Using the Ideal Gas equation, if the number of moles is constant, as pressure and volume increase temperature will __________.

Answer:

The CCl4 gas would need to be heated to -178.7 °C to have a volume of 2.00 liters at 250 °C.

Step-by-step explanation:

First, we need to calculate the number of moles of CCl4:

[tex]\sf:\implies n = \dfrac{m}{M}[/tex]

[tex]\sf:\implies n = \dfrac{75.0\: g}{154.0\: g/mol}[/tex]

[tex]\sf:\implies n = 0.487\: moles[/tex]

Next, we can use the ideal gas law to solve for the temperature:

[tex]\sf\qquad\dashrightarrow PV = nRT[/tex]

where:

We need to convert the given temperature of 250 °C to Kelvin:

[tex]\sf:\implies T = 250 ^{\circ}C + 273.15[/tex]

[tex]\sf:\implies T = 523.15\: K[/tex]

Now we can plug in the values and solve for T:

[tex]\sf:\implies (1\: atm)(2.00\: L) = (0.487\: mol)(0.08206\: L\cdot atm/mol\cdot K)T[/tex]

[tex]\sf:\implies T = \dfrac{(1\: atm)(2.00\: L)}{(0.487\: mol)(0.08206\: L\cdot atm/mol\cdot K)}[/tex]

[tex]\sf:\implies T = 94.5\: K[/tex]

Finally, we need to convert the temperature back to Celsius:

[tex]\sf:\implies T = 94.5\: K - 273.15[/tex]

[tex]\sf:\implies \boxed{\bold{\:\:T = -178.7 ^{\circ}C\:\:}}\:\:\:\green{\checkmark}[/tex]

Therefore, the CCl4 gas would need to be heated to -178.7 °C to have a volume of 2.00 liters at 250 °C.

Greetings! ZenZebra at your service, hope it helps! <33

Answer:

If a 0.5 mL air bubble is present in the tip of a burette, the initial reading will be too high by 0.5 mL. If the air bubble is dislodged during the dispensing of the samples, the final reading will be too low by 0.5 mL. This will result in a systematic error in the volume measurements.

To calculate the percent error in the volume measurements, we can use the formula:

% error = (systematic error / true value) x 100

For a 5-mL sample, the true value is 5 mL. If the air bubble is dislodged, the measured volume will be 4.5 mL, resulting in a systematic error of 0.5 mL. Therefore, the percent error is:

% error = (0.5 / 5) x 100 = 10%

For a 20-mL sample, the true value is 20 mL. If the air bubble is dislodged, the measured volume will be 19.5 mL, resulting in a systematic error of 0.5 mL. Therefore, the percent error is:

% error = (0.5 / 20) x 100 = 2.5%

For a 25-mL sample, the true value is 25 mL. If the air bubble is dislodged, the measured volume will be 24.5 mL, resulting in a systematic error of 0.5 mL. Therefore, the percent error is:

% error = (0.5 / 25) x 100 = 2%

So, the percent error in the volume measurements will be higher for smaller samples, and lower for larger samples.

The percent error for a 5 mL sample is 10%, for a 20 mL sample is 2.5%, and for a 25 mL sample is 2%.

The percent error can be calculated using the formula:

Percent Error = ((Actual Value - Experimental Value) / Actual Value)×100%

In this case, the actual value is the volume of the sample (5 mL, 20 mL, or 25 mL) and the experimental value is the volume obtained if the air bubble is dislodged.

The percent error for a 5 mL sample would be:

Percent Error = ((5 mL - 4.5 mL) / 5 mL ) ×100% = 10%

The percent error for a 20 mL sample would be:

Percent Error =( (20 mL - 19.5 mL) / 20 mL) ×100% = 2.5%

The percent error for a 25 mL sample would be:

Percent Error = ((25 mL - 24.5 mL) / 25 mL) × 100% = 2%

https://brainly.com/question/29107960

#SPJ2

Total, 2 moles of iron (II) nitrate would be needed to produce a 4 moles of lithium nitrate.

The balanced chemical equation for the reaction is;

2Li + 1Fe(NO₃)₂ → 1Fe + 2LiNO₃

From this equation, we can see that 2 moles of lithium nitrate are produced for every 1 mole of iron (II) nitrate used.

To determine how many moles of iron (II) nitrate are needed to produce 4 moles of lithium nitrate, we can use the mole ratio from the balanced equation;

moles of LiNO₃ = 4

moles of Fe(NO₃)₂ = (4 mol LiNO₃) x (1 mol Fe(NO₃)₂ / 2 mol LiNO₃)

= 2 mol Fe(NO₃)₂

Therefore, 2 moles of iron (II) nitrate is needed to produce 4 moles of lithium nitrate.

To know more about iron (II) nitrate here

https://brainly.com/question/31428625

#SPJ1

The amount of dry solute it would take to prepare 118 mL of 0.105 M NaNO3 is 1.05g.

The mass of a substance can be calculated by multiplying the number of moles in the substance by its molar mass as follows:

mass = no of moles × molar mass

However, the number of moles it took to prepare 118 mL of 0.105 M NaNO3 must be calculated as follows;

no of moles = 0.105 × 0.118 = 0.0124 moles

molar mass of sodium nitrate = 85g/mol

mass = 85g/mol × 0.0124 moles = 1.05g

Learn more about mass at: https://brainly.com/question/13320535

#SPJ1

The depth of the Grand Canyon at the spot where you can hear your echo 5.2 seconds after you shout is 884 meters.

The equation to find the distance from speed and time is:

distance = speed x time

In this problem, we are given the speed of sound (340 m/s) and the time it takes for the sound to travel to the bottom of the canyon and back (5.2 s). To find the distance from the top of the canyon to the bottom, we can use the above equation:

distance = speed x time = 340 m/s x 5.2 s = 1768 m

However, this distance represents the total distance traveled by the sound wave, which includes the distance from the top of the canyon to the bottom and back to the top. Since we are only interested in the depth of the canyon, we need to divide the total distance by two:

depth of canyon = distance / 2 = 1768 m / 2 = 884 m

Therefore, the depth of the Grand Canyon at the spot where you can hear your echo 5.2 seconds after you shout is 884 meters.

learn more about distance here

https://brainly.com/question/26046491

#SPJ1

The moles of the ammonia that is produced is 3.33 moles.

Stoichiometry is an important tool in chemical analysis, and it is used in a wide range of industries, including pharmaceuticals, materials science, and environmental science.

The balanced reaction equation in this case can be given as;

[tex]N_{2} (g)+3H_{2} (g)--- > 2NH_{3} (g)[/tex]

If 3 moles of hydrogen produces 2 moles of ammonia

5 moles of hydrogen will produce 5 * 2/3

= 3.33 moles

Thus we have 3.33 moles of ammonia.

Learn more about number of moles:https://brainly.com/question/31597231

#SPJ1

The new temperature of a sample of gas initially at 0°C and contains 100L is 546K.

The temperature of a gas can be calculated using the Charles' law equation as follows:

V₁/T₁ = V₂T₂

Where;

According to this question, the volume of a sample of a gas at 0°C is 100 liters. If the volume of the gas is increased to 200 liters at constant pressure, the new temperature is as follows:

100/273 = 200/T₂

200 × 273 = 100T₂

T₂ = 546K

Learn more about temperature at: https://brainly.com/question/15354399

#SPJ1

There are 1 lone pairs of electrons are in the ion OH⁻

Since oxygen creates two bonds, we know that two electrons are required to create those two bonds. There are now just two electron pairs remaining that are not involved in bonding. Oxygen thus contains two lone pairs.

The O and H atoms are connected by a solitary covalent link. The oxygen atom has a net -1 charge, which normally manifests as the whole charge on the OH- ion. On the O atom in the OH- Lewis structure, there exist lone electron pairs.

To know more about electrons visit:-

https://brainly.com/question/28977387

#SPJ1

Two alkenes may be produced when sodium ethoxide is used to treat 2-Bromo-3-methylbutane in ethanol. Saytzeff's rule governs the reaction pathway, leading to the formation of 2 methyl 2 butene as the main product, which is a more substituted alkene.

Inorganic synthesis uses sodium ethoxide, 21% w/w in ethanol, as a powerful base. It is used in a variety of chemical processes, including esterification, alkoxylation, condensation, and etherification. It participates actively in the Wolf-Kishner reduction, Stobbe reaction, and Claisen condensation.

Because ethoxide ions are Brnsted-Lowry bases and remove hydrogen ions from water molecules to form hydroxide ions, which raise the pH, the solution is extremely alkaline.

learn more about sodium ethoxide

https://brainly.com/question/13062423

#SPJ1

The volume (in liters) of ammonia, NH₃ produced from the reaction is 127 liters (option C)

First, we shall determine the mole in 17 g of H₂. Details below:

Mole = mass / molar mass

Mole of H₂ = 17/ 2

Mole of H₂ = 8.5 moles

Next, we shall determine the volume of H₂. Details below:

1 mole of hydrogen gas, H₂ = 22.4 Liters

Therefore,

8.5 moles of hydrogen gas, H₂ = (1.24 mole × 22.4 Liters) / 1 mole

8.5 moles of hydrogen gas = 190.4 liters

Finally, we shall determine the volume of ammonia, NH₃ produced. This is shown below:

N₂(g) + 3H₂(g) -> 2NH₃(g)

From the above equtaion,

3 liters of H₂ reacted with 2 liters of NH₃

Therefore

190.4 liters of H₂ will react = (190.4 liters × 2 liters) / 3 liters = 127 liters of NH₃

Thus, from the above illustration, we can conclude that the volume of ammonia, NH₃ produced  is 127 liters (option C)

Learn more about volume:

https://brainly.com/question/9614052

#SPJ1

A: Polar Attraction, because water molecules have a slightly positive charge on one end and a slightly negative charge on the other end, which causes them to be attracted to each other due to electrostatic forces.

Polar attraction is the attraction between two polar molecules. Polar molecules contain atoms with slightly different charges, resulting in a slightly positive end and a slightly negative end of the molecule. The attractive force that occurs between two polar molecules is the result of the positively charged end of one molecule being attracted to the negatively charged end of the other molecule. This type of attraction is known as a dipole-dipole interaction.

Electrostatic forces are forces of attraction or repulsion between particles that are caused by their electrical charge. Electrically charged particles are either positively or negatively charged, and they exert a force on each other that is proportional to the magnitude of their charges, and inversely proportional to the square of the distance between them. Electrostatic forces can be used to explain phenomena such as the attraction of dust particles to surfaces and the clustering of ions in a solution.

To know more about dipole-dipole interaction, visit:

https://brainly.com/question/7545068

#SPJ1

The running pressure of the HPLC procedure in torr is approximately 2068.2687 torr.

What is Chromatography?

Chromatography is a technique used to separate, identify, and analyze the components of a mixture based on their differential affinities to a stationary phase and a mobile phase. It is widely used in chemistry, biochemistry, pharmaceuticals, environmental science, forensics, and other fields for purification, separation, and analysis of chemical compounds.

To convert pressure from pascals (Pa) to torr, we can use the following conversion:

1 torr = 101325 Pa

So, to convert the pressure from pascals to torr, we can divide the pressure in pascals by 101325.

Given:

Pressure in pascals (Pa) = 2.09 × [tex]10^{8}[/tex] Pa

Using the conversion factor:

Pressure in torr = (2.09 × [tex]10^{8}[/tex]Pa) / 101325 Pa/torr

Calculating the numerical value in torr:

Pressure in torr = 2068.2687 torr (rounded to four decimal places)

Learn more about Chromatography from the given link

https://brainly.com/question/1394204

#SPJ1

Three patterns that are true regarding seasons on Earth are: 1. Seasons are caused by the tilt of Earth's axis. 2. Seasons are opposite in the Northern and Southern Hemispheres. 3. Seasons are characterized by changes in temperature and weather patterns.

As Earth orbits around the sun, different parts of the planet receive varying amounts of sunlight depending on their angle to the sun.

When it is summer in the Northern Hemisphere, it is winter in the Southern Hemisphere, and vice versa.

For example, summer is typically associated with warm temperatures, longer days, and increased humidity, while winter is associated with colder temperatures, shorter days, and often snow or rain.

To know more about weather patterns, here

brainly.com/question/28789144

#SPJ1

Show a greater conductivity than the covalent compound. This is because of the existence of strong electrostatic forces between the ions of the ionic compounds.

A force is an external agent capable of changing a body's state of rest or motion. It has a magnitude and a direction.A force is not something that an object contains or 'has in it'. A force is exerted on one object by another. The idea of a force is not limited to living things or non-living things.

it is formed by the loss or gain of an electron by an atom. Ions are of two types: cations and anions. For example, A sodium ion (Na+ ) is formed when a sodium atom loses one electron.

To know more about forces visit :

https://brainly.com/question/13191643

#SPJ1

NaOH is a base through all 3 definitions of base: Arrhenius, Bronsted-Lowry, and Lewis.

Arrhenius

An Arrhenius base is defined as a compound that increases the OH⁻ concentration in an aqueous solution. In other words, Arrhenius bases are compounds that have an OH⁻ ion. NaOH does dissolve into Na⁺ + OH⁻, so it will increase the OH⁻ of a solution. This means the compound is an Arrhenius base.

Bronsted-Lowry

Bronsted-Lowry bases are defined as a species that can accept a proton. Remember that a proton can be shown as H⁺. As stated above, NaOH dissolves into Na⁺ + OH⁻. In this form, the OH⁻ can accept the H⁺ to create H₂O. Thus, NaOH is a Bronsted-Lowry base.

Lewis Base

Lewis bases are compounds that can donate an electron pair. The O in dissolved NaOH has 3 electron pairs, which is what causes the negative charge on OH⁻. The O is able to donate one of the electron pairs to another species during a reaction. So, NaOH is a Lewis base.

0.86 moles of [tex]N_2[/tex] and 1.72 moles of Li will react.

We must place a 3 coefficient in front of Li in order to bring the equation into balance:

[tex]N_2 + 2Li = 2Li_3N[/tex]

The balanced equation demonstrates that 2 moles of Li and 1 mole of N2 react to create 2 moles of Li3N. Therefore, we can apply the following dimensional analysis to determine how many moles of Li will react with 0.86 moles of N2:

[tex]0.86 mol N_2 x (2 mol Li / 1 mol N_2) = 1.72 mol Li[/tex]

A declaration that two expressions with variables or integers are equal. In essence, equations are questions and attempts to systematically identify the solutions to these questions have been the driving forces behind the creation of mathematics.

to know more about equations here:

brainly.com/question/29657983

#SPJ1

The solution has a molarity of 0.0924 M.

The number of moles of solute per litre of solution is known as molarity.. For instance, water is both the solution and the solute when table salt is dissolved in it. Each mole of sodium chloride weighs 58.44 grammes. 58.44 grammes of sodium chloride are dissolved in one litre of water to produce one molar solution, or 1M.

Moles of solute per litre of solution is known as molarity (M).

Given: moles of NH3 = 0.355, volume of solution = 3.84 L

Molarity = 0.355 moles / 3.84 L = 0.0924 M

Therefore, the molarity of the solution is 0.0924 M.

To know more about molarity visit:-

https://brainly.com/question/8732513

#SPJ1

The first quarter is the point in the lunar cycle where the moon is one (1) week after the new moon has risen. At first quarter, the moon will also be in its "waning gibbous" phase.

The moon is called a "new moon" when it lies between the sun and the Earth, as opposed to a "full moon," which occurs when the moon is directly above. Furthermore, because we cannot even see the new moon from Earth, unlike full moons, it appears as though it doesn't exist at all.

A half (1/2) or 50% of the moon is lighted during the waning gibbous phase, which occurs once per new moon.

learn more about waning gibbous phase

https://brainly.com/question/1286359

#SPJ1

Answer:

Volume required ≈ 20.8 mL

When a solution is diluted, the total number of moles of solute (n), does not change. Only the total solution volume changes. As n=cV (molarity formula, where n = moles, c = concentration, V = volume), then the value of cV is a constant when diluting solutions. This can be expressed by the ratio:

c₁V₁ = c₂V₂, where subscripts 1 and 2 represent the concentrated and dilute solutions.

To dilute a solution of 6.0 M HCl to 0.25 M with a total volume of 0.500 L, we can use the dilution formula, where initial and final concentrations = 6.0 M and 0.25 M respectively, and final volume = 0.500 L (500 mL).

Hence, 6.0×V₁ = 0.25×0.500 = 0.125

V₁ = 0.125/6.0 = 0.02083 L

Therefore, the volume we require is ≈ 20.8 mL

Photosynthesis is the method by which plants produce their own food. Plants and other living things employ the process of photosynthesis to transform light into chemical energy that is then stored as starch that can be used at a later time. A vital step in plant growth is photosynthesis.

As autotrophs, plants produce their own sustenance. During the process of photosynthesis, they turn water, sunlight, and carbon dioxide into oxygen or simple sugars that the plant uses as fuel. These fundamental producers, which form the basis of an ecosystem, provide food for subsequent trophic levels.

Plants use the energy of a sun's light during the process of photosynthesis. Where the carbon dioxide and water are combined to create glucose, which the plants use as nourishment, using the trapped light energy to convert into chemical energy.

To know more about chemical visit:

https://brainly.com/question/29237397

#SPJ1

a. On introducing 12g of HCl, 0.047 moles of sodium chloride are produced and b. On introducing 2.1 moles of sodium dichromate, 4.2 moles of chromium (III) chloride are produced.

Number of moles = Mass of the molecule (in grams) / Molar mass of the molecule (in grams per mole)

a. To solve this problem, we need to balance the chemical equation first:

Na₂Cr₂O7 + 14HCl → 2CrCl₃ + 2NaCl + 7Cl₂ + 7H₂O

The balanced equation shows that for every 14 moles of HCl, 2 moles of NaCl are produced.

So, to find the number of moles of NaCl produced from 12g of HCl, we first need to convert grams to moles using the molar mass of HCl.

Molar mass of HCl = 1.008 + 35.453 = 36.461 g/mol

Number of moles of HCl = mass / molar mass = 12g / 36.461 g/mol = 0.329 mol

Now, we can use the mole ratio from the balanced equation to find the number of moles of NaCl produced:

2 moles NaCl / 14 moles HCl * 0.329 mol HCl = 0.047 moles NaCl

Therefore, 0.047 moles of sodium chloride are produced.

b. Using the balanced equation from part a, we can see that the mole ratio between sodium dichromate and chromium (III) chloride is 1:2.

So, if 2.1 moles of sodium dichromate are introduced, we can find the number of moles of chromium (III) chloride produced by multiplying the number of moles of sodium dichromate by the mole ratio:

2.1 moles Na₂Cr₂O₇ * 2 moles CrCl₃ / 1 mole Na₂Cr₂O₇ = 4.2 moles CrCl₃

Therefore, 4.2 moles of chromium (III) chloride are produced.

Learn more about moles here:

https://brainly.com/question/26416088

#SPJ1

The energy change for the change in state of 1.0 mol H2O (l) at 79∘C to H2O(g) at 114∘C is 42,643 J/mol.

The heat capacity of a thing is the amount of energy needed to raise its temperature by one degree Celsius. The amount of energy needed to increase the temperature of 1 gram of a substance by 1oC is known as a substance's specific heat.

We have to calculate the power needed to warm one mole of liquid water from 79∘C to 100∘C:

q1 = nCΔT

= (1.0 mol)(75.3 J/molK)(100-79 K)

= 1593 J

we have to calculate the energy,

q2 = nΔHvap

= (1.0 mol)(40.7×10^3 J/mol)

= 40,700 J

Now, we have to calculate the energy,

q3 = nCΔT

q3 = (1.0 mol)(25.0 J/molK)(114-100 K)

q3 = 350 J

The total energy change is:

ΔE = q1 + q2 + q3

ΔE = 1593 J + 40,700 J + 350 J

ΔE = 42,643 J/mol

To know more about the heat capacity visit:

https://brainly.com/question/13959344

#SPJ1

The compound NH4Cl or ammonium chloride is composed of two ions: ammonium ion (NH4+) and chloride ion (Cl-). The ammonium ion is a polyatomic cation made up of one nitrogen atom and four hydrogen atoms, while the chloride ion is a monatomic anion made up of one chlorine atom.

0.785 g of lithium hydroxide (LiOH) are produced when 0.38 g of lithium nitride (Li₃N) reacts with an excess of water.

we can see that 3 moles of lithium hydroxide (LiOH) are produced for every 1 mole of lithium nitride (Li₃N) that reacts.

To determine the mass of LiOH produced from 0.38 g of Li₃N, we need to first calculate the number of moles of Li₃N present:

molar mass of Li₃N = 3 x atomic mass of Li + 1 x atomic mass of N

= 3 x 6.94 g/mol + 1 x 14.01 g/mol

= 34.83 g/mol

moles of Li₃N = mass / molar mass

= 0.38 g / 34.83 g/mol

= 0.01093 mol

Since the balanced equation shows that 1 mole of Li₃N produces 3 moles of LiOH, we can calculate the number of moles of LiOH produced:

moles of LiOH = 3 x moles of Li₃N

= 3 x 0.01093 mol

= 0.03279 mol

Finally, we can use the molar mass of LiOH to convert from moles to grams:

molar mass of LiOH = atomic mass of Li + 1 x atomic mass of O + 1 x atomic mass of H

= 6.94 g/mol + 15.99 g/mol + 1.01 g/mol

= 23.94 g/mol

mass of LiOH produced = moles of LiOH x molar mass of LiOH

= 0.03279 mol x 23.94 g/mol

= 0.785 g

Therefore, approximately 0.785 g of lithium hydroxide (LiOH) are produced when 0.38 g of lithium nitride (Li₃N) reacts with an excess of water.

learn more about mass here

https://brainly.com/question/837939

#SPJ1

To solve molality use the following equation: ΔTb = Kb x molality.

Molality (m) is a measure of the concentration of a solution and is defined as the number of moles of solute per kilogram of solvent. To calculate molality, follow these steps:

To find the boiling point of the solution (BP solutions), the boiling point elevation constant (Kb) of the solvent and the molality of the solution. With these values, we can use the following equation:

ΔTb = Kb x molality

where ΔTb is the boiling point elevation, Kb is the boiling point elevation constant of the solvent, and molality is the molal concentration of the solution.

Find out more on STP here: https://brainly.com/question/29796637

#SPJ1

A chemist would most likely study how rain affects statues as it involves analyzing the physical and chemical changes caused by rainfall on different materials, such as metal or limestone.

A chemist would most likely study 'how rain affects statues'. This query falls under the domain of chemistry as it involves the study of physical and chemical changes caused by rainfall on different materials. Rainwater, due to the presence of various dissolved gases, can be slightly acidic. When this water comes in contact with statues, especially those made of certain metals or limestone, it can react causing corrosion or weathering, which a chemist would study.

In the case of metal statues, the acidic nature of rainwater can initiate corrosion processes, leading to the gradual degradation of the metal's surface. This phenomenon involves chemical reactions that a chemist is well-equipped to elucidate and study.

For statues crafted from limestone or other calcareous materials, rainwater can cause weathering, a process that involves chemical dissolution and physical erosion. Understanding the chemical intricacies of these reactions falls squarely within the purview of chemistry.

Hence, the study of 'how rain affects statues' inherently encompasses the investigation of the chemical alterations and transformations induced by rainfall, rendering it a quintessential domain of chemistry. This research not only sheds light on the impact of environmental factors on cultural artifacts but also contributes to the broader understanding of chemical interactions in the natural world.

https://brainly.com/question/36629312

#SPJ2

The mass of the percent of the 10 g solute in the 105 g solvent is 8.69 %.

The mass of the solute = 10 g

The mass of the solvent = 105 g

The mass of the solution = 10 g + 105 g

The mass of the solution = 115 g

The mass of the percent is expressed as :

The mass of percent = ( mass of solute / mass of solution ) × 100 %

The mass of solute = 10 g

The mass of solution = 115 g

The mass of percent = ( 10 / 115 ) × 100 %

The mass of percent = 8.69 %

Thus, the mass of percent is 8.69 % and the mass of solute is 10 and the mass of the solution is 115 g.

To learn more about mass of percent here

https://brainly.com/question/30742204

#SPJ1

Answer:

Water is a non polar molecule

Explanation:

Water interacts differently with charged and polar substances than with nonpolar substances because of the polarity of its own molecules. Water molecules are polar, with partial positive charges on the hydrogens, a partial negative charge on the oxygen, and a bent overall structure.

Explanation: The level of the liquid in a sealed jar decreases slightly due to the evaporation of some of the liquid molecules into the air space above the liquid. However, once the concentration of the liquid molecules in the air space reaches a certain level, the rate of evaporation will slow down. This is because the concentration of the liquid molecules in the air space will eventually reach a point where the rate of evaporation is balanced by the rate of condensation.

At this point, the liquid molecules in the air space will be colliding with the surface of the liquid at the same rate that liquid molecules are evaporating from the surface of the liquid. As a result, the level of the liquid will cease to change, and the liquid will remain at a stable level within the jar.