False. The relative humidity will decrease if the mixing ratio drops and the temperature remains unchanged.
Relative humidity is the ratio of the amount of water vapor present in the air to the maximum amount the air can hold at a given temperature, so if the amount of water vapor decreases (due to lower mixing ratio), the relative humidity decreases unless the temperature also decreases.
False. If the temperature remains unchanged and the mixing ratio drops, the relative humidity will decrease. This is because relative humidity is the ratio of the actual amount of water vapor in the air (mixing ratio) to the maximum amount of water vapor the air can hold at a specific temperature. If the mixing ratio decreases while temperature stays constant, the relative humidity will be lower.
To know more about Humidity click here .
brainly.com/question/22069910
#SPJ11
(Table 300-5) UF cable is used to supply power to a 120 volt 15 ampere GFCI protected circuit. If the cable is installed outdoors under the driveway of a one-family dwelling, the minimum cover requirement is _____ inches.
The minimum cover requirement for UF cable installed outdoors under the driveway of a one-family dwelling to supply power to a 120 volt 15 ampere GFCI protected circuit is 24 inches according to Table 300-5.
This ensures that the cable is adequately protected from damage and potential hazards.
The minimum cover requirement for UF cable. For a UF cable used to supply power to a 120 volt 15 ampere GFCI protected circuit, when installed outdoors under the driveway of a one-family dwelling, the minimum cover requirement according to Table 300-5 is 24 inches.
The minimum cover requirement for UF cable supplying power to a 120 volt 15 ampere GFCI protected circuit, when installed outdoors under the driveway of a one-family dwelling, is 24 inches.
Visit here to learn more about GFCI protected circuit:
brainly.com/question/30239193
#SPJ11
(368-12(2)) In general, the voltage limitation between conductors in a surface metal raceway shall not exceed _____ volts unless the metal has a thickness listed for higher voltage.
In general, the voltage limitation between conductors in a surface metal raceway shall not exceed 600 volts unless the metal has a thickness listed for higher voltage.
In general, the voltage limitation between conductors in a surface metal raceway shall not exceed _____ volts unless the metal has a thickness listed for higher voltage.
The voltage limitation between conductors in a surface metal raceway shall not exceed 600 volts unless the metal has a thickness listed for higher voltage.
Learn more about voltage limitation here;
https://brainly.com/question/23777621
#SPJ11
which of the following statements are correct? which of the following statements are correct? all applications of forces require contact between two objects. forces are measured in newtons. a force is a scalar. a force is a push or pull.
The correct statements are: forces are measured in newtons and a force is a push or pull.
1. All applications of forces require contact between two objects.
- Incorrect. There are non-contact forces, such as gravitational and magnetic forces, that do not require direct contact between objects.
2. Forces are measured in Newtons.
- Correct. The unit used to measure force is the Newton (N).
3. A force is a scalar.
- Incorrect. A force is a vector quantity, not a scalar. This means that it has both magnitude and direction.
4. A force is a push or pull.
- Correct. Forces are interactions that result in a push or pull on objects, causing them to change motion or remain stationary.
In summary, statements 2 and 4 are correct, while statements 1 and 3 are incorrect.
To learn more about force click here https://brainly.com/question/13191643
#SPJ11
A 33-kg girl climbs a 18-m rope in 27 s.
What is her average power?
The gravitational potential energy gained by the girl can be calculated as: PE = mgh
where m is the mass of the girl, g is the acceleration due to gravity (9.8 m/s^2), and h is the height climbed (18 m).
PE = (33 kg)(9.8 m/s^2)(18 m) = 5,662.4 J
The time taken to climb the rope is t = 27 s. Therefore, the average power (P) of the girl can be calculated as:
P = PE / t
P = 5,662.4 J / 27 s ≈ 209.34 W
Therefore, the average power of the girl is approximately 209.34 watts.
To calculate the average power, we use the formula:
Power = Work / time
where Work is the amount of work done, and time is the time it took to do the work.
To find the work done by the girl, we need to calculate the gravitational potential energy she gained by climbing the rope:
Potential Energy = mgh
where m is the mass of the girl, g is the acceleration due to gravity, and h is the height climbed.
Plugging in the values, we get:
Potential Energy = (33 kg) x (9.81 m/s^2) x (18 m) = 5,997.06 J
Now we can calculate the average power:
Power = Work / time = 5,997.06 J / 27 s = 222.11 W
Therefore, the girl's average power while climbing the rope is approximately 222 W.
To know more about work done
brainly.com/question/13662169
#SPJ11
What is the approximate time of death if the body temperature was 10°C (50°F)?
If the body temperature was 10°C, the approximate time of death would be between 12 and 36 hours, depending on the surroundings and other variables.
What time does death occur?However, it's crucial to note that the time of death can be influenced by several factors like the environment, clothing, and the person's physical state. The time of death can also be estimated by measuring the body temperature, also known as algor mortis.
After death, the body temperature decreases at a rate of roughly 1.5°C per hour, though this might change depending on the surroundings and other variables. It is impossible to pinpoint the exact time of death if the body temperature was 10°C, although it may indicate that death happened several hours earlier because the body temperature will continue to drop after death.
However, other techniques, like lividity, rigor mortis, and inspection of the stomach contents, are more accurate, hence it is not advised to utilize this method alone to establish the time of death. For a more precise estimation of the time of death, a forensic specialist should be consulted.
Learn more about time of death here:
https://brainly.com/question/16390042
#SPJ1
Where do the hydrogen and oxygen atoms come from that become part of the glucose molecule made during photosynthesis?
During photosynthesis, the hydrogen atoms come from water molecules that are split apart by light energy in the process called photolysis. The oxygen atoms, on the other hand, come from the same water molecules as the hydrogen atoms. They are released into the atmosphere as a by-product of photosynthesis. So, both the hydrogen and oxygen atoms that become part of the glucose molecule come from water molecules.
To know more about photosynthesis, click here:-
https://brainly.com/question/29764662
#SPJ11
Question 1 Marks: 1 The type of filter that is recommended for use at small communities and rural places is theChoose one answer. a. rapid sand filter b. pressure filter c. slow sand filter d. diatomaceous earth filter
The correct option is c. slow sand filterThe type of filter that is recommended for use in small communities and rural places is the slow sand filter.
This is because slow sand filters are effective at removing contaminants from water sources that are not heavily polluted and they do not require electricity or expensive equipment to operate, making them a cost-effective solution for these areas.
The type of filter recommended for use in small communities and rural places is: Slow sand filters are suitable for small communities and rural areas because they require less maintenance, have lower operating costs, and do not require chemicals for operation.
Learn more about diatomaceous earth here: brainly.com/question/30750966
#SPJ11
at steady state, a 1 m thick wall has a temperature difference (between the left and right surfaces) of capital delta t equals 5 k. if the wall's thermal conductivity is k equals 10 space fraction numerator w over denominator m k end fraction, what is the heat flux across this wall? (assume 1d conduction heat transfer.)
The magnitude of the heat flux across the wall is [tex]50 W/m^2[/tex] at steady state, a 1 m thick wall has a temperature difference.
To calculate the heat flux across the 1 m thick wall at steady state, we can use Fourier's Law of Heat Conduction. The formula is: q = -k * (dT/dx)
where q is the heat flux ([tex]W/m^2[/tex]), k is the thermal conductivity (10 W/m·K), dT is the temperature difference (5 K), and dx is the thickness of the wall (1 m).
Now, plug in the given values:
q = -10 * (5 K / 1 m)
q = [tex]-50 W/m^2[/tex]
Since we're considering 1D conduction heat transfer and the heat flux is negative, it means the heat is transferred from the higher temperature side to the lower temperature side.
To learn mote about heat flux click here https://brainly.com/question/30708042
#SPJ11
a large block of ice is being pushed on a frozen pond by layla and nadia. layla pushes the block to the right with a force of 40 n and nadia pushes the block to the left with a force of 70 n. what is the net force on the block of ice?
30N is the net force on the block of ice for a large block of ice is being pushed on a frozen pond by layla and nadia
The net force on the block of ice is the result of combining the forces pushing in opposite directions. Layla pushes to the right with a force of 40 N, while Nadia pushes to the left with a force of 70 N. To find the net force, we need to subtract the smaller force from the larger force, since they are in opposite directions.
When forces are in balance, there is no net force, hence there is no net force.
There is either no movement or steady movement when something is in balance.
Equal in size and directed in the opposite direction, balanced forces are. When forces are evenly distributed, motion remains unchanged.
So, the net force on the block of ice is:
70 N (Nadia's force) - 40 N (Layla's force) = 30 N
Therefore, the net force on the block of ice is 30 N to the left, since Nadia's force is greater than Layla's force.
Learn more about force here
https://brainly.com/question/15711576
#SPJ11
NO WRONG ANSWERS OR LINKS THEY WILL GET REPORTED 20 POINTS
Are Indoor Vertical Farms the Future of Agriculture
1 .What does Mr. Oda say the global population will be in 2050?
2. What does this mean for agricultural growth in the future?
3.How much food is wasted compared to what is produced?
4. What is indoor vertical farming?
5. Why is indoor vertical farming becoming more popular?
6. In what ways would indoor vertical farming make an environmental and societal impact as the global population increases?
On Indoor Vertical Farms the Future of Agriculture:
According to Mr. Oda, the global population will reach 10 billion by 2050.The growing population means that food production needs to increase by 70% in order to feed everyone.Approximately one-third of the food produced in the world is wasted.Indoor vertical farming is a method of growing crops in vertically stacked layers, using artificial lighting and environmental controls to optimize growth conditions.Indoor vertical farming is becoming more popular due to its ability to grow crops in urban areas, year-round, and with significantly less water and space than traditional farming methods.Indoor vertical farming could have several environmental and societal impacts, such as reducing transportation emissions, conserving water resources, and providing fresh, locally grown produce in urban areas. Why is indoor vertical farming necessary?Indoor vertical farming is necessary for several reasons. Firstly, it allows for year-round crop production in a controlled environment, which can increase crop yields and reduce the impact of climate change on agriculture.
Secondly, it can be done in urban areas, reducing the need for transportation of food over long distances, and providing fresh produce to urban populations. Additionally, it could provide new job opportunities and help address food insecurity in areas with limited access to fresh produce.
Find out more on indoor vertical farming here: https://brainly.com/question/17144968
#SPJ1
A neurologist researches reaction time by measuring how long it takes different people to catch a falling object. What is the level of measurement of the data? Select the correct answer below: Nominal Ordinal Interval Ratio
A neurologist researches reaction time by measuring how long it takes different people to catch a falling object. The level of measurement of the data is Interval.
Reaction time is a continuous variable that can be measured on a scale with equal intervals between values. In this case, the time taken to catch the falling object is likely to be measured in seconds or fractions of seconds, which constitutes an interval scale of measurement.
A nominal level of measurement is used for categorical data where the data can be sorted into distinct categories with no inherent order, such as gender or eye colour. The ordinal level of measurement is used for data that can be sorted into categories with a natural order, such as education level (high school, college, graduate). The ratio level of measurement is similar to interval measurement but with a true zero point, such as weight or height, where zero represents the absence of the attribute being measured.
Therefore the correct answer is interval.
To learn more about object, refer:-
https://brainly.com/question/12167131
#SPJ11
The level of measurement of the data collected by the neurologist in measuring reaction time is interval.
To determine the level of measurement, we need to evaluate whether the data meets the criteria for each level of measurement.
Nominal level data has categories that are mutually exclusive and exhaustive.
In this case, the data collected is not nominal since there are no categories that are mutually exclusive and exhaustive.
Ordinal level data has categories that have a natural order or ranking.
In this case, the data collected is not ordinal since there is no natural order or ranking of the time taken to catch a falling object.
Interval level data has a meaningful ordering or ranking of values, where the intervals between adjacent values are equal and meaningful.
In the case of the neurologist's research, the time taken by different people to catch a falling object has meaningful intervals that can be compared and analyzed.
Ratio level data has all the characteristics of interval data, but also has a true zero point, meaning that zero represents the complete absence of the variable being measured.
In this case, there is no true zero point for reaction time since even the fastest reaction time is not truly zero, as there is always some minimal time required for the brain to register the falling object and send a signal to the muscles to initiate the catch.
Based on the above analysis, the level of measurement of the data collected by the neurologist in measuring reaction time is interval.
To know more about level of measurement of the data :
https://brainly.com/question/20816026
#SPJ11
during alpha decay, a uranium-238 atom emits an alpha particle (a 4he nucleus, with a mass of 4.0015 amu). if the particle is emitted at a speed of 15,000 km/s, what is the debroglie wavelength of the particle?
The de Broglie wavelength of the emitted alpha particle is approximately 1.332 x[tex]10^{-14}[/tex] meters.
During alpha decay, a uranium-238 atom emits an alpha particle (4He nucleus) with a mass of 4.0015 amu. To calculate the de Broglie wavelength of the emitted particle traveling at 15,000 km/s, you can use the following equation:
λ = h / (m * v)
where λ is the de Broglie wavelength, h is the Planck constant (6.626 x [tex]10^{-34}[/tex]Js), m is the mass of the particle in kilograms, and v is the velocity in meters per second.
First, convert the mass from amu to kilograms: 1 amu = 1.66054 x [tex]10^{-27}[/tex] kg
m = 4.0015 amu * (1.66054 x[tex]10^{-27}[/tex] kg/amu) ≈ 6.644 x [tex]10^{-27}[/tex]kg
Next, convert the velocity from km/s to m/s: 1 km = 1,000 m
v = 15,000 km/s * (1,000 m/km) = 1.5 x [tex]10^{7}[/tex] m/s
Now, you can calculate the de Broglie wavelength:
λ = (6.626 x [tex]10^{-34}[/tex] Js) / (6.644 x [tex]10^{-27}[/tex] kg * 1.5 x [tex]10^{7}[/tex] m/s)
λ ≈ 1.332 x [tex]10^{-14}[/tex] m
Learn more about wavelength here: https://brainly.com/question/31143857
#SPJ11
When 115 V is applied across a wire of radius 0.30 mm and length 10 m, the magnitude of the current density is 1.4x108 A/m2. Find the resistivity of the wire.
The resistivity of the wire is 2.7 x 10^-8 Ωm.
The resistivity of the wire is found to be 2.7 x 10^-8 Ωm by calculating the current flowing through it using the current density equation, multiplying the current density of 1.4x10^8 A/m^2 by the cross-sectional area of the wire, calculating the resistance of the wire using Ohm's law, and calculating the resistivity of the wire using the equation ρ = RA/L, where R is the resistance, A is the cross-sectional area of the wire, and L is its length, and substituting the values we have calculated.
To learn more about resistivity, click here:
https://brainly.com/question/29427458
#SPJ11
The suction line is known as the ___ line in an air-to-air heat pump split system.a. vaporb. liquidc. transientd. gas
The suction line is known as the vapour line in an air-to-air heat pump split system.
The vapour line allows the connection between the ship tank's vapour space and the shore tank's vapour space. The vapour spaces of ship and shore tanks will always be in equilibrium. We use the vapour line with the purpose that there should not be any release of cargo vapours into the atmosphere. The vent pipes from cargo oil tanks. They are led to pressure/vacuum valves which are usually mounted on standpipes some distance above the deck.
Learn more about equilibrium here: https://brainly.com/question/30807709
#SPJ11
The density of mercury is 13.6 g/cm3. What volume (in quarts) is occupied by 100. g ofHg? (1 L = 1.06 qt)A) 144 qt B) 7.35 qt C) 7.79 qt D) 7.79 × 10-3 qt E) 1.44 × 10-4 qt
The closest answer to this is 7.79 × [tex]10^{-3}[/tex] qt (option D).
The density of mercury is 13.6 g/[tex]cm^{3}[/tex]. To find the volume occupied by 100 g of Hg, first, we need to calculate the volume in cubic centimeters ([tex]cm^{3}[/tex]
) using the formula:
Volume ([tex]cm^{3}[/tex] = mass (g) / density (g/[tex]cm^{3}[/tex])
Volume ([tex]cm^{3}[/tex] = 100 g / 13.6 g/[tex]cm^{3}[/tex] = 7.35 [tex]cm^{3}[/tex]
Now, we need to convert the volume from cubic centimeters to quarts using the given conversion factor (1 L = 1.06 qt). First, convert [tex]cm^{3}[/tex]to liters (1 L = 1000 [tex]cm^{3}[/tex]):
Volume (L) = 7.35 cm3 * (1 L / 1000 [tex]cm^{3}[/tex]) = 0.00735 L
Now, convert liters to quarts:
Volume (qt) = 0.00735 L * (1.06 qt / 1 L) ≈ 0.00779 qt
Therefore the answer is answer is 7.79 × [tex]10^{-3}[/tex] qt
Learn more about density here: https://brainly.com/question/29775886
#SPJ11
Given a capacitor charged by connecting the two conductors to opposite terminals of a battery.
The potential difference (Vab) between the conductors is equal to...
The potential difference (Vab) between the conductors is equal to the electromotive force (EMF) of the battery.
When a capacitor is charged by connecting its two conductors to opposite terminals of a battery, the battery acts as a source of electrical energy, which causes the buildup of charge on the plates of the capacitor.
The potential difference (Vab) between the conductors of the capacitor is equal to the amount of electrical energy stored in the capacitor per unit of charge, which is equivalent to the electromotive force (EMF) of the battery. Therefore, the potential difference (Vab) is equal to the voltage of the battery, which is the maximum potential difference that can be obtained across the capacitor.
To know more about capacitor, here
https://brainly.com/question/17176550
#SPJ4
Question 71
The disposal of used tires presents a problem but shredded tires may be used as a. a source of heat for homes
b. fuel for industries
c. an asphalt additive to reduce pavement cracking
d. a supplemental fuel for incinerators
The disposal of used tires is indeed an issue due to their non-biodegradable nature and the large volume they occupy in landfills. However, shredded tires can provide various environmentally friendly and practical solutions.
Option A, using shredded tires as a source of heat for homes, is not the most common or efficient use of this material. Instead, options B, C, and D offer more feasible alternatives.
Option B, using shredded tires as fuel for industries, is a viable option. The high energy content of tires makes them suitable for use as a supplementary fuel in industries such as cement manufacturing, where they can replace traditional fossil fuels like coal.
Option C, using shredded tires as an asphalt additive to reduce pavement cracking, is another effective solution. The incorporation of shredded tires in asphalt mixtures enhances the durability and resistance of the pavement, minimizing the formation of cracks and prolonging its lifespan.
Option D, using shredded tires as supplemental fuel for incinerators, is a practical choice. In waste-to-energy incineration plants, the high calorific value of tires contributes to the generation of heat and electricity, reducing the demand for conventional energy sources.
In summary, while shredded tires may not be suitable as a direct source of heat for homes, they can serve as a valuable resource in industries, asphalt mixtures, and waste-to-energy incineration plants, addressing the disposal problem and providing sustainable alternatives to traditional materials and fuels.
For more information on shredded tires see:
https://brainly.com/question/29892098
#SPJ11
Question 38
Considered by many as the source of greatest public exposure related to nuclear power production is:
a. Power plant emissions
b. Leakage from power plants
c. Uranium mill tailings
d. Radon gas emissions
The correct answer is d. Radon gas emissions. Radon is a radioactive gas that can seep into homes and buildings from the ground and rocks beneath them.
It is a naturally occurring element in uranium deposits and is released during the process of nuclear power production. Radon exposure is a significant concern as it is the second leading cause of lung cancer after smoking. The greatest source of public exposure related to nuclear power production is radiation emitted from power plants. This radiation can come from a variety of sources, including the processing of uranium and plutonium fuel, the operation of reactors, and the disposal of nuclear waste. Nuclear power plants are required to meet strict safety standards and emit only a small amount of radiation into the environment.
To learn more about power plants click here https://brainly.com/question/14314816
#SPJ11
Terminal Rating(110-14(C)(1): What is the minimum size THHN conductor required for a 150 ampere circuit breaker or fuse? Be sure to comply with the requirements of Section 110-14(C)(2).
According to Terminal Rating (110-14(C)(1)), the minimum size THHN conductor required for a 150 ampere circuit breaker or fuse is 1/0 AWG.
However, it is important to comply with the requirements of Section 110-14(C)(2), which states that the conductor must be sized to carry at least 125% of the continuous load or 100% of the non-continuous load. Therefore, the actual minimum size THHN conductor required for a 150 ampere circuit breaker or fuse would be calculated as follows:
Continuous Load = 150 amperes
125% of Continuous Load = 1.25 x 150 = 187.5 amperes
Minimum THHN Conductor Size = 1/0 AWG (satisfies 187.5 amperes)
So, to meet the requirements of both Terminal Rating (110-14(C)(1)) and Section 110-14(C)(2), the minimum size THHN conductor required for a 150 ampere circuit breaker or fuse is 1/0 AWG.
To know more about Terminal Rating (110-14(C)(1)), please click on:
https://brainly.com/question/31566499
#SPJ11
the heating element of a hair dryer dissipates 1500 w when connected to a 160 v outlet. part a what is its resistance? express your answer with the appropriate units.
The heating element of a hair dryer dissipates 1500 w when connected to a 160 v outlet. The resistance of the heating element of a hair dryer is 17.07 ohms.
We can use Ohm's law to find the resistance of the heating element of a hair dryer. Ohm's law states that the resistance of a conductor is equal to the voltage across it divided by the current flowing through it.
In this case, we know that the power dissipated by the heating element is 1500 W and the voltage across it is 160 V. We can use the formula for power, which is power = voltage x current, to find the current flowing through the heating element.
1500 W = 160 V x current
Solving for current, we get:
Current = 9.375 A
Now we can use Ohm's law to find the resistance:
Resistance = Voltage / Current
Resistance = 160 V / 9.375 A
Resistance = 17.07 ohms (rounded to two decimal places)
Therefore, the resistance of the heating element of a hair dryer is 17.07 ohms, when connected to a 160 V outlet.
Learn more about Ohm's law here:
https://brainly.com/question/1247379
#SPJ11
a 98.8 kg weight-watcher wishes to climb a mountain to work off the equivalent of a large piece of chocolate cake rated at 715 (food) calories. how high must the person climb? the acceleration due to gravity is 9.8 m/s 2 and 1 food calorie is 103 calories. answer in units of km.
First, we need to convert the food calories into regular calories by multiplying by 103: 715 x 103 = 73,645 calories.
Next, we need to determine how much work the weight-watcher needs to do to burn off those calories. We can use the formula: work = force x distance, where force = mass x gravity and distance is the height the person needs to climb.
So, work = (98.8 kg)(9.8 m/s^2)(distance), We know that the work required to burn off 73,645 calories is equivalent to the work done by climbing a certain height, so we can set these two expressions equal to each other: work = 73,645 calories .
(98.8 kg)(9.8 m/s^2)(distance) = 73,645, Simplifying and solving for distance: distance = 73,645 / (98.8 x 9.8)
distance = 75.02 meters, Finally, we convert meters to kilometers: 75.02 m = 0.07502 km
So the weight-watcher needs to climb approximately 0.075 km to burn off the equivalent of a large piece of chocolate cake.
To know more about force click here
brainly.com/question/29044739
#SPJ11
a front-wheel drive car has tires that are driven by the motor only on the front tires. the rear tires just hold up the back of the car. when the speed of a front-wheel-drive car is increasing on a horizontal road, what is the direction of the frictional force on the tires?
The direction of the frictional force on the tires of a front-wheel-drive car as the speed increases on a horizontal road is opposite to the direction of the car's motion.
This is because the tires need to grip the road surface to provide the necessary traction to move the car forward, and the frictional force acts in the opposite direction to the movement of the car.
The amount of frictional force depends on several factors such as the weight of the car, the quality of the tires, the road conditions, and the speed of the car. In a front-wheel drive car, when the speed is increasing on a horizontal road, the direction of the frictional force on the front tires is forward, as they provide the necessary traction for acceleration.
On the rear tires, the frictional force acts in the opposite direction, or backward, as they resist the forward motion while supporting the weight of the car.
To learn more about frictional force click here
brainly.com/question/30280752
#SPJ11
Describe two conditions that can affect friction and traction.What happens to the handling of a car when there is a loss of friction and traction
a. Two conditions that can affect friction and traction are the type of surface and the presence of contaminants.
b. Loss of friction and traction can cause a car to slide, skid, or lose control.
Friction and traction are crucial for vehicle handling and control. Two conditions that can affect friction and traction are the surface condition and the tire condition.
Wet, icy, or uneven road surfaces can decrease friction and traction, while worn or improperly inflated tires can also reduce the ability to maintain traction.
Loss of friction and traction can result in a variety of handling issues, such as difficulty steering, reduced braking ability, and increased risk of skidding or sliding.
This can be particularly dangerous in adverse weather conditions or during sudden stops or turns, making it important for drivers to maintain their vehicles properly and adjust their driving habits to match the current road conditions.
Learn more about friction and traction at
https://brainly.com/question/29760637
#SPJ4
A cross-connection means?
a. Four pipelines tied together
b. A T-shaped tool
c. A connection between potable water and "unapproved" water supplies
d. A connection between two or more pressure zones
A cross-connection is a link between "unapproved" water sources and potable water sources. Hence option C is correct.
A cross-connection in plumbing is a connection between a system that provides potable water and any other system or source that provides non-potable water or other substances.
Cross-connections could result in health risks for users by allowing pollutants or toxins to enter the potable water system. To safeguard the public water supply, cross-connections must be located, deleted, or managed by the installation of backflow protection devices.
So, the correct answer is option C that says, "A connection between potable water and unapproved water supplies."
To know more about cross-connection, visit,
https://brainly.com/question/29488259
#SPJ4
explain how the tension force gets transmitted along from one end of a string to the other. does the amount of force gets transmitted depends on how elastic or stretchable the string is
The tension force gets transmitted along a string and how its elasticity affects the transmission.
When a force is applied to one end of a string, the tension force is created.
Tension force is the force that acts along the string, pulling it tight.
Tension force gets transmitted from one end to the other:
1. Apply a force to one end of the string, stretching it.
2. The string's elastic properties resist the stretching, creating tension.
3. This tension force is transmitted along the string as each part of the string pulls on the adjacent part.
4. The force continues to propagate along the string until it reaches the other end, where it either gets absorbed or causes movement if it's not fixed in place.
The amount of force transmitted depends on how elastic or stretchable the string .
If the string is more elastic, it will stretch more easily, and the tension force may be reduced as the string extends.
Conversely, if the string is less elastic, it will not stretch as much, leading to a higher tension force.
The key is that the force is transmitted along the entire string regardless of its elasticity; however, the elasticity affects the magnitude of the tension force.
To know more about tension force visit link :
https://brainly.com/question/31320838
#SPJ11
Switches made out of semiconductors made computers possible, but lately when it comes to high tech,
there's a new family on the block, the __________ _____________, 15 elements located near the
bottom of the table.
Switches made out of semiconductors made computers possible, but lately, when it comes to high tech, there's a new family on the block, the "rare earth elements," which are 15 elements located near the bottom of the periodic table.
These elements play a crucial role in modern technologies and have unique properties that make them essential for various applications. It's worth noting that rare earth elements are not typically used to make switches, but rather they are used in a variety of high-tech applications, including electronics, magnets, batteries, and more. While semiconductors made of silicon are still widely used in computer technology, rare earth elements have become increasingly important in a variety of high-tech applications due to their unique magnetic and optical properties. They are used in products such as wind turbines, electric vehicles, smartphones, and more.
Learn more about semiconductors here:
https://brainly.com/question/19618939
#SPJ11
What information must be on a warming tag attached to a locked-out switch?
a. Directions for removing the tag
b. Name of the nearest physician to call in case of an emergency
c. Signature of the person who locked out the switch and who will remove it
d. Time to unlock the switch
A warning tag attached to a locked-out switch should contain the following information: c. Signature of the person who locked out the switch and who will remove it. This ensures proper identification and responsibility for the lockout process, promoting safety and accountability in the workplace.
A warming tag is a type of tag that is attached to a locked-out switch. According to the Occupational Safety and Health Administration (OSHA), a warming tag attached to a locked-out switch should contain the signature of the person who locked out the switch and who will remove it.
Find out more about warning tag
brainly.com/question/28097783
#SPJ11
What information about an axon is required to calculate the current associated with an NCV pulse? Foundational Concept: 4 Complex living organisms transport materials, sense their environment, process signals, and respond to changes using processes understood in terms of physical principles Content Category: 4C Electrochemistry and electrical circuits and their elements Scientific Inquiry and Reasoning Skill: 1 Knowledge of Scientific Concepts and Principles Discipline: Physics O A. Conductivity, resistivity, and length O B. Potential, conductivity, and radius C. Potential, resistivity, and radius OD. Potential, resistance per unit length, and length This is a Physics question that falls under content category "Electrochemistry and electrical circuits and their elements." The answer to this question is D. This is a question about Ohm's Law, I- VIR. To determine R, the resistance per unit length, the length, and the potential V are needed. This question requires Knowledge of Scientifi
To calculate the current associated with an NCV pulse, we need to know the information about an axon's potential, resistance per unit length, and length.
This is because electrical signal travel through axons, which can be modeled as electrical circuits. Ohm's Law, I = V/R, can be applied to calculate the current, where V is the potential difference and R is the resistance per unit length of the axon. The length of the axon is also needed to determine the overall resistance. Therefore, understanding the electrical properties of axons, such as their potential and resistance, is crucial in calculating the current associated with an NCV pulse.
learn more about electrical signal refer: https://brainly.com/question/4523077
#SPJ11
(Table 310-15(b)(3a)): A raceway contains eight current-carrying conductors. What size conductor is required to feed a 21 ampere noncontinuous lighting load? The overcurrent protection device is rated 30 ampere.
A #10 copper or #8 aluminum conductor would be appropriate for this application.
To determine the size of the conductor required to feed a 21 ampere noncontinuous lighting load through a raceway containing eight current-carrying conductors, we need to consider the ampacity derating factor. According to NEC Table 310-16, when eight conductors are bundled together, the ampacity of each conductor is derated to 80% of its value. Therefore, the minimum ampacity required for the conductor is:
(21 amps) / (0.8) = 26.25 amps
Based on NEC Table 310-16, the minimum conductor size required for a 26.25-ampere load with a 30-ampere overcurrent protection device is #10 AWG copper or #8 AWG aluminum. Therefore, a #10 copper or #8 aluminum conductor would be appropriate for this application.
Learn more about aluminum conductor
https://brainly.com/question/15119400
#SPJ4
Full Question : (Table 310-15(b)(3a)): A raceway contains eight current-carrying conductors. What size conductor is required to feed a 21 ampere noncontinuous lighting load? The overcurrent protection device is rated 30 ampere.
Table image attached
Which statement does NOT describe a relationship shown in the food web
The statement is Rabbits consume shrubs and are parasites of grasses.
What three relationships do food webs have for feeding?Consumers can be distinguished based on where they are in the food chain: first order (primary) consumers consume producers; second order (secondary) consumers consume primary consumers; third order (tertiary) consumers consume secondary; and so on.
A food web contains how many different types of relationships?Trophic levels refer to the various feeding positions within a food chain or web. Producers make up the first trophic level, followed by primary consumers, secondary consumers, and so forth. A food chain or web typically only has four or five trophic levels.
To know more about the food web visit:
https://brainly.com/question/4656320
#SPJ1
Complete question;-
Which statement does NOT describe a relationship shown in the food web?
A Elk are prey for mountain lions.
B Mice are herbivores that consume grasses and are preyed on by snakes.
C Owls prey on rabbits and frogs.
D Rabbits consume shrubs and are parasites of grasses.
PLEASE HELP