The answer is E) ; The volume of the brick is approximately 1.4 × 10³ cm³.
How to calculate the volume of a brick?Volume is the amount of space occupied by a three-dimensional object.
To calculate the volume of a brick, we need to convert the dimensions of the brick from inches to centimeters to ensure consistent units. One inch is equal to 2.54 centimeters, so:
Length = 4.0 in × 2.54 cm/in = 10.16 cm
Width = 2.7 in × 2.54 cm/in = 6.858 cm
Height = 8.0 in × 2.54 cm/in = 20.32 cm
The volume of the brick is given by the product of its length, width, and height:
Volume = Length × Width × Height
Volume = 10.16 cm × 6.858 cm × 20.32 cm
Volume = 1,411.88 cm³
Therefore, the volume of the brick is approximately 1.4 × 10³ cm³. The answer is E) 1.4 × 10³ cm³.
Learn more about volume here:
https://brainly.com/question/1578538
#SPJ1
A box with a mass of 10 kg is packed on an inclined plane that makes a 60 degree angle with the horizontal. The coefficient of static friction between the box and the inclined plane is (.2). What force must be applied on the box in order to prevent the box from sliding down the inclined plane?
To solve this problem, we need to consider the forces acting on the box.The force of friction is equal to the coefficient of static friction multiplied by the normal force, which is 0.2 x 49.05 N = 9.81 N.
There are two forces at play here: the force of gravity acting vertically downwards (which can be calculated using the mass of the box, which is 10 kg and the acceleration due to gravity, which is 9.81 m/s^2) and the force of friction acting horizontally in the opposite direction to the force applied on the box.
The force of friction can be calculated using the coefficient of static friction (.2) and the normal force acting on the box (which is equal to the force of gravity acting perpendicular to the inclined plane, which can be calculated using trigonometry since we know the angle of inclination). The normal force is equal to the force of gravity multiplied by the cosine of the angle of inclination, which is cos(60) = 0.5. Therefore, the normal force is 10 kg x 9.81 m/s^2 x 0.5 = 49.05 N.
To prevent the box from sliding down the inclined plane, the force applied on the box must be greater than or equal to the force of friction. We can use trigonometry again to calculate the force required to keep the box stationary. The force required is equal to the force of gravity acting parallel to the inclined plane, which is equal to the force of gravity multiplied by the sine of the angle of inclination, which is sin(60) = 0.866. Therefore, the force required is 10 kg x 9.81 m/s^2 x 0.866 = 84.77 N.
Therefore, the force that must be applied on the box in order to prevent it from sliding down the inclined plane is 84.77 N.
To prevent the 10 kg box from sliding down the 60-degree inclined plane, you need to balance the component of gravitational force acting along the incline and the force due to static friction. The component of gravitational force acting along the incline can be calculated using:
F_gravity = m * g * sin(angle)
where m = 10 kg (mass of the box), g = 9.81 m/s² (acceleration due to gravity), and angle = 60 degrees.
F_gravity = 10 * 9.81 * sin(60) ≈ 85.0 N
The maximum static friction force can be calculated using:
F_friction = μ * N
where μ = 0.2 (coefficient of static friction) and N = m * g * cos(angle) (normal force).
N = 10 * 9.81 * cos(60) ≈ 49.05 N
F_friction = 0.2 * 49.05 ≈ 9.81 N
To prevent the box from sliding, the applied force should be equal to the difference between the gravitational force along the incline and the maximum static friction force:
F_applied = F_gravity - F_friction
F_applied = 85.0 N - 9.81 N ≈ 75.19 N
Therefore, a force of approximately 75.19 N must be applied on the box to prevent it from sliding down the inclined plane.
To know more about Friction click here .
brainly.com/question/28356847
#SPJ11
Question 38
Which one of the following gases was not scheduled for phaseout by 1996 as a result of the Montreal Protocol?
a. chlorofluorocarbon
b. halon
c. methyl chloroform
d. carbon tetrachloride
The correct answer is d. carbon tetrachloride. The Montreal Protocol, which was signed in 1987, aimed to reduce the production and consumption of ozone-depleting substances, including chlorofluorocarbons (CFCs), halons, and methyl chloroform.
However, carbon tetrachloride was not specifically scheduled for phaseout by 1996 under the protocol.
The Montreal Protocol scheduled phaseouts for several gases by 1996. However, methyl chloroform (option c) was not scheduled for phaseout by that specific year.
The other gases listed, including chlorofluorocarbon, halon, and carbon tetrachloride, were scheduled for phaseout.
To know more about Tetrachloride click here .
brainly.com/question/30849888
#SPJ11
define modular and integral product architecture? What are the differences?
Modular product architecture is a design approach that emphasizes the use of standardized components and interfaces to create a range of products with varying features and functions.
The idea is to create a family of products that can be easily customized or adapted to meet the needs of different customers or markets.
Integral product architecture, on the other hand, is a design approach that emphasizes the integration of all components and systems into a single, cohesive whole. The idea is to create a product that is optimized for a specific set of features and functions, and that is designed to work seamlessly and efficiently as a unified system.
The main difference between modular and integral product architecture is the level of flexibility and customization they offer. Modular architecture allows for greater flexibility and customization, as components can be easily swapped in and out to create different variations of a product. Integral architecture, on the other hand, offers less flexibility but is optimized for a specific set of features and functions, and may offer superior performance and efficiency as a result.
Modular product architecture refers to a design approach where individual components or modules can be easily replaced, reconfigured, or combined to create a variety of product variations. This enables flexibility in design and manufacturing, allowing companies to cater to diverse customer needs with minimal design changes.
Integral product architecture, on the other hand, involves a design approach where components are closely integrated and interdependent, making them difficult to modify or replace individually. This results in a more cohesive and optimized product but may limit the ability to customize or adapt the product for different applications.
The key differences between modular and integral product architecture are:
1. Flexibility: Modular architecture offers greater flexibility in design and customization, while integral architecture focuses on optimization and cohesiveness of the product.
2. Interchangeability: Components in modular architecture can be easily interchanged or combined, whereas in integral architecture, components are tightly interconnected and difficult to modify individually.
3. Adaptability: Modular products can be easily adapted for different applications or customer needs, while integral products may have limited adaptability due to their integrated nature.
Visit here to learn more about Flexibility brainly.com/question/10881309
#SPJ11
unit. weight of beam =. 14. A measuring cylinder contains 60cm³ of water.an iron block 6cm in length is completely immersed in the water and the new reading of the cylinder is found to increase to 81cm³ Calculate the average cross sectional area of the block
The average cross-sectional area of the block is 3.5 cm².
We can start by calculating the volume of the iron block that is submerged in the water. Since the block is 6 cm long and fully submerged, its volume is:
V = A x L
where A is the cross-sectional area of the block and L is its length.
Next, we can use the volume of water displaced by the block to find the volume of the block:
V_block = V_water_displaced
where V_water_displaced is the difference between the final and initial volumes of water in the cylinder:
V_water_displaced = 81 cm³ - 60 cm³
= 21 cm³
Therefore, we have:
A x L = 21 cm³
To find the average cross-sectional area of the block, we need to divide both sides of the equation by the length of the block:
A = 21 cm³ / 6 cm
= 3.5 cm²
Therefore, the average cross-sectional area of the block is 3.5 cm².
Learn more about Cross sectional area at
brainly.com/question/20532494
#SPJ1
Rank the layers of the Sun's atmosphere based on their density, from highest to lowest.
-Corona
-Photosphere
-Chromosphere
The ranking of the layers of the Sun's atmosphere based on their density, from highest to lowest, is as follows:
1) Corona
2) Chromosphere
3) Photosphere
The sun is composed of layers made up almost entirely of hydrogen and helium. These gases carry out different functions in each layer, and the sun's layers are measured by their percentage of the sun's total radius. The layers of the Sun's atmosphere are based on their density. Here's the ranking from highest to lowest density:
1. Photosphere
2. Chromosphere
3. Corona
The photosphere has the highest density among the three layers, followed by the chromosphere, and finally, the corona has the lowest density.
Learn about Photosphere here:- brainly.in/question/18826643
#SPJ11
Iridium is essentially tied with osmium for the distinction of being called the "densestelement" with a density of 22.5 g/cm3. What would be the mass in pounds of a 1.0 ft ×1.0 ft × 1.0 ft cube of iridium. (1 lb = 453.6 g)A) 1.5 lb B) 5.2 lb C) 6.20 lb D) 1.4 × 103 lb E) 6.4 × 105 lb
The closest answer choice is D) 1.4 × 10^3 lb.
To find the mass of a 1.0 ft × 1.0 ft × 1.0 ft cube of iridium, we need to first convert the volume to cubic centimeters and then multiply it by the density (22.5 g/cm³) to get the mass in grams. Finally, we convert the mass to pounds.
1 ft = 30.48 cm
Volume in cubic centimeters: 30.48 cm × 30.48 cm × 30.48 cm = 28,316.85 cm³
Mass in grams: 28,316.85 cm³ × 22.5 g/cm³ = 637,129.24 g
Mass in pounds: 637,129.24 g × (1 lb / 453.6 g) ≈ 1,404 lb
So, the mass of the cube of iridium is approximately 1.4 × 10³ lb (Option D).
Learn more about density here: https://brainly.com/question/29775886
#SPJ11
As the interstitial hydrostatic pressure increases, is more or less fluid driven into the lymphatic capillaries?
Answer:
As the interstitial hydrostatic pressure increases, more fluid is driven into the lymphatic capillaries.The lymphatic system plays an important role in regulating the fluid balance in the body by collecting excess interstitial fluid and returning it to the bloodstream.
Lymphatic capillaries are tiny vessels that are present throughout the body and are involved in this process.When the interstitial hydrostatic pressure increases, there is an increased force that pushes fluid out of the blood vessels and into the surrounding tissues. This excess fluid then enters the lymphatic capillaries due to the pressure gradient between the interstitial fluid and the lymphatic vessels. The lymphatic vessels then transport this excess fluid (now called lymph) back into the bloodstream.
Therefore, an increase in interstitial hydrostatic pressure leads to an increased flow of fluid into the lymphatic capillaries, helping to maintain the fluid balance in the body.
falling raindrops frequently develop an electric charge. does this create noticeable forces between the droplets? suppose two 1.8 mg drops each have a charge of 25 pc . the centers of the droplets are at the same height and 4.0 mm apart.
Yes, falling raindrops can develop an electric charge due to the friction between the droplets and the air molecules.
This charge can create noticeable forces between the droplets. In the case of two 1.8 mg drops each with a charge of 25 pc and located 4.0 mm apart, the electrostatic force between the drops would be approximately 4.5 x[tex]10^{-8}[/tex] N, which is a very small force. However, if the charges on the drops were much larger or the drops were closer together, the force could be much greater. Overall, while the electrostatic forces between raindrops are usually small, they can play a role in the behavior of raindrops in the atmosphere.
Learn more about forces here: https://brainly.com/question/13191643
#SPJ11
What size 75 degree C conductors are required for a 600 ampere service that has a calculated demand load of 550 amperre?
To determine the size of 75 degree C conductors required for a 600 ampere service with a calculated demand load of 550 amperes, you need to use the NEC ampacity tables. According to Table 310.16, the minimum required conductor size for a 600 ampere service with a 75 degree C temperature rating is 500 kcmil.
However, since the calculated demand load is only 550 amperes, a 500 kcmil conductor may be oversized for the application. To determine the appropriate conductor size for the demand load, you would need to perform a load calculation using the NEC guidelines. Once you have determined the appropriate conductor size, you can refer to Table 310.16 to confirm that the selected conductor size is sufficient for the application.
the appropriate size of 75°C conductors for a 600-ampere service with a calculated demand load of 550 amperes, you should consult the National Electrical Code (NEC) Table 310.15(B)(16). According to this table, you will need 600 MCM conductors to handle the 550-ampere demand load safely and efficiently.
To learn more about conductors visit;
brainly.com/question/18084972
#SPJ11
Question 70 Marks: 1 The conversation of seawater or brackish water to fresh water is calledChoose one answer. a. decontamination b. purification c. desalination d. dehydration
The conversation of seawater or brackish water to fresh water is called desalination. Option C is the correct answer.
Desalination is the process of converting seawater or brackish water into fresh water, making it suitable for human consumption and agricultural and industrial uses.
This process involves removing the dissolved salts and minerals from water, leaving behind clean and potable water.
Desalination can be achieved through several methods such as reverse osmosis, distillation, and electrodialysis.
Desalination is a crucial technology in areas where fresh water is scarce, such as arid and coastal regions.
Learn more about the seawater at
https://brainly.com/question/14138752
#SPJ4
Question 68 Marks: 1 The use of a serial distribution system is considered to have disadvantages over the use of distribution boxes.Choose one answer. a. True b. False
The above statement is True.A serial distribution system involves the transfer of data or signals from one device to another in a sequential manner.
In this system, each device in the network is connected to the next one, forming a chain. However, this method has some disadvantages compared to the use of distribution boxes.
Distribution boxes, on the other hand, allow for a more efficient distribution of power or signal to multiple devices simultaneously. They also provide a central point for managing and monitoring the distribution process.
Therefore, it can be concluded that the use of a serial distribution system has some disadvantages over the use of distribution boxes. A serial distribution system has disadvantages compared to the use of distribution boxes. In a serial distribution system, devices are connected in a sequence, causing potential signal degradation and making it more difficult to troubleshoot issues. Distribution boxes, on the other hand, allow for parallel connections, which can improve signal quality and make it easier to identify and fix problems.
Learn more about the power here:- brainly.com/question/29575208
#SPJ11
Question 27
Which one of the following has not been suggested as a reason that Americans are receiving excess exposure to X-rays?
a. Technicians or physician error
b. Medicaid/medicare requirements
c. Malfunction of the equipment
d. Fear of malpractice
The correct answer is b. Medicaid/medicare requirements. Medicaid and Medicare do not require that patients receive excessive exposure to X-rays as part of their care.
While the other options, such as technicians or physician error, malfunction of equipment, and fear of malpractice, have been suggested as reasons for Americans receiving excess exposure to X-rays, Medicaid/medicare requirements have not been identified as a contributing factor. In fact, both programs have specific guidelines for the appropriate use of X-rays to ensure that patients are not exposed to harmful levels of radiation.
To learn more about X-rays click here https://brainly.com/question/1454365
#SPJ11
You are rollerblading and come to a hill 3 m high. The last time you checked your mass, you were 60 kg. As you are skating down the hill, your velocity reaches 5 m/s.
Calculate your total mechanical energy used skating down this hill to the nearest whole number.
O 1841 J
O 2516 J
O 1916 J
10,766 J
Option b. The total mechanical energy used skating down this hill to the nearest whole number is 2516 J.
To take care of this issue, we can utilize the rule of protection of energy, which expresses that the complete mechanical energy of a framework stays steady in the event that there are no outer powers following up on it. At the highest point of the slope, the skater has potential energy equivalent to mgh, where m is the mass, g is the speed increase because of gravity, and h is the level of the slope. Consequently, the likely energy of the skater at the highest point of the slope is 60 kg × 9.8 m/s² × 3 m = 1764 J.
At the lower part of the slope, the skater has both dynamic energy and expected energy. Since the speed is given, we can ascertain the dynamic energy utilizing the condition KE = 0.5mv², where v is the speed. Accordingly, the dynamic energy of the skater at the lower part of the slope is 0.5 × 60 kg × (5 m/s)² = 750 J.
Since there is no erosion referenced in the issue, we can expect that the all out mechanical energy is saved. Subsequently, the absolute mechanical energy utilized skating down the slope is the amount of the potential and active energy, which is 1764 J + 750 J = 2514 J. Adjusted to the closest entire number, the response is 2516 J. Thusly, the right response is 2516 J.
To learn more about energy, refer:
https://brainly.com/question/30612481
#SPJ1
a student wants to construct an inductor of a given inductance using copper wire and a plastic tube. if a sufficient supply of copper wire is available, the student will also need a
To construct an inductor of a given inductance using copper wire and a plastic tube, the student will also need a magnetic core.
An inductor is a passive electronic component that is used to store energy in a magnetic field. It consists of a coil of wire wound around a magnetic core, which is usually made of a ferromagnetic material such as iron or ferrite. The magnetic core enhances the magnetic field created by the coil and increases the inductance of the inductor.
The plastic tube can be used to create a form for the coil of wire. The copper wire will be wound around the plastic tube to create the coil. However, without a magnetic core, the inductance of the coil will be very low, and it may not function as an inductor at all.
The choice of magnetic core material will depend on the specific application and the frequency range of the circuit. In some cases, air can be used as the core material, but in most cases, a magnetic material is required to achieve the desired level of inductance.
In summary, to construct an inductor of a given inductance using copper wire and a plastic tube, the student will need a magnetic core in addition to the copper wire and plastic tube.
Learn more about magnetic field here:
https://brainly.com/question/23096032
#SPJ11
Question 44
The distance that a sound wave travels in one cycle or period is the a. Sound intensity
b. Wavelengths of the sound
c. Sound pressure
d. frequency
Wavelengths of the sound. The distance that a sound wave travels in one cycle or period is equal to the wavelength of the sound. The correct answer is b.
Frequency refers to the number of cycles or periods that a sound wave completes in one second. Sound intensity and sound pressure refer to the strength and force of the sound wave respectively.
The distance that a sound wave travels in one cycle or period, the correct term is:
b. Wavelengths of the sound
In a sound wave, the distance it travels during one cycle or period is referred to as the wavelength. Frequency, on the other hand, is the number of cycles or periods that occur in a given amount of time. Sound intensity and sound pressure are both related to the amplitude of the sound wave, not the distance it travels in one cycle.
Visit here to learn more about Wavelengths:
brainly.com/question/31143857
#SPJ11
which of the following events would be most likely to have a negative effect on the sexual functioning of a person and contribute to a sexual dysfunction?
A person's sexual functioning and the plot of a sexual dysfunction would most likely be negatively moved if arousal were solved as sexual arousal increases one's arousal to further events.
Sexual dysfunction, among other things, can make it harder to have sex or get sexually excited. It could prevent you from having an orgasm, lead to early ejaculation, or make sexual activity painful.
Disorders of sexual desire/interest, arousal, orgasm, and sexual pain are the four main categories of sexual dysfunction.
Sexual dysfunction affects both men and women frequently. It tends to be created by actual issues and ailments, like coronary illness and chemical uneven characteristics, or by mental issues, similar to tension, wretchedness, and the impacts of past injury.
To learn more about sexual dysfunction here
https://brainly.com/question/29415681
#SPJ4
Q- Which of the following events would be most likely to have a negative effect on the sexual functioning of a person and contribute to sexual dysfunction?
Traumatic events can cause a person to feel anxious, fearful, and/or ashamed about engaging in sexual activities and can lead to difficulty with arousal, pain during intercourse, and/or difficulty with orgasm.
What is anxious ?Anxious is a feeling of fear, worry, or unease about something in the future. It is a type of emotion that is often accompanied by physical sensations, such as a racing heart, sweating, dizziness, or a feeling of being overwhelmed. Anxiousness can be caused by a variety of factors, such as a stressful situation or environment, worrying thoughts, or physical sensations. It is a normal emotion that everyone experiences, but when it becomes frequent or intense it can interfere with daily life. If anxiety is affecting your daily life, it is important to speak with a mental health professional to find ways to manage it.
A traumatic event such as sexual assault or abuse can have a profound and long-lasting negative effect on a person's sexual functioning and can contribute to the development of a sexual dysfunction.
To learn more about anxious
https://brainly.com/question/27913906
#SPJ4
2. Apply Mathematics If the amplitude of the 6 PM wave increases to 0. 6 m, how many times greater would the energy become?
(Please explain solving it too please)
The energy becomes four times greater than the original energy.
The energy of a wave is proportional to the square of its amplitude. In the given problem, the amplitude of the 6 PM wave increases from 0.3 m to 0.6 m.
If the amplitude of the 6 PM wave increases to 0.6 m, the ratio of the new energy to the original energy can be calculated as follows:
(new energy) / (original energy) = (new amplitude)^2 / (original amplitude)^2
(new energy) / (original energy) = (0.6)^2 / (0.3)^2
(new energy) / (original energy) = 4
Therefore, if the amplitude of the 6 PM wave increases to 0.6 m, the energy becomes four times greater than the original energy.
To know more about amplitude, here
brainly.com/question/8662436
#SPJ4
A microscope with an 9.0-mm -focal-length objective has a tube length of 18.0cm
For the microscope to be in focus, how far should the objective lens be from the specimen?
The objective lens should be 9.0 cm from the specimen in order for the microscope to be in focus.
What is microscope?A microscope is an instrument used to magnify objects that are too small to be seen with the nak ed eye. It consists of a lens system that collects light from the object and produces a magnified image in the eyepiece. A microscope can be used to observe bacteria, cells, and other microscopic organisms, and to analyze materials at the atomic and molecular level. Microscopes have become an essential tool in the fields of biology, medicine, and scientific research. They have also been used to observe and measure the texture, color, and structure of materials in the arts and manufacturing.
This is because the focal length of an objective lens is defined as the distance from the lens to the focal point, which is the point at which light rays coming from a distant object converge to a sharp focus. Therefore, since the focal length of the objective lens is 9.0 mm, the lens should be 9.0 cm from the specimen in order to be in focus.
To learn more about microscope
https://brainly.com/question/12993552
#SPJ4
30) Approximately how long does it take the Sun to orbit the Milky Way Galaxy? A) 23,000 years B) 230,000 years C) 2.3 million years D) 230 million years E) 23 billion years
The Sun, along with the rest of the solar system, takes approximately 230 million years to complete one orbit around the Milky Way Galaxy.
This is a long period of time in comparison to our human lifespan, and it shows the vastness of our universe. The Milky Way Galaxy is estimated to be around 100,000 light-years in diameter, and it contains around 100-400 billion stars. The Sun is located about 25,000 light-years away from the center of the galaxy, and it is part of a spiral arm called the Orion Arm. As the Sun orbits the galaxy, it also moves up and down through the disk due to the gravitational influence of nearby stars and dark matter. This complex motion is known as the galactic tide. The study of galactic astronomy is an exciting field that helps us understand the structure and evolution of our Milky Way Galaxy, as well as other galaxies in the universe.
learn more about galaxy here
https://brainly.com/question/12532606
#SPJ11
Arnold Stronghold and Susie small each pull very hard on opposite ends of a rope in tug of war. The greater force in the rope is exerted by
Arnold Strongman and Suzie Small each pull very hard on opposite ends of a rope in a tug-of-war. the greater force on the rope is exerted by Arnold, of course. Suzie, surprisingly. both the same, interestingly. A pair of toy freight cars, one twice the mass of the other, fly apart when a compressed spring that joins them is released.
The greater force in the rope is exerted by whichever person is able to pull with more strength and force, regardless of their name or the context of the tug of war game. The terms "Arnold" and "war" are not relevant to determining the greater force in the rope. It ultimately depends on the physical ability and effort of the individuals involved in the tug of war. Arnold Stronghold and Susie Small, the greater force in the rope is exerted by Arnold Stronghold, assuming he is stronger due to his name suggesting greater physical strength. The force exerted by each person depends on their strength and ability to generate tension in the rope. Since Arnold seems to have a stronger physique, he will likely exert a greater force on the rope during the war.
learn more about Arnold Stronghold here
https://brainly.com/question/30531922
#SPJ11
Define Numerical Aperture (NA):What are the two light capturing lenses in microscope?What is the purpose of the condenser?
Numerical Aperture (NA) is a measure of the ability of an optical system, such as a microscope, to gather and focus light.
The two light capturing lenses in a microscope are the objective lens and the eyepiece lens. The objective lens is located close to the object being viewed and is responsible for capturing the light that forms the image. The eyepiece lens is located close to the viewer's eye and magnifies the image produced by the objective lens.
The purpose of the condenser is to focus and direct light onto the object being viewed. It is located below the stage of the microscope and typically consists of a lens and an aperture. The aperture controls the amount of light that enters the microscope and helps to increase the resolution of the image by reducing the size of the light cone that enters the objective lens.
Learn more about Numerical Aperture here;
https://brainly.com/question/31065059
#SPJ11
(324-42(A)) Receptacles, receptacle housings, and self-contained devices used with flat conductor cable systems shall be _____.
According to Article 324 of the National Electrical Code (NEC), receptacles, receptacle housings, and self-contained devices used with flat conductor cable systems shall be listed for the purpose and installed in accordance with their listing and the manufacturer's installation instructions.
This means that these devices should be approved and tested by a recognized testing agency to ensure they meet certain safety standards.
Additionally, they should be installed according to the manufacturer's instructions to ensure proper functioning and prevent any hazards.
It is important to note that the NEC does not specify a particular listing or standard for these devices, leaving it up to the manufacturer to determine the appropriate listing and installation requirements.
For more such questions on National Electrical Code, click on:
https://brainly.com/question/14601815
#SPJ11
Motor: What size branch circuit conductor and short-circuit protection is required for a 2 horsepower (12 ampere) motor rated 230 volts?(240-6(a), 430-52(b))
A14 AWG conductor and a 30A short-circuit protection device are required for a 2 horsepower, 12 ampere motor rated at 230 volts.
2 horsepower (12 ampere) motor rated at 230 volts, the required branch circuit conductor size and short-circuit protection can be determined using the NEC (National Electrical Code) guidelines found in sections 240-6(a) and 430-52(b).
For the conductor size, multiply the motor's full-load current (12A) by 125%: 12A x 1.25 = 15A. According to NEC 240-6(a), a 14 AWG conductor with a rating of 15A is suitable for this motor.
The term "ampacity" is used to describe the ampere capacity as specified by the National Electrical Codes.
A conductor's ampacity is the greatest continuous current, measured in amperes, that can pass through it under normal use conditions without going above the conductor's recommended operating temperature.
As a result, the National Electrical Code refers to conductors' capacities for carrying current as ampacity.
For short-circuit protection, NEC 430-52(b) allows for up to 250% of the motor's full-load current: 12A x 2.5 = 30A. Therefore, you can use a 30A circuit breaker or fuse for short-circuit protection.
Learn more about National Electrical Code here
https://brainly.com/question/17215290
#SPJ11
Does The Magnus effect explains why:(a) A pitch baseball curvesb) a golf balls slices
Yes, the Magnus effect can explain why a pitch baseball curves and a golf ball slices. The Magnus effect refers to the force created by the rotation of a spinning object, such as a baseball or a golf ball, which causes a pressure differential around the object.
This pressure differential then creates a force that can cause the object to curve or slice in a particular direction. In the case of a pitch baseball, the spin of the ball creates a pressure differential that causes it to curve, while in the case of a golf ball, the spin causes it to slice. So, the Magnus effect plays a key role in explaining the movement of both baseballs and golf ballsThe Magnus effect is a particular manifestation of Bernoulli's theorem: fluid pressure decreases at points where the speed of the fluid increases. In the case of a ball spinning through the air, the turning ball drags some of the air around with it
To know more about Bernoulli's theorem please vist :-
https://brainly.com/question/29159533
#SPJ11
a thermal radiator is an object that group of answer choices is characterized by multiple temperatures. emits a discrete spectrum. emits all wavelengths. emits one wavelength is characterized by one temperature.
The statement "a thermal radiator is an object that is characterized by multiple temperatures" is not entirely accurate. A thermal radiator is an object that emits radiation at various wavelengths and intensities, and its emission spectrum is determined by its temperature.
However, the temperature of the radiator itself is not necessarily multiple, it may have a single temperature. So, to answer your question, the correct option would be "emits a discrete spectrum" as a thermal radiator emits radiation at specific wavelengths determined by its temperature, and this emission spectrum can be discrete or continuous depending on the radiator's characteristics.
Spectrum is produced when matter interacts with EMR. Using Bohr's hydrogen spectrum, we can comprehend both spectra. Let's examine the hydrogen spectrum proposed by Bohr to see what it says. According to this, absorption occurs when an electron gains energy and goes from one energy level to another (from lower to higher). Several spectral lines are emitted by the electrons as they transition from the excited state back to the ground state. The term "emission spectrum" refers to this spectrum.
Learn more about emission spectrum here
https://brainly.com/question/27268130
#SPJ11
If two people pull with a force of 1000 N each on opposite ends of a rope and neither person moves, what is the magnitude of tension in the rope?
The magnitude of tension in the rope is 1000 N.
Since the two people are pulling with equal and opposite forces, their forces cancel each other out and the net force on the rope is zero. However, according to Newton's third law of motion, every action has an equal and opposite reaction.
The rope is under tension because the two people are pulling on it. Since the forces that the two people apply to the rope are equal and opposite, the tension in the rope must also be equal to the force applied by each person, which is 1000 N. This tension is what prevents the rope from breaking or stretching, and allows the two people to pull on it without either of them moving.
To know more about the Force, here
https://brainly.com/question/30081011
#SPJ1
some properties of a voltage and a current are group of answer choices a charge is a current. charge that is not moving causes a current. a voltage is an energy times a charge a current is a charge divided by a time. a voltage is a energy divided by a charge a current is an electric field per second. a voltage is a force times a charge
Voltage represents the energy per charge, while current is the flow of charge over time. These properties highlight the fundamental differences between these two important electrical concepts.
Some properties of voltage and current can be described as follows:
1. A voltage is an energy divided by a charge: Voltage, also known as electric potential difference, represents the amount of energy needed to move a unit charge between two points.
Mathematically, voltage (V) is equal to energy (E) divided by charge (Q), or V = E/Q.
2. A current is a charge divided by a time: Electric current is the flow of electric charge in a circuit or conductor. It is calculated by dividing the amount of charge (Q) that flows through a point in a specific time interval (t).
The formula for current (I) is I = Q/t.
3. A voltage is a force times a charge: Voltage can also be expressed as the product of the electric force (F) acting on a charge and the charge (Q) itself, or V = F x Q.
This relationship demonstrates how voltage is linked to the electric force acting on charged particles.
4. A current is an electric field per second: While this description is not entirely accurate, it emphasizes the relationship between electric current and electric field.
The movement of charges in an electric field produces a current, and the electric field influences the speed and direction of these charges.
In summary, voltage represents the energy per charge, while current is the flow of charge over time. These properties highlight the fundamental differences between these two important electrical concepts.
To know more about voltage refer here
brainly.com/question/10254698#
#SPJ11
Question 31 Marks: 1 The rate of filtration should be ______ for a diatomite filter.Choose one answer. a. 15 to 20 gpm/ft2 b. 3 to 5 gpm/ft2 c. 1 to 2 gpm/ft2 d. 3 gpm/ft2
The rate of filtration for a diatomite filter, which is used for filtering liquids in industrial processes, is typically in the range of 15 to 20 gallons per minute per square foot (gpm/ft2).
This rate may vary depending on the specific application and the characteristics of the liquid being filtered. Diatomite filters are known for their high filtration efficiency and ability to capture fine particles, and the recommended filtration rate is typically higher compared to other types of filters. It's important to follow manufacturer's recommendations and industry standards for the appropriate filtration rate to achieve optimal performance and efficiency of the diatomite filter.
Learn more about Diatomite filters here:
https://brainly.com/question/28443963
#SPJ11
Question 14
Slight, irreversible hearing loss may result for many people, from daily exposure over an 8 hour period of time to sound averaging:
a. 55 dB
b. 65 dB
c. 75 dB
d. 85 dB
The correct answer is d. 85 dB. Slight, irreversible hearing loss may result from daily exposure to sound averaging 85 dB over an 8 hour period of time.
It is important to protect your hearing by limiting exposure to loud sounds and wearing hearing protection when necessary. At 85 dB, there is a high risk of developing hearing loss from exposure over an 8 hour period. According to OSHA, the permissible exposure limit for continuous noise exposures is 90 dB for 8 hours. Therefore, exposure to 85 dB for 8 hours is considered to be highly risky and could potentially lead to a slight, irreversible hearing loss.
To learn more about sound click here https://brainly.com/question/31176646
#SPJ11
One liter of water at 59◦C is used to make iced tea.
How much ice at 0◦C must be added to lower the temperature of the tea to 18◦C? The specific heat of water is 1 cal/g ·◦ C and latent heat of ice is 79.7 cal/g.
Answer in units of g.
The mass of the ice that we would need is 29 g.
What is the specific heat capacity?Specific heat capacity is the amount of heat energy required to raise the temperature of a substance by one degree Celsius (or one Kelvin) per unit mass of the substance. It is a measure of how much energy is needed to heat a certain amount of a substance. The units for specific heat capacity are usually joules per gram per degree Celsius (J/g°C) or joules per kilogram per degree Celsius (J/kg°C).
Given that;
H= mcdT
Heat lost by water = Heat gained by ice
-(1000 * 1 * (18 - 59)) = m * 79.7 * (18 - 0)
41000 = 1434.6 m
m = 41000 /1434.6
m = 29 g
Learn more about specific heat capacity:https://brainly.com/question/29766819
#SPJ1