From the given empirical formula and molar mass, find the molecular formula of each compound.Part A:C6H7N , 372.54 g/molExpress your answer as a chemical formulaPart B:C2HCl , 181.42 g/molExpress your answer as a chemical formula.Part C:C5H10NS2 , 593.13 g/molExpress your answer as a chemical formula

To determine the amount of maleic anhydride in moles saved, we need to know the amount of anthracene used in moles first. The molar mass of anthracene is 178.24 g/mol, so the amount of anthracene used in moles is:
0.108 g / 178.24 g/mol = 0.000607 mol

Next, we need to determine the limiting reagent. We can do this by comparing the amount of anthracene used to the stoichiometric ratio between anthracene and maleic anhydride. The balanced equation for the reaction between anthracene and maleic anhydride is:
C14H10 + 3C4H2O3 -> 3CO2 + 2H2O + C18H8O4
The stoichiometric ratio between anthracene and maleic anhydride is 1:3. Therefore, the maximum amount of maleic anhydride that can be produced from the amount of anthracene used is:
0.000607 mol * 3 = 0.001821 mol
Since the amount of maleic anhydride saved is not given, we cannot determine if it is the limiting reagent or not.

To know more about anthracene visit:

https://brainly.com/question/26301677

#SPJ11

The balanced chemical equations for each reaction are:

Note: NR was not written as none of the reactions mentioned did not occur.

In chemistry, a chemical equation or chemical equation is the symbolic writing of a chemical reaction. The chemical formulas of the reactants are written to the left of the equation and the chemical formulas of the products are written to the right.

#SPJ11

The value of Ka for HA is 3.0 × [tex]10^{-5}[/tex]

The pH of a weak acid solution is related to the dissociation constant Ka and the concentration of the acid. We can use the Henderson-Hasselbalch equation to relate pH and Ka:

pH = pKa + log([A-]/[HA])

Where pH is the measured pH of the solution, pKa is the negative logarithm of Ka, and [A-] and [HA] are the concentrations of the conjugate base and weak acid, respectively. In this case, we know that the pH of the solution is 5.35 and the concentration of the weak acid is 0.15 M. We can use the Henderson-Hasselbalch equation to solve for pKa:

5.35 = pKa + log([A-]/[HA])

log([A-]/[HA]) = 5.35 - pKa

Taking antilog of both sides, we get:

[A-]/[HA] = [tex]10^{(5.35 - pKa)}[/tex]

We also know that Ka for HA is given as 3.0 × [tex]10^{-5.3}[/tex].

pKa = -log(Ka) = -log(3.0 × [tex]10^{-5.3}[/tex]) = 5.3

Substituting this value in the previous equation, we get:

[A-]/[HA] = [tex]10^{(5.35 - 5.3)}[/tex] = 1.78

We know that [HA] + [A-] = 0.15 M, so we can write:

[HA] = [HA] + 1.78[HA]

[HA] = 0.064 M

The concentration of the conjugate base [A-] is then:

[A-] = 0.15 M - 0.064 M = 0.086 M

Finally, we can use the equilibrium expression for Ka to calculate the concentration of H+ and the pH of the solution:

Ka = [H+][A-]/[HA]

[H+] = [tex]\sqrt{(Ka[HA]/[A-])}[/tex] = 1.7 × [tex]10^{-6}[/tex] M

pH = -log[H+] = 5.77

Therefore, the correct answer is 3.0 × [tex]10^{5.3}[/tex], and the pH of the solution is 5.77.

Know more about Henderson-Hasselbalch equation here:

https://brainly.com/question/13423434

#SPJ11

The correct answer is: less, more.When illustrating bond dipoles, vectors point from the less electronegative atom to the more electronegative atom.

This is because the more electronegative atom pulls the shared electrons closer to itself, resulting in a partial negative charge on that atom and a partial positive charge on the less electronegative atom. The bond dipole represents the separation of charges in a polar covalent bond. Therefore, the correct answer is "O less, more."When illustrating bond dipoles, vectors point from the less electronegative atom to the more electronegative atom. This is because bond dipoles represent the direction of electron density within a polar covalent bond. The more electronegative atom attracts electrons more strongly, causing a partial negative charge (δ-) to develop on that atom. Conversely, the less electronegative atom experiences a partial positive charge (δ+). The vector points towards the more electronegative atom to show the direction of electron density shift in the bond.

learn more about atom

https://brainly.com/question/1566330

#SPJ11

If 12.0 mL of OH⁻ were added, the quantity in moles of OH⁻ present would be 0.00289 mol, which is the same as the number of moles of CSOH added.

The given balanced chemical equation for the reaction of C₅H₅NHCl with CSOH is:

C₅H₅NHCl + CSOH → C₅H₅NH₂ + H₂O + CsCl

We can see that one molecule of CSOH reacts with one molecule of C₅H₅NHCl to form one molecule of C₅H₅NH₂. Therefore, we need to determine which of the reactants, C₅H₅NHCl or CSOH, is the limiting reactant.

The number of moles of C₅H₅NHCl in the 20.0 mL of 0.220 M solution is:

moles of C₅H₅NHCl = Molarity x Volume (in liters)

moles of C₅H₅NHCl = 0.220 mol/L x 0.0200 L

moles of C₅H₅NHCl = 0.0044 mol

The number of moles of CSOH in the 12.0 mL of 0.241 M solution is:

moles of CSOH = Molarity x Volume (in liters)

moles of CSOH = 0.241 mol/L x 0.0120 L

moles of CSOH = 0.00289 mol

Since C₅H₅NHCl and CSOH react in a 1:1 stoichiometric ratio, we can see that CSOH is the limiting reactant, and the amount of OH⁻ ions produced will depend on the amount of CSOH added.

The balanced equation shows that for every molecule of CSOH that reacts, one molecule of OH⁻ is produced. Therefore, the number of moles of OH⁻ produced by the reaction is equal to the number of moles of CSOH added:

moles of OH⁻ = 0.00289 mol

For more question on moles click on

https://brainly.com/question/29367909

#SPJ11

Answer: A Crane is not an example of rigging equipment.

Explanation: A Crane is not an example of rigging equipment.

The wire is not an example of rigging equipment. So option D is correct.

Hoisting means all equipment and materials used to lift and carry heavy objects. Cranes, plastic straps, and alloy steel chains are examples of rigging equipment. Wire, on the other hand, is not generally considered a rigging material.

To learn more about rigging:

https://brainly.com/question/30224374

https://brainly.com/question/31785488

The limiting reactant in the first trial is S, and the heat released is -77.8 kJ. The limiting reactant in the second trial is Na2O2, and the heat released is also -77.8 kJ. Therefore, option D, Na2S2 and 61 kJ, is not correct.

We must first identify the limiting reactant in each attempt. The reaction's chemically balanced equation is as follows:

Na2O2(s), S(s), and H2O(l) produce NaHSO4(aq).

We can compute the number of moles of each reactant in each trials using the molar masses of Na2O2 and S.

The moles of Na2O2 and S in the first experiment are 7.8 g/78 g/mol and 3.2 g/32 g/mol, respectively. S is the limiting reactant as a result.

The moles of S are 6.4 g/32 g/mol and the moles of Na2O2 are 7.8 g/78 g/mol in the second trial, respectively. Na2O2 is the limiting reactant as a result.

learn more about  limiting reactant here:

https://brainly.com/question/14225536

#SPJ11

The explanation for this is that oxygen has a higher electronegativity and a greater attraction for its valence electrons compared to boron, carbon, and sodium. This means that it requires more energy to remove an electron from oxygen, resulting in the formation of a cation.

To determine which element requires the most energy to remove a valence electron, we need to consider ionization energy. Ionization energy is the energy required to remove an electron from an atom or ion. In general, ionization energy increases from left to right across a period and decreases from top to bottom within a group on the periodic table.

Locate the elements on the periodic table. Boron, Carbon, Oxygen, and Sodium are in groups 13, 14, 16, and 1, respectively. Observe the ionization energy trends. Since ionization energy increases from left to right across a period, Oxygen in group 16 will have a higher ionization energy than Boron, Carbon, and Sodium. Consider the vertical trend. Ionization energy decreases from top to bottom within a group, but since all these elements are in the same period, this trend is not relevant for this comparison.
To know more about sodium visit :

https://brainly.com/question/29327783

#SPJ11

If a pH meter is not able to give an accurate measurement, it may need to be calibrated. This process requires a buffer solution of known pH values.

Calibration of a pH meter is essential to ensure that the device is providing accurate and reliable measurements. The process involves using buffer solutions with known pH values to adjust the pH meter to the correct readings. Typically, at least two buffer solutions with different pH values are used to provide a range of calibration points. These buffer solutions are commercially available and are specifically designed for the purpose of calibrating pH meters.

To perform the calibration, the pH meter's electrode is first rinsed with distilled water and then placed into the first buffer solution. The meter is then adjusted to match the known pH value of the buffer. The electrode is rinsed again and placed into the second buffer solution, and the meter is adjusted once more to match the pH value of this solution. This process helps to establish a more accurate and precise pH reading for the samples being tested.

In addition to calibration, it is important to maintain and clean the pH meter's electrode regularly to ensure its proper functioning. Proper storage of the electrode and prompt replacement of any worn or damaged parts will also contribute to the reliability and accuracy of the pH meter's readings. By following these steps, users can have confidence in the accuracy of their pH measurements.

Know more about pH meter here:

https://brainly.com/question/28206707

#SPJ11

Doubling the stoichiometric coefficients does not change the standard cell potential (Eºcell) for the reaction.

To determine how the standard cell potential (Eºcell) for a reaction changes when all stoichiometric coefficients are doubled, we need to understand the relationship between the standard cell potential and the stoichiometric coefficients.

In a balanced redox reaction, the stoichiometric coefficients represent the molar ratios of the reactants and products.

The standard cell potential, Eºcell, is related to the difference in standard reduction potentials (Eºred) between the oxidizing and reducing species involved in the reaction.

When all stoichiometric coefficients are doubled, the overall reaction equation and the half-cell reactions remain balanced.

Doubling the stoichiometric coefficients does not alter the ratio of the standard reduction potentials or the net change in potential for each half-cell reaction.

Therefore, the standard cell potential, Eºcell, does not change when all stoichiometric coefficients are doubled.

In summary, doubling the stoichiometric coefficients in a balanced redox reaction does not affect the standard cell potential, Eºcell, for the reaction.

Learn more about stoichiometric

brainly.com/question/6907332

#SPJ11

The weakest acid is HClO. Its conjugate base, ClO-, is the most stable due to its larger size and ability to disperse charge.

In more detail, the strength of an acid is determined by its ability to donate a proton (H+) to a base. The conjugate base of the acid is formed when the proton is lost. The stability of the conjugate base is inversely related to the strength of the acid; a weaker acid has a more stable conjugate base. In the case of HClO, the ClO- conjugate base is stabilized by its larger size and ability to disperse charge over a larger area, making it the most stable of the conjugate bases listed. Therefore, HClO is the weakest acid.

Learn more about weakest acid here;

https://brainly.com/question/17028693

#SPJ11

Therefore, the time required for a current of 0.60 A to pass through the solution and liberate 0.240 L volume of gas at STP is 1631 seconds (or approximately 27 minutes and 11 seconds).

The volume of gas liberated at STP (Standard Temperature and Pressure) is directly proportional to the quantity of charge passed through the solution. The quantity of charge passed through the solution is given by:

Q = It

where Q is the quantity of charge, I is the current and t is the time.

From the ideal gas law, the volume of gas at STP can be calculated as:

V = nRT/P

where n is the number of moles of gas, R is the universal gas constant, T is the temperature and P is the pressure.

At STP, the temperature T = 273 K and the pressure P = 1 atm. The number of moles of gas can be calculated using the equation:

n = PV/RT

where V is the volume of gas liberated.

Substituting the values given in the problem statement, we have:

n = (1 atm)(0.240 L)/(0.0821 L·atm/K·mol)(273 K) = 0.0101 mol

The charge required to liberate 0.0101 mol of hydrogen gas is:

Q = nF

where F is the Faraday constant, which is 96,485 C/mol.

Q = (0.0101 mol)(96,485 C/mol) = 978.6 C

Finally, the time required for a current of 0.60 A to pass through the solution and liberate the required amount of gas is:

t = Q/I = 978.6 C/0.60 A = 1631 s

To know more about volume,

https://brainly.com/question/25252629

#SPJ11

To calculate the emf (electromotive force) of the given concentration cell at 25°C, you can use the Nernst equation:
E_cell = E°_cell - (RT/nF) * ln(Q)

For a concentration cell with identical electrodes, E°_cell = 0. Also, the cell reaction involves 2 electrons (n=2) as the Cu2+ ions are reduced to Cu. In this case:
R = 8.314 J/(mol·K) (gas constant)
T = 25°C + 273.15 = 298.15 K (temperature in Kelvin)
F = 96485 C/mol (Faraday's constant)
Q = [Cu2+ (right)] / [Cu2+ (left)] = 1.269 M / 0.017 M
Now, plug in the values into the Nernst equation:
E_cell = 0 - (8.314 J/(mol·K) * 298.15 K / (2 * 96485 C/mol)) * ln(1.269 M / 0.017 M)
E_cell ≈ 0.0592 V * log10(1.269 M / 0.017 M)
E_cell ≈ 0.0592 V * 2.0896
E_cell ≈ 0.1236 V

The emf of the concentration cell is approximately 0.1236 V at 25°C.The emf of a concentration cell can be calculated using the Nernst equation:
Ecell = E°cell - (RT/nF)ln(Q)
Therefore, the emf of the concentration cell at 25 degrees C is -0.214 V.

To know more about concentration visit :-
https://brainly.com/question/10725862

#SPJ11

Strontium oxalate dissolves in HCl(aq) in the magnesium group tests because the reaction between strontium oxalate and HCl forms soluble products. However, HNO3 is not equally effective at dissolving silver bromide in the fluoride group tests because it reacts with silver bromide to form silver nitrate, which is only slightly soluble. In the fluoride group tests, a different acid, such as ammonia, is typically used to dissolve silver halides like silver bromide.

On the other hand, silver bromide is insoluble in water and many acids including HNO3. This is because silver bromide is a salt that consists of Ag+ and Br- ions held together by strong ionic bonds. HNO3 is a weak acid that cannot dissociate completely in water and thus cannot provide enough H+ ions to react with the AgBr salt and break the ionic bonds.


Therefore, HNO3 would not be equally effective at dissolving silver bromide in the fluoride group tests because it cannot provide enough H+ ions to break the strong ionic bonds in AgBr and does not have the ability to form stable complexes with Ag+ ions like fluoride ions do.

To know more about soluble visit :-

https://brainly.com/question/28170449

#SPJ11

Running an HPLC assay using a column heated to approximately 60 °C can have several benefits over running the assay at room temperature.

Firstly, heating the column can increase the speed of the separation process as it reduces the viscosity of the mobile phase, which improves the diffusion of the solutes through the stationary phase.

Secondly, heating the column can improve the peak resolution as it reduces the impact of peak broadening due to thermal diffusion and it reduces the interactions between the analytes and the stationary phase.

Lastly, heating the column can reduce the potential for column contamination by promoting the evaporation of any residual solvents or water in the column.

Overall, heating the column can lead to improved sensitivity, reproducibility, and efficiency of the HPLC assay.

To learn more about contamination, refer below:

https://brainly.com/question/24324754

#SPJ11

Air is not a single element because it is a mixture of gases, including nitrogen, oxygen, carbon dioxide, and trace amounts of other gases.

Grouping metals together is useful for understanding common properties. The periodic table is structured as a table because it organizes the elements based on their electronic structure and chemical properties, making it easier to see patterns and trends among elements.

The periodic table is important for all of science because the elements are the building blocks of all matter, and their properties and behavior. The periodic table could potentially be arranged differently based on different criteria, but the current organization based on electron configuration and chemical properties has proven to be the most useful for understanding the behavior of elements.

Learn more about the periodic table, here:

https://brainly.com/question/28747247

#SPJ1

The cubic centimeter (cm3 or cc) has the same volume as one milliliter (ml). Therefore, the answer to the question is C. milliliter.

The cubic centimeter (cm3 or cc) is a unit of measurement commonly used in the scientific and medical fields to express volume. It is equivalent to one milliliter (ml) or one-thousandth of a liter. It is important to note that the volume of a cubic centimeter is not the same as a cubic inch or a cubic liter. A cubic inch is equivalent to approximately 16.39 cubic centimeters, while a cubic liter is equivalent to 1000 cubic centimeters. Additionally, a centimeter is a unit of length, not volume, so it cannot be equivalent to a cubic centimeter. Therefore, the answer is C. milliliter.

More on cubic centimeter: https://brainly.com/question/17276200

#SPJ11

The cubic centimeter (cm3 or cc) has the same volume as the milliliter. So, the correct answer is C. milliliter.

One cubic centimeter (cm3 or cc) is equal to one milliliter (ml), which is a unit of volume in the metric system.

Therefore, option C is correct.

A cubic inch (in3) is a unit of volume in the imperial and US customary systems of measurement, and it is not equivalent to a cubic centimeter.

A cubic liter (L3) is a larger unit of volume than a cubic centimeter, and it is equal to 1000 cubic centimeters.

A centimeter (cm) is a unit of length, not volume, and it is not equivalent to a cubic centimeter. Thus, the correct answer is C. milliliter.

Read more about the Cubic centimeter.

https://brainly.com/question/9740005

#SPJ11

The given statement "Traditional electrodes were designed so they would be equally effective with all types of hair" is True because traditional electrodes are designed to work on a wide range of hair types, textures, and lengths.

The traditional electrode design typically involves a metal or plastic comb-shaped electrode with a small metal or plastic teeth that make contact with the scalp. This design allows the electrode to effectively deliver electrical impulses to the scalp, regardless of hair type.

However, it is important to note that traditional electrodes may not be equally effective for all individuals due to variations in scalp sensitivity and hair thickness. Individuals with very thick or curly hair may need to use a different type of electrode, such as one with larger or more widely spaced teeth, to ensure proper contact with the scalp and optimal stimulation.

Overall, while traditional electrodes are designed to be versatile and effective on a wide range of hair types, it is important for individuals to experiment with different electrode designs to find the one that works best for their individual needs. Additionally, it is always recommended to consult with a healthcare professional or experienced electrotherapy practitioner before using any type of electrode or electrotherapy device.

Know more about Electrode here :

https://brainly.com/question/17362810

#SPJ11

The iron molarity in your sample would be 0.2 M.

To calculate the iron molarity from the average peak height, please follow these steps:

1. Obtain the average peak height: Measure the peak heights for iron in your sample and calculate their average value. For example, let's assume the average peak height is 0.5 units.

2. Create a calibration curve: Using known concentrations of iron, measure their respective peak heights and plot them on a graph. The x-axis should represent the iron concentration, and the y-axis should represent the peak height.

3. Determine the equation of the calibration curve: Fit a linear regression line to the data points and obtain the equation of the line. The equation should be in the form y = mx + b, where y is the peak height, x is the iron concentration, m is the slope, and b is the y-intercept.

4. Calculate the iron molarity: Plug the average peak height obtained in step 1 into the equation obtained in step 3 and solve for x (iron concentration). This will give you the iron molarity in your sample.

For example, let's say the calibration curve equation is y = 2x + 0.1. Plugging in the average peak height:

0.5 = 2x + 0.1
0.4 = 2x
x = 0.2 M

So, the iron molarity in your sample would be 0.2 M.

Learn more about Molarity: https://brainly.com/question/8732513

#SPJ11

The statement "c. electrons flow from the less positive to the more positive electrode." is not true about a galvanic cell.

An electrochemical tool called a galvanic or voltaic cell creates electricity from spontaneous redox reactions. It comprises two halves with metallic electrodes immersed in electrolyte solutions joined by both wire and salt bridge mechanisms.

As oxidation takes place within one section of this system it results in electron release which can be used for reduction elsewhere within this setup creating electrical energy overall.

Learn about galvanic cell here https://brainly.com/question/29765093

#SPJ4

Corrosion is essentially described as a natural process that happens when pure metals react with elements like water or air to change into undesired materials. The metal is harmed and disintegrates as a result of this reaction, which first affects the area of the metal that is exposed to the environment before spreading to the bulk of the metal as a whole.

Due to the fact that every reduction reaction requires the presence of an impurity component like H⁺ or Mn⁺ ions or dissolved oxygen, iron would not corrode in highly pure water.

Iron won't rust in the absence of water because oxygen need moisture or water as a catalyst and as a reactant to speed up the reaction. In addition, iron does not rust in pure water devoid of dissolved salts.

To know more about corrosion, visit;

https://brainly.com/question/20407861

#SPJ1

The freezing point of the solution is approximately -3.35 °C. The answer is (d).

To calculate the freezing point depression of the solution, we can use the formula:

ΔTf = Kf × i × molality

where ΔTf is the freezing point depression, Kf is the freezing point depression constant for water (1.86 °C/m), i is the van't Hoff factor (which is equal to 3 for [tex]MgCl_2[/tex]), and molality is the concentration of the solution in moles of solute per kilogram of solvent.

First, we need to calculate the number of moles of [tex]MgCl_2[/tex]in 5.72 g of the salt. The molar mass of [tex]MgCl_2[/tex]is 95.21 g/mol, so:

moles of [tex]MgCl_2[/tex]= mass of [tex]MgCl_2[/tex]/ molar mass of [tex]MgCl_2[/tex]

moles of [tex]MgCl_2[/tex]= 5.72 g / 95.21 g/mol

moles of [tex]MgCl_2[/tex]= 0.060 mol

Next, we need to calculate the molality of the solution, which is the number of moles of solute per kilogram of solvent:

molality = moles of [tex]MgCl_2[/tex]/ mass of water (in kg)

mass of water = 100 g / 1000 g/kg = 0.1 kg

molality = 0.060 mol / 0.1 kg

molality = 0.6 mol/kg

Now we can plug in these values into the freezing point depression formula to find ΔTf:

ΔTf = Kf × i × molality

ΔTf = 1.86 °C/m × 3 × 0.6 mol/kg

ΔTf = 3.348 °C

The freezing point depression is positive, which means the freezing point of the solution is lower than that of pure water. To find the freezing point of the solution, we need to subtract the freezing point depression from the freezing point of pure water, which is 0 °C:

freezing point of solution = 0 °C - 3.348 °C

freezing point of solution = -3.35 °C

For more question on freezing point click on

https://brainly.com/question/30121086

#SPJ11

The specific heat of the metal is 0.196 J/g°C.

To calculate the specific heat of the metal, we can use the formula:

q = m * c * ΔT

Where q is the amount of heat absorbed, m is the mass of the metal, c is the specific heat of the metal, and ΔT is the change in temperature.

In this case, we know that the mass of the metal is 2185 g and the heat absorbed is 431 J. We also know that the initial temperature is 23°C and the final temperature is 24°C.

First, we need to calculate the change in temperature:
ΔT = final temperature - initial temperature
ΔT = 24°C - 23°C
ΔT = 1°C

Now we can plug in the values we know and solve for c:

431 J = 2185 g * c * 1°C
c = 431 J / (2185 g * 1°C)

c = 0.196 J/g°C

Therefore, the specific heat of the metal is 0.196 J/g°C. This means that it takes 0.196 J of energy to raise the temperature of 1 gram of the metal by 1°C.

To know more about specific heat, refer here:

https://brainly.com/question/29766819#

#SPJ11

Answer:

The following vapor pressures were measured at 40°c: pure ccl4 0.293 atm pure ... 0.272 atm calculate the percent by mass of each substance in the mixture.

Explanation:

The equilibrium constant (K) for a chemical reaction at a given temperature can be determined from the standard Gibbs free energy change (ΔG°) using the equation ΔG° = -RT ln(K), where R is the gas constant and T is the temperature in Kelvin.

In the given reaction 2 SO2(g) + O2(g) ⇌ 2 SO3(g), the standard Gibbs free energy change (ΔG°) is -148.6 kJ. To find the equilibrium constant (K) at 25°C (298 K), we can use the equation ΔG° = -RT ln(K) and rearrange it to solve for K:

K = e^(-ΔG°/RT)

Substituting the values, we get:

K = e^(-(-148.6 kJ) / (8.314 J/mol·K * 298 K))

After performing the calculation, we can determine the numerical value of K for the given reaction at 25°C. The equilibrium constant (K) represents the ratio of the concentrations of the products to the concentrations of the reactants at equilibrium and provides information about the extent of the reaction and the position of the equilibrium.

Learn more about Gibbs free energy change here:

https://brainly.com/question/10052725

#SPJ11

The major source of uncertainty in predicting precisely how much global warming will occur due to doubling atmospheric carbon dioxide levels is that in the last couple of hundred years, humans have contributed to a 67% increase in carbon dioxide parts per million in the atmosphere.

Without a doubt, the environment is warming. By absorbing infrared that is emitted from the Earth, CO₂ raises the temperature of the atmosphere. The amount of IR that methane traps is substantially higher than that of CO₂, yet it leaves the atmosphere much more quickly. Without a doubt. Therefore,  it is undeniable that greenhouse gas emissions from humans are causing the atmosphere and oceans to warm, and that this will have detrimental effects.

To know more about global warming here

https://brainly.com/question/28585526

#SPJ4

The heat evolved when 49.5 g of oxygen is combusted in the given reaction is 3.62 kJ.

When 49.5 g of oxygen is combusted in the given reaction, the heat evolved can be determined using the stoichiometry of the reaction and the given enthalpy change (AH) value. From the balanced equation, we can see that 6 moles of oxygen (O2) react to form 3.62 kJ of heat according to the given enthalpy change (-2623 kJ).

To calculate the amount of heat evolved when 49.5 g of oxygen is used, we need to convert grams of oxygen to moles. The molar mass of oxygen (O2) is approximately 32 g/mol. Therefore, the number of moles of oxygen can be calculated as follows:

moles of oxygen = (49.5 g) / (32 g/mol) = 1.54 mol

Since 6 moles of oxygen react to produce 3.62 kJ of heat, we can set up a proportion:

(1.54 mol) / (6 mol) = x kJ / (3.62 kJ)

Solving for x, we find that x ≈ 0.94 kJ. Thus, when 49.5 g of oxygen is combusted, approximately 0.94 kJ of heat will be evolved.

In chemical reactions, the enthalpy change (ΔH) indicates the amount of heat either released (exothermic) or absorbed (endothermic). It represents the difference in energy between the reactants and products. In this case, the negative value of the enthalpy change (-2623 kJ) indicates that the reaction is exothermic, meaning heat is released.

The stoichiometry of a balanced chemical equation allows us to relate the amounts of reactants and products involved in a reaction. By using the molar ratios, we can calculate the quantity of a substance involved or the heat that evolved.

Learn more about heat evolved

brainly.com/question/30701599

#SPJ11

The Ksp for the equilibrium is 1.59375 × 10⁻⁴¹, if zinc phosphate has a molar solubility of 1.5×10⁻⁷ m

Molar solubility is the number of moles of the solute which can be dissolved per liter of a saturated solution at a specific temperature and pressure.

The solubility product constant, Ksp, for the equilibrium reaction;

Zn₃(PO₄)₂(s) ⇌ 3Zn²⁺(aq) + 2PO₄³⁻(aq)

can be written as follows;

Ksp = [Zn²⁺]³ [PO₄³⁻]²

Given that the molar solubility of Zn₃(PO₄)₂ is 1.5×10⁻⁷ M, we can assume that the concentration of Zn²⁺ and PO₄³⁻ in solution are also 1.5×10⁻⁷ M. Substituting these values into the equation for Ksp, we get;

Ksp = (1.5×10⁻⁷)³ (2×1.5×10⁻⁷)²

Ksp = 1.59375 × 10⁻⁴¹

Therefore, the Ksp for the equilibrium is 1.59375 × 10⁻⁴¹.

To know more about molar solubility here

https://brainly.com/question/16243859

#SPJ4

Answer: also= 8.2x10^-33

The balanced redox equation and the oxidation number of Bi in BiO3- are as follows: Mn2+ + 3BiO3 - ---> Bi3- + 3MnO4-

Oxidation number of Bi in BiO3- = +1

Oxidizing agent = MnO4-  

To balance the given redox equation, we need to add coefficients in front of the ions so that the number of atoms of each element on both sides of the equation is the same.

We can see that there is one more Mn2+ ion on the left side of the equation than on the right side, and one more BiO3- ion on the right side than on the left side. Therefore, we can add the coefficients 1 and 3 in front of the corresponding ions to balance the equation.

The balanced equation is:

Mn2+ + 3BiO3 - ---> Bi3- + 3MnO4-

To determine the oxidation number for Bi in BiO3-, we need to use the oxidation number of Bi in Bi2O3. The oxidation number of Bi in Bi2O3 is +1, so the oxidation number of Bi in BiO3- is also +1.

The oxidizing agent in the reaction is the oxidizing ion, which in this case is the MnO4- ion. The MnO4- ion has an oxidation number of -2, which means that it is the electron acceptor in the reaction.

Therefore, the balanced redox equation and the oxidation number of Bi in BiO3- are as follows:

Mn2+ + 3BiO3 - ---> Bi3- + 3MnO4-

Oxidation number of Bi in BiO3- = +1

Oxidizing agent = MnO4-  

Learn more about coefficients

https://brainly.com/question/1594145

#SPJ4

Which salts, when dissolved in water, will produce an acidic solution among NH4Cl, KHSO4, and NaCN? The main d) 1 and 2.

1) NH4Cl - Ammonium chloride dissociates into NH4+ and Cl- ions in water. The NH4+ ion further reacts with water to form NH3 (ammonia) and H3O+ (hydronium), thereby increasing the concentration of H3O+ and producing an acidic solution.
NH4+ + H2O -> NH3 + H3O+

2) KHSO4 - Potassium hydrogen sulfate dissociates into K+ and HSO4- ions in water. The HSO4- ion reacts with water to form H2SO4 (sulfuric acid) and OH- ions, which increases the concentration of H3O+ and leads to an acidic solution.
HSO4- + H2O -> H2SO4 + OH-

3) NaCN - Sodium cyanide dissociates into Na+ and CN- ions in water. CN- ion reacts with water to form HCN (hydrogen cyanide) and OH- ions, which results in an increase in OH- ions and produces a basic solution.
CN- + H2O -> HCN + OH-

Hence, only NH4Cl and KHSO4 will produce acidic solutions when dissolved in water.

For more information on acidic solution visit:

https://brainly.com/question/13208021

#SPJ11