what physical quantity that can be measured relates directly to inertia?

When preparing a wet mount specimen for viewing, it should be covered with a coverslip.

A coverslip is a thin, flat piece of glass or plastic that is placed over the specimen on the slide. It is used to protect the specimen from being compressed or damaged, and to prevent evaporation of the liquid medium that the specimen is suspended in. The coverslip also helps to keep the specimen in focus and allows the viewer to observe the specimen clearly under a microscope.

To prepare a wet mount, a small amount of the specimen is placed on a microscope slide and a drop of liquid medium (such as water, saline, or stain) is added. The coverslip is then placed over the specimen at a slight angle and carefully lowered onto the slide to avoid trapping air bubbles. The coverslip should be pressed down gently to flatten the specimen and remove any excess liquid, but not so hard as to crush the specimen.

To learn more about Coverslip :

https://brainly.com/question/28530290

#SPJ4

Answer:

Below

Explanation:

You have total current correct   3 A    from the ammeter in the circuit.

Must find total resistance to calculate the Vt

  the two resistors in parallel =   12 * 6 / (12+6) = 4 Ω

     then add this equivalent R to the other R that is in series  

              8 + 4 = 12 Ω      < ====   Rt

then   Vt = It Rt

          Vt = 3 * 12 = 36 v

V1 = It R1 = 3 * 8 = 24 V

V2 and V3 are equal and would be the voltage left 36-24 = 12 v

     or you could calculate V2 and V3        V2 = V3 = It R = 3 ( 4 Ω) = 12 v

Answer:

The dragster's velocity in mi/h when it crosses the finish line is 159.2 mi/h. This can be calculated by taking the distance traveled divided by the time taken, multiplied by 3600 (for conversion of seconds to hours).

The firemen should adjust the angle of elevation of the hose to 41.1 degrees in order to hit the building 45.0 m away in 3.00 s.

We can use the equations of motion to solve this problem. We know that the initial velocity of the water stream is 25.0 m/s and that it moves in projectile motion. We need to find the angle of elevation α that will allow the water to reach a building 45.0 m away in 3.00 s.

Let's define the x-axis to be horizontal and the y-axis to be vertical. The initial velocity of the water stream can be broken down into its x and y components:

vx = v cosα = 25.0 cosα

vy = v sinα = 25.0 sinα

where v is the magnitude of the initial velocity.

Using the equation of motion for the x-direction, we can find the time it takes for the water to reach the building:

x = vx t

45.0 = 25.0 cosα t

t = 45.0 / (25.0 cosα)

Using the equation of motion for the y-direction, we can find the angle of elevation:

y = vy t - 1/2 g t^2

0 = 25.0 sinα (45.0 / (25.0 cosα)) - 1/2 (9.81) (45.0 / (25.0 cosα))^2

0 = 45.0 tanα - 1/2 (9.81) (45.0 / 25.0)^2

tanα = (1/2) (9.81) (45.0 / 25.0)^2 / 45.0

α = tan^-1((1/2) (9.81) (45.0 / 25.0)^2 / 45.0) = 41.1 degrees

To know more about angle of elevation here

https://brainly.com/question/30133103

#SPJ4

The period of a pendulum is the time it takes for one complete back-and-forth swing or oscillation of the pendulum. It is the time interval between two successive swings of the pendulum.

The period of a simple pendulum can be calculated using the following formula:

T = 2π√(L/g)

where T is the period of the pendulum in seconds, L is the length of the pendulum in meters, and g is the acceleration due to gravity in meters per second squared.

This formula assumes that the pendulum is a simple, idealized pendulum consisting of a massless rod and a point mass (the "bob") at the end. It also assumes that the pendulum swings in a small angle (less than about 15 degrees) and that there is no air resistance or friction.

To know more about oscillation here

https://brainly.com/question/12622728

#SPJ4

Answer:

pushes is the correct answer

14.14 (resultant vector)

The Magnitude is 17.20 m and Direction is 270° south of east

Calculation

1. Calculate the net displacement:

12.7 m northward - 4.50 m westward = 8.20 m northward

2. Calculate the magnitude of the third displacement:

Net displacement magnitude = 8.20 m

Third displacement magnitude = 8.20 m

3. Calculate the direction of the third displacement:

Net displacement direction = 90° north of east

Third displacement direction = 270° south of east

What is distance?

Distance is the length of the path between two points. It is measured in metric units such as meters, kilometers, or miles.

What is displacement?

Displacement is the difference between the initial and final positions of a particle. It is a vector quantity and is measured in the same units as distance (meters, kilometers, or miles).

The magnitude of the child's third displacement is 17.20 m and the direction is 270° south of east.

Learn more about distance and displacement from given link:

https://brainly.com/question/29769926

#SPJ1

Answer:

0.11m

Explanation:

The speed of sound at 21°C is approximately 343 m/s.

To calculate the wavelength for a frequency of 3 kHz, we can use the formula:

wavelength = speed of sound / frequency

Plugging in the values we have:

wavelength = 343 m/s / 3000 Hz = 0.1143 meters

Rounding to two decimal places, we get a wavelength of 0.11 meters or 0.11 m.

Answer:

The farther it is from the Sun, the weaker the Sun's gravitational pull, and the slower it moves in its orbit.

The microscopic structure of a polarizing filter is analogous to a kitchen sieve. Hence, the correct option is (C).

The microscopic structure of a polarizing filter is analogous to a kitchen sieve. A polarizing filter is made up of a series of parallel lines or fibers that allow light to pass through in only one direction, while blocking light that oscillates in other directions. This is similar to a kitchen sieve, which has a series of parallel holes that allow small particles to pass through in one direction while blocking particles that try to pass through in other directions. A window screen, barbeque grill, and plate of spaghetti all have a similar function of filtering particles, but they do not have the same parallel structure as a polarizing filter or kitchen sieve. A roll of coins also has a parallel structure, but it does not filter light or particles in the same way as a polarizing filter or kitchen sieve. Therefore, the best analogy for the microscopic structure of a polarizing filter is a kitchen sieve.

To know more about polarizing filter please refer: https://brainly.com/question/13826447

#SPJ4

Answer:

speed of the boat = 10.67 m/s...

direction the boat is 38.2 degrees north of east...

Explanation:

To solve this problem, we can use vector addition.

Let the velocity of the boat be represented by vector B, which has a magnitude of 12 m/s and is directed 45 degrees north of east. We can represent this vector as:

B = 12 m/s at 45 degrees

Let the velocity of the ocean current be represented by vector C, which has a magnitude of 2 m/s and is directed directly south. We can represent this vector as:

C = 2 m/s at 270 degrees

To find the actual speed of the boat and the direction it is heading, we need to add these two vectors together using vector addition. To do this, we can break each vector into its x and y components:

Bx = 12 m/s * cos(45) = 8.49 m/s

By = 12 m/s * sin(45) = 8.49 m/s

Cx = 0 m/s

Cy = -2 m/s

Now, we can add the x and y components of the vectors separately:

Rx = Bx + Cx = 8.49 m/s + 0 m/s = 8.49 m/s

Ry = By + Cy = 8.49 m/s - 2 m/s = 6.49 m/s

The resulting vector R has a magnitude of:

|R| = sqrt(Rx^2 + Ry^2) = sqrt((8.49 m/s)^2 + (6.49 m/s)^2) = 10.67 m/s

And a direction of:

theta = arctan(Ry/Rx) = arctan(6.49 m/s/8.49 m/s) = 38.2 degrees

Therefore, the actual speed of the boat is 10.67 m/s and the direction the boat is heading is 38.2 degrees north of east...

If Alex wishes to rotate his skateboard, he must apply a torque.

Torque is the twisting or rotational force that is required to cause an object to rotate around an axis or pivot point. In the case of a skateboard, if Alex wants to rotate the board, he needs to apply a torque by pushing on one end of the board while keeping the other end stationary or pushing in the opposite direction. This will cause the board to rotate around its center of mass.

A rotational maneuver is a general term that could refer to any type of rotational movement or action, whereas a pause before bearing down on the board is not directly related to the act of rotating the skateboard.

Therefore, option A) torque is correct option. If Alex wishes to rotate his skateboard, he must apply a torque

for such more question on rotation

https://brainly.com/question/25803184

#SPJ4

The requried solutions,
(a) weight of book
(b) Normal force of 5 N, by the table
(f) Yes, the downward force in part a and the upward force in part b constitute a 3rd law pair

Newton's 3rd law of motion, also known as the law of action and reaction, states that "For every action, there is an equal and opposite reaction." This means that when an object exerts a force on another object, the second object exerts an equal and opposite force back on the first object.

Here,
As mentioned in the question, A book weighing 5 N rests on top of a table So,
Part A,
A downward force of magnitude 5 N is exerted on the book by the force of its own weight.

Part B
An upward force of magnitude 5 N is exerted on the book by the table.

So, Newton's laws 3rd law could have been used to predict that the forces in Parts A and B are equal and opposite.

Learn more about newtons laws of motion here:
https://brainly.com/question/14967902
#SPJ1

The repelling thrust between the two plastic spheres is [tex]2.83x10^-13 N[/tex].

The force of repulsion between two plastic spheres can be calculated using Coulomb's Law, which states that the force between two charged particles is directly proportional to the product of their charges and inversely proportional to the square of the distance between them.

The formula for Coulomb's Law is:

Where F is the force of repulsion, k is Coulomb's constant [tex](9x10^9 Nm^2/C^2)[/tex], q¹ and q² are the charges on the plastic spheres, and r is the distance between them.

Given that each sphere has a deficit of [tex]1.2x10^8[/tex] electrons, we can calculate the charge on each sphere using the formula q = n*e, where n is the number of electrons and e is the charge of an electron [tex](1.6x10^-19 C)[/tex].

[tex]q¹ = q² = (1.2x10^8)*(1.6x10^-19) = 1.92x10^-11 C[/tex]

Plugging in the values into the formula for Coulomb's Law, we get:

[tex]F = (9x10^9)*(1.92x10^-11)*(1.92x10^-11)/(1.1)^2F = 2.83x10^-13 N[/tex]

Therefore, the force of repulsion between the two plastic spheres is [tex]2.83x10^-13 N[/tex].

Learn more about Coulomb's Law at: https://brainly.com/question/26892767

#SPJ11

It will be very difficult to if you could travel back to the time when the Earth first formed as a planet. It has lots of volcano with no water or ocean.

Earth would have been a very hostile and unpleasant planet when it originally formed, and life would not have been viable. Without any water or ocean, it was merely molten volcanic soil. At that time, the atmosphere and life were not even established. First, there was a time when the Earth's atmosphere was highly hot and there were frequent collisions with celestial bodies. Hence, the heat generated in the atmosphere was in a molten volcanic state. lava and magma alone. Ocean formation and, by extension, life, were prohibited by high temperatures.

Learn more about earth here:

https://brainly.com/question/28465561

#SPJ4

The answer that best describes the surface of the Earth at this time is option B, "Earth has lots of volcanoes."

If you could travel back in time to when the Earth first formed as a planet, the surface of the Earth would likely be characterized by frequent volcanic activity and a lack of water. Therefore, the answer that best describes the surface of the Earth at this time is option B, "Earth has lots of volcanoes."

During the early stages of the Earth's formation, intense heat and pressure caused the surface to be covered in molten lava and ash. Over time, this activity led to the formation of the Earth's crust, and the continued volcanic activity helped shape the planet's surface and atmosphere.

It wasn't until later, through a process known as outgassing, that water vapor and other gases were released from the Earth's interior and began to accumulate in the atmosphere, eventually leading to the formation of oceans and the emergence of life.

Learn more about atmosphere:

https://brainly.com/question/28310375

#SPJ4

Answer:

B

Explanation:

Because spring waves are transverse waves and they move perpendicularly to the direction of motion

Mass fluid flow through and through capillary beds necessitates transport mechanism that is significantly more effective than simple diffusion.

The correct answer is False

a huge quantity, quantity, or number is a feature of a body that determines its inertia and is frequently used to gauge the quantity of substance it contains and what makes it have weight inside a gravitational field. mass of stuff.

Using a balance would be necessary to determine mass. A triple beam scale or an analytical balance can be used to measure mass in a laboratory, but the traditional balance shown below might help you understand what mass is.

To know more about mass visit:

https://brainly.com/question/18064917

#SPJ4

The minimum length of the curve for the required sight distance is 338.12 feet.

Locate the station point of the highest point on the curve.

(dy)/(dx) = 0

(dy)/(dx) = - 0.19 × 2x + 1.2 = 0

x = 3.1579stations

The elevation of the very best point at the curve is

y = - 0.19 × 3.1579² + 1.2 × 3.1579 + 1094.8

= 1096.69ft

Deceleration rate a is 11.2ft / (s² ). Reaction time t is 2.5seconds

The necessary SSD for the design speed of 60mph is

V 1 ^ 2/ 2g(( a / g ) pm G) +V 1 × t

,= (60 * 5280ft)² /(60 × 60s)) ² /(2 × 32.2((112/322))) + ((60 * 5280f)/(60 * 60s)) * 2.5

= 565.71pi

Lm= (|G1 - G2| × SSD² )/2158  = (|1.2 + 1.08| × 565.71²) /2158

= 338.12ft

speed in physics is a scalar amount that refers back to the fee at which an item moves, typically expressed in units of meters in line with seconds (m/s) or kilometers in step with the hour (km/h). it is defined as the distance an item travels in line with a unit of time, which means that it only takes into consideration the value of the item's motion and not its path.

Immediate speed refers to the speed of an item at any given second, at the same time as average speed is calculated over a period of time. the velocity of an object may be inspired by means of several elements, which include the forces appearing upon it and the medium through which it is transferring.

Further to hurry, there are different associated standards in physics, along with speed, which incorporates each the rate and course of an item's movement and acceleration, which describes the rate at which an object's velocity changes over the years.

To learn more about Speed visit here:

brainly.com/question/28224010

#SPJ4

The conversion from meters per second (m/s) to Mach is dependent on the speed of sound, which varies with temperature and altitude.

Mach is a unit of speed that is based on the speed of sound in a given medium, usually air. It is defined as the ratio of the speed of an object to the speed of sound in the same medium. The speed of sound, in turn, is affected by temperature and altitude, since the density and compressibility of the medium change with these factors.

Therefore, the conversion factor between m/s and Mach is not a fixed value, but rather depends on the specific conditions of the medium in which the object is traveling. A common approximation for the speed of sound at sea level and 15 degrees Celsius is 340 m/s, which corresponds to Mach 1.

To know more about the Mach, here

brainly.com/question/1178111

#SPJ4

When two identical parallel plate capacitors are given the same charge Q, after which they are disconnected from the battery. after C2 has been charged and disconnected, it is filled with a dielectric. Comparing the voltages of two capacitors will result to

The voltage V of a capacitor is given by the formula

V = Q/C,

where

Q is the charge on the capacitor and

C is the capacitance of the capacitor.

Since the two capacitors are identical and have the same charge Q, their voltages V1 and V2 before disconnection from the battery would be equal

V1 = V2.

After C2 has been charged and disconnected, and a dielectric is inserted, the capacitance of C2 increases, which in turn reduces the voltage across it. This is because the charge on the capacitor remains the same, but the capacitance increases, leading to a decrease in the voltage.

Therefore, the voltage V2 across C2 decreases, and the voltage V1 across C1 remains the same. Hence, the correct option is (a) V1 > V2.

Learn more about capacitor at:

https://brainly.com/question/27393410

#SPJ1

The loop rule (also known as Kirchhoff's voltage law) states that the sum of the potential differences around a closed loop in a circuit must be zero.

Electric current is the flow of electric charge through a material. It is typically expressed in units of amperes (A), which represent the rate at which charge flows through a conductor.

Here,
In general, the loop rule (also known as Kirchhoff's voltage law) states that the sum of the potential differences around a closed loop in a circuit must be zero. This can be expressed mathematically as

ΣV = 0

where ΣV is the sum of the potential differences (voltages) around the loop. The potential differences can be calculated using Ohm's law (V = IR) and the properties of circuit elements such as resistors, capacitors, and inductors.

Learn more about electric current here;

https://brainly.com/question/2264542

#SPJ1

The conversion of 17 degrees The conversion of 17 degrees Celsius to Fahrenheit is 62.6 degrees Fahrenheit.

The equation F = 9/5C + 32 relates temperature measured in degrees Celsius (C) to degrees Fahrenheit (F). The formula is used to convert temperatures from Celsius to Fahrenheit , and vice versa. To use the formula, you simply plug in the known temperature in Celsius (or Fahrenheit), and then solve for the unknown temperature in Fahrenheit (or Celsius).

To convert Celsius to Fahrenheit, you would use the formula F = 9/5C + 32, where C is the temperature in Celsius and F is the temperature in Fahrenheit. Thus, for 17 degrees Celsius, the formula would be F = 9/5(17) + 32 = 62.6 F.

To know more about celsius please refer:

https://brainly.com/question/14767047

#SPJ4

The uncertainty given as "0.2 cm" in the report represents the precision of the measurement. This type of uncertainty is known as random or statistical uncertainty

Random uncertainty arises as a result of measurement technique limitations, such as the limitations of the measuring instrument or the experimenter's ability to read the instrument. Random uncertainty can be reduced by improving measurement technique or taking more measurements to improve result precision.

The reported value of "23.6 cm" is the best estimate of the true value of the quantity being measured in this case, and the uncertainty of "0.2 cm" indicates the range of values within which the true value is likely to lie. It means that if the measurement were repeated multiple times, the values obtained with a certain level of confidence (typically 95% confidence interval) would be expected to fall within the range of 23.4 cm to 23.8 cm.

For more question on Random uncertainty click on

https://brainly.com/question/2626239

#SPJ4

The third law of motion, also known as the law of action-reaction, states that for every action, there is an equal and opposite reaction.

This implies that there are always two forces acting on the two interacting objects. The first object is subject to a force of similar magnitude to the second object. Force pairs—equal and opposing action-reaction force pairs—always exist in pairs.

For example, when a person jumps up into the air, the ground exerts an equal force in the opposite direction, pushing the person back up into the air. This law can also be applied to a rocket engine, where the exhaust gases being expelled out of the engine cause a reaction force that propels the rocket forward.

To learn more about motion click here https://brainly.com/question/22810476

#SPJ4

The excess charge on the conducting sphere is 3.98×10⁻⁶ C.

Electric potential is a scalar quantity that describes the electrical potential energy per unit charge of a charged object or system. It is also known as voltage and is measured in volts (V).

Electric potential is defined as the work done per unit charge in moving a small positive test charge from an infinite distance to a point in an electric field. It is a measure of the electric potential energy that a unit charge would have if it were placed at that point in the field.

The excess charge on a conducting sphere can be calculated using the formula:

Q = 4πε0R V

Where Q is the excess charge on the sphere, R is the radius of the sphere, V is the potential of the sphere, and ε0 is the permittivity of free space.

Placing the given values into the equation, we get

Q = 4πε0R V

Q = 4π(8.85×10⁻¹² F/m) (0.15m) (1500V)

Q = 3.98×10⁻⁶C

To know more about voltage, visit:

https://brainly.com/question/29445057

#SPJ1

60 kilometers per hour (Km) is equal to 37.28 miles per hour.

Use formula, km/ 1.609 to convert to mph.

Distance is the sum of an object's movements, regardless of direction. Distance can be defined and explained as the amount of space an object has covered, regardless of its starting or ending position.

The pace at which an object's position changes in any direction is referred to as its speed. The distance traveled in the relation to the time it took to travel that distance is how speed is defined. Since speed simply has a direction and no magnitude, it is a scalar quantity. You must always multiply or divide by 1.6 to determine MPH. When moving at 60 km/h, the calculation is 60/1.609344, or 37.28 mph.

Learn more about speed:

brainly.com/question/13943409

#SPJ4

The weight of a cloud can vary widely depending on its size, height, and the amount of moisture it contains, so there isn't a fixed weight for all clouds.

Clouds consist of water droplets or ice crystals that are suspended in the air, so they don't have a specific weight that can be measured. However, the amount of water vapor contained in a cloud can be estimated, and this can be converted to a weight using the density of water. On average, a cumulus cloud weighing about 1 million pounds contains around 100 tons of water.

To know more about the Clouds, here

brainly.com/question/18370044

#SPJ4

Light energy with very low amplitude would be perceived dim.

To the human sight, such low amplitude light energy would appear weak. This is because of the  wave's amplitude, which in the case of light relates to the light's intensity or brightness and t will measure the size of its oscillations.

In other words, as a light wave's amplitude falls, it loses energy and becomes brighter to the eye. This is true because light with a specific range of amplitude and moderate intensity is best perceptible to the human eye. When there is insufficient light that falls outside of this spectrum, it is seen as being faint or invisible.

Learn more about Light energy:

https://brainly.com/question/9444330

#SPJ4

The statement "The transformers step down the voltage from a high of 765 volts to the voltage we use in our houses." is true. Because  Transformers are electrical devices that can step up or step down voltage levels, depending on their design and purpose.

Transformers play a critical role in the safe and efficient distribution of electricity, by enabling power to be transmitted over long distances and used in a variety of applications with different voltage requirements.

In the case of the power grid, large power transformers are used to step up the voltage of the electricity generated at power plants, to reduce losses during long-distance transmission. However, before the electricity can be used in homes and businesses, the voltage must be stepped down to a safe and usable level.

In the United States, the standard voltage for household electrical systems is 120 volts (or 240 volts for larger appliances), so transformers are used to step down the voltage from higher levels, such as the 765 volts mentioned in the question.

To know more about Transformers:

https://brainly.com/question/25438426

#SPJ4