ≈ 1363668.19438 W ≈ 1.364 MW.

Which of the following would have the least amount of inertia? Assume all the bags are the same size.

bag of rocks

bag of feathers

bag of bricks

bag of sand

Answers

Bag of feathers because it weighs the least

An electron, tial well may be anywhere within the interval 2a. So the uncertainty in its position is Δx= 2a. There must be a corresponding uncertainty in the momentum of the electron and hence it must have a certain kinetic energy. Calculate this energy from the uncertainty relationship and compare it.

Answers

Answer:

      [tex]K = \frac{h'}{8 m \ \Delta x^2}[/tex]K

Explanation:

The Heisenberg uncertainty principle is

          Δx Δp ≥ h' / 2

          h’ =[tex]\frac{h}{2\pi }[/tex]

The kinetic energy of a particle is

          K = ½ m v²

           p = mv

           v = [tex]\frac{p}{m}[/tex]

substitute

           K = [tex]\frac{1}{2} \frac{p^2}{m}[/tex]

from the uncertainty principle,

           Δp = [tex]\frac{h'}{2 \ \Delta x}[/tex]

we substitute

          K = [tex]\frac{1}{2m} ( \frac{h'}{2 \ \Delta x})^2[/tex]

          [tex]K = \frac{h'}{8 m \ \Delta x^2}[/tex]

A 0.15 kg baseball collides with a 1.0 kg bat. The ball has a velocity of 40 m/s immediately before the collision. The center of mass of the bat also has a velocity of 40 m/s, but in the opposite direction, just before the collision. The coefficient of restitution between the bat and the ball is 0.50. Estimate how fast the baseball is moving as it leaves the bat following the collision.

Answers

Answer:

The final velocity of the baseball as it leaves the bat is 40 m/s

Explanation:

The given parameters of the baseball and bat are;

The mass of the baseball = 0.15 kg

The mass of the bat = 1.0 kg

The velocity of the ball before collision, v₁ = 40 m/s

The velocity of the bat before collision, v₂ = -40 m/s

The coefficient of restitution, e = 0.50

Let, 'v₃', and 'v₄' represent the final velocity of the ball and the bat respectively after collision, we have;

Taking the final velocity of the bat, v₄ = 0 m/s

According to Newton's Law of restitution

e = (v₃ - v₄)/(v₁ - v₂)

∴ 0.5 = (v₃ - v₄)/(40 - (-40))

80 × 0.5 = 40 = (v₃ - v₄)

v₃ - v₄ = 40

v₃ =  40 + v₄ = 40 + 0 = 40

The final velocity of the baseball as it leaves the bat, v₃ = 40 m/s.

Which instrument would make rice vibrate easier, a tuba or a flute? Explain why. Hint: think about the difference between high and low notes in terms of vibrating atoms.

Answers

Answer:

I assume the higher notes would make the rice vibrate more easily, so a flute.

6th grade science I mark as brainliest

Answers

Answer:

8. organelle

Explanation:

9. Epithelial tissue

am i correct?


To fully describe velocity you must have a _____
A. Magnitude and unit
B. Speed and unit
C. Average speed and position
D. Magnitude and direction

Answers

I’m pretty sure the answer is C.

Valence electron of the first 20 elements​

Answers

Answer:

Hydrogen

1 valence electron

Helium

2 valence electrons

lithium

1 valence electrons

beryllium

2 valence electrons

boron

3 valence electrons

carbon

4 valence electrons

nitrogen

5 valence electrons

oxygen

6 valence electrons

flourine

7 valence electrons

neon

8 valence electrons

sodium

1 valence electron

magnesium

2 valence electrons

aluminum

3 valence electrons

silicon

4 valence electrons

phosphorus

5 valence electrons

Answer:  17 Chlorine -1, +1, (+2), +3, (+4), +5, +7

18 Argon 0

19 Potassium +1

20 Calcium +2

Explanation:

What is the mass of 9.11 moles of
ozone, 03?

Answers

O3 has molar mass of 48 g/mol

Therfore I mole weighs 48 grams

9.11 moles of ozone has a mass of 9.11 x 48grams = 437grams = 0.437kg

The molecular mass of [tex]$O_{3}[/tex] is 0.43728kg

What is molecular mass?

Molecular mass exists as a number equivalent to the totality of the atomic masses of the atoms in a molecule.  The totality of the atomic masses of all atoms in a molecule is established on a scale in which the atomic masses of hydrogen, carbon, nitrogen, and oxygen exist 1, 12, 14, and 16, respectively.

To compute the Molecular Mass of [tex]$O_{3}[/tex]

Atomic mass of oxygen(O) = 16

As [tex]$O_{3}[/tex] contains 3 atoms,

The molecular mass of [tex]$O_{3}[/tex]

= (16 x 3) = 48g/mol

Hence the mass of 9.11 moles O3

= 9.11 mol x 48g/mol

= 437.28g

= 0.43728kg

Therefore, the molecular mass of [tex]$O_{3}[/tex] is 0.43728kg

To learn more about Molecular mass refer to:

https://brainly.com/question/24727597

#SPJ2

Light of wavelength 425.0 nm in air falls at normal incidence on an oil film that is 850.0 nm thick. The oil is floating on a water layer 1500 nm thick. The refractive index of water is 1.33, and that of the oil is 1.40. The number of wavelengths of light that fit in the oil film is closest to:

Answers

Answer:

in oil film        λ = 303.57 10⁻⁹ m

in the water film    λ = 319.55 10⁻⁹ m

Explanation:

When electromagnetic radiation reaches a material, its propagation is by a process that we call absorption and reflection,

when light reaches a surface it has a mass much greater than the mass of the photons (m = 0), therefore there is an elastic collision where the frequency does not change, due to the speed of light in the material medium changes, therefore the only possibility is that the wavelength in the material changes, to maintain the relationship

             v = λ f

in the void we have

             c = λ₀ f

we divide the two expression

            c / v = λ₀ / λ

the refractive index is

             

              n = c / v

              n = λ₀ /λ

              λ = λ₀ / n

let's calculate

in oil film

            λ = 425 10⁻⁹ / 1.40

            λ = 303.57 10⁻⁹ m

in the water film

            λ = 425 10⁻⁹ / 1.33

            λ = 319.55 10⁻⁹

those wavelengths are in the ultraviolet

Dogs can inherit four features: fur pattern, fur
length, ear length, and tail length. The alleles are expressed as shown:
Dominant alleles
Recessive alleles
F: spotted fur
f: solid-colored fur
L: long fur
1: short fur
E: long ears
e: short ears
T: long tail
t: short tail
Two dogs mate and have puppies. Both parent dogs are heterozygous for spotted fur. Fill in the Punnett square to show the po
dropping the letters)

Answers

Answer:

This is something for biology, it shouldnt be in the physics subject

Explanation:

Friction is necessary when you are on a bike to stay

Answers

Answer:

yes friction is needed hope this helps might of been to long tho

QUESTION 9 / 10
What is the first step you should take when you want to open a savings account?
A. Present your photo ID to the bank representative,
B. Make your initial deposit.
C. Review the different savings account options that your
bank offers.
D. Go to the bank and fill out an application.

Answers

Answer:

A

Explanation:

AWNSER:

awnser:

C

explanation:

Which part of the water cycle is where vapor from plants leaves the plants as they breath?
condensation
Transpiration
evaporation

Answers

Answer:

I think it is transpiration

Answer:

transpiration is the right answer

Help plz I’ll mark brainliest

Answers

Answer:

The second option- a substance that a wave can travel through.

Explanation:

Hope This Helps!!

(brainliest please)

I believe that a medium is a substance that a wave can travel through
Other Questions
Which one of the following should earn the lowest risk premium based on CAPM?U.S. Treasury Billportfolio with a beta of .75stock with a beta of 1.35diversified portfolio with returns similar to the overall market Consider an economy where demand for real money balances is (M / P)^D = eY fi + . The variable represents the effect of any special factors, other than real income or the nominal interest rate, that might affect money demand. The real interest rate is r=iE. The money supply M^S is determined by the central bank. a) Derive an equation that gives (M / P)D as a function of Y, E , r and . In this equation, (M / P)^D should be alone on the left-hand side. b) Starting from your answer to a), do some algebra and derive an equation that gives r as a function of (M / P)^D, Y, E and .This is the "equation of the money demand curve." in ________ a neutral person investigates a complaint and develops findings that may be the basis for resolving an employee complaint.a. fact findingb. arbitrationc. poor employee performance What is the statute titled "harassment by persons in certain correctional facilities" also known as? how do you find the area of a surface prism Which of the following statement is NOT correct? (a) Scientific applications is one of the major programming domains, which involves in large numbers of floating point computations. (b) Artificial intelligence needs efficiency because of continuous use in programs like LISP. The significance of Programming language for business applications includes production of reports, use of decimal numbers and characters. (d) All of the above are correct. when dual or variable rate commission arrangements are made, the listing broker is obligated to do all the following except reliving some of our childhood experiences of loneliness can someone help me with this assignment pls ill give 50p and brainliest its due in 1 hour(javascript) in a(n) ______________________________ billing system, invoices are prepared after the goods have been shipped and the sales order notification has been matched to the shipping billing notification. All of the following were effects of the Vietnam War EXCEPT (1 pt. )South Vietnam kept its independenceLBJ's Great Society was defundedCommunism did not spread as was previously fearedCongress regained some war powersIsolationist foreign policy why is the molten metallic outer core and the magnetic field important to life on earth?if we did not have the molten core and the magnetic field, the earth would not have plate tectonics and would be covered entirely by water.if we did not have the molten core and the magnetic field, the atmosphere would be very different with either too much ammonia and methane or too little oxygen and water. Identify the body's fuel source as its metabolic pathways shift from feasting to fasting. Glycogen stores Body fat stores Body protein Fuel for the body 2 to 3 hours after eating Fuel for the body after 24 hours of starvation Fuel for the brain 2 to 3 hours after eating Fuel for the brain after 24 hours of starvation O select the best answer that is true about this reaction. hcl(aq) ca(oh)2(aq) 2 h2o(l) 2 cacl2(aq) How many grams of potassium iodide, , are present in 275 mL of a 0. 23 M solution? Blossom Company, a machinery dealer, leased a machine to Dexter Corporation on January 1, 2020. The lease is for an 8-year period and requires equal annual payments of $28,865 at the beginning of each year. The first payment is received on January 1, 2020. Blossom had purchased the machine during 2016 for $100,000. Collectibility of lease payments by Blossom is probable. Blossom set the annual rental to ensure a 6% rate of return. The machine has an economic life of 10 years with no residual value and reverts to Blossom at the termination of the lease. Click here to view factor tables. Your answer is correct. Compute the amount of the lease receivable. (For calculation purposes, use 5 decimal places as displayed in the factor table provided and round final answer to 0 decimal places e. G. 5,275. ) Amount of the lease receivable $ 190000 Prepare all necessary journal entries for Blossom for 2020. (Credit account titles are automatically indented when amount is entered. Do not indent manually. Round answers to 0 decimal places e. G. 5,275. ) Date Account Titles and Explanation Debit Credit 1/1/20 Right-of-Use Asset Lease Receivable Cash (To record the lease) Lease Liability Cash (To record the first lease payment) 12/31/20 Suppose the collectibility of the lease payments was not probable for Blossom. Prepare the necessary journal entry for the company in 2020. (Credit account titles are automatically indented when amount is entered. Do not indent manually. ) Date Account Titles and Explanation Debit Credit 1/1/ 200 C e Textbook and Media List of Accounts X Your answer is incorrect. Suppose at the end of the lease term, Blossom receives the asset and determines that it actually has a fair value of $900 instead of the anticipated residual value of $0. Record the entry to recognize the receipt of the asset for Blossom at the end of the lease term. (Credit account titles are automatically indented when amount is entered. Do not indent manually. Round answers to 0 decimal places e. G. 5,275. ) Date Account Titles and Explanation Debit Credit 1/1/20 a problem with live systems forensics in which data is not acquired at a unified moment is: the american bar association recommends that all felony cases reach disposition within: a study which observes whether a particular occurrence influences some outcome is referred to as a(n): a. event study. b. comparative study. c. exponential study. d. laboratory study The teacher thought the narrator was a troublemaker? Was he really or was there another reason for drawing attention to himself?