Where flexible tubing is used to enclose the conductors, the tubing shall extend from the last insulating to not less than 6 inches. This requirement is stated in section 314.18(c) of the National Electrical Code (NEC).
Electricity can flow through metals, molten ionic compounds, and electrolyte solutions.
The letters that complete the gaps are;
Non-conductor conductor other than conductorsNon-conductor conductorsConductor DecreasesConductorsBecause there are available free electrons within metals, they act as conductors.
An ionic solid is not a conductor because the ions, which are the charge carriers, are tied together in the lattice.
The crystal breaks apart in the molten state, releasing its ions. The molten ionic material is a conductor as a result.
Because mobile ions are charge carriers in solution, electrolyte solutions like HCl transmit electricity. The number of ions in the solution reduces as the solution's concentration rises.
Learn more about conductors here
https://brainly.com/question/18084972
#SPJ11
The coil that serves the inside of the house in a heat pump is known as the _____ _____.
The coil that serves the inside of the house in a heat pump is known as the evaporator coil/ indoor coil.
In a heat pump system, the indoor coil is an essential component that is responsible for transferring heat between the refrigerant and the indoor air.
Thus, the coil that serves the inside of the house in a heat pump is known as the evaporator coil/ indoor coil.
Know more about the evaporator
https://brainly.com/question/31562018
#SPJ11
Bending radius in type AC shall be made not to be damaged and of the curve of the inner edge of any bend shall not be less than _________ times in diameter of the cable.
325.24
The bending radius in type AC cable should be made to prevent damage, and the curve of the inner edge of any bend should not be less than 5 times the diameter of the cable, as specified in the NEC section 320.24.
Pull the cord to unplug them from the outlet was one of the other answers to the question. Carry them by the cord, option C. D) Keep them close to outlets and on the prevent damage work table in a location that is simple to reach.
Read the manufacturer's directions for proper usage and maintenance of your tools to avoid harm.
These days, tools are pricey. Because of this, if you want to use them for a long time, you must take good care of them and use them appropriately. You must first study the manufacturer's instructions for the use and upkeep of the tool because of its complexity. By doing so, you'll make the most of their potential and employ them more effectively for the right tasks.
Learn more about prevent damage here
https://brainly.com/question/11156977
#SPJ11
This entity is responsible for ensuring the proper and legal incorporation of security considerations:
a. Anti-Terrorism Working Group (ATWG)
b. Anti-Terrorism Officer
c. CI Support Personnel
d. Force Protection Working Group (FPWG)
e. Information Systems Security Managers (ISSM)
f. Installation Commander/Facility Director
g. Law Enforcement Officials
h. Legal Officers
i. Operations Security Officer
j. Physical Security Officer/Provost Marshal
k. Threat Working Group (TWG)
The Physical Security Officer/Provost Marshal is the entity responsible for ensuring the proper identifier and legal incorporation of security considerations.
The entity responsible for ensuring the proper identifier and legal incorporation of security considerations is the Security Enforcement entity, which may include Law Enforcement Officials, the Physical Security Officer/Provost Marshal, the Installation Commander/Facility Director, or the Operations Security Officer. Legal Officers may also provide guidance on the legal aspects of security enforcement. They work closely with law enforcement, operations, and other security-related personnel to maintain the safety and integrity of facilities and installations.
Their responsibilities include the installation, use, and maintenance of security equipment, from metal detectors to electronic monitoring. They may also interact with guests and staff for security reasons. Responsibilities include accessing guest and electronic information and overseeing all security.
Learn more about Identifier:
https://brainly.com/question/31494133
#SPJ11
The output of the counter is energized whenever the accumulated count is less than or equal to the preset count. true/false
The statement "The output of the counter is energized whenever the accumulated count is less than or equal to the preset count" is true because a counter is a digital device that counts the number of input pulses received. It consists of flip-flops, which are interconnected in a specific arrangement to achieve the desired counting sequence.
The counter has an accumulated count, which represents the total number of pulses received thus far, and a preset count, which is a predetermined value that is set by the user.
When the accumulated count is less than or equal to the preset count, the output of the counter is energized, indicating that the desired count has been reached or has not yet been exceeded. This is because the counter's main function is to keep track of the input pulses and provide an output signal when a specific count is achieved. In this case, the counter acts as a comparator, comparing the accumulated count to the preset count, and energizing the output when the condition is met.
To summarize, the output of the counter being energized whenever the accumulated count is less than or equal to the preset count is a true statement, as it accurately describes the behavior of a counter in relation to its accumulated and preset counts. This behavior is essential for various applications, such as measuring the frequency of a signal or controlling the timing of events in a digital system.
You can learn more about the accumulated count at: brainly.com/question/30784277
#SPJ11
If we code a produce/consumer program, which types of communication require us to implement process synchronization?
In a producer/consumer program, the types of communication that require process synchronization are shared resources or data structures, such as buffers or queues.
Step 1: The producer generates data and stores it in a shared buffer or queue. This is a form of communication between producer and consumer.
Step 2: The consumer retrieves data from the shared buffer or queue and processes it.
Step 3: Process synchronization is needed to ensure that the producer and consumer access the shared resource in a mutually exclusive manner, preventing conflicts and data inconsistency.
By implementing process synchronization, you can prevent issues such as overwriting produced data before it is consumed, or consuming data that has not been produced yet. This ensures a smooth communication and coordination between the producer and consumer processes.
Learn more about mutexes here: brainly.com/question/29991385
#SPJ11
During normal operation, from which location do most Cisco routers run the IOS?
During normal operation, most Cisco routers run the IOS (Internetwork Operating System) from the Flash memory location. This is where the IOS image is stored and loaded during the router's boot-up process.
An exclusive operating system known as Cisco IOS (Internetwork Operating System) is used by Cisco Systems' routers and switches. The primary function of Cisco IOS is to facilitate data communication between network nodes. An operating system is a piece of system software that manages the hardware, software, and resources of a computer. Operating systems are used by computers, smartphones, video games, and other devices.
Hardware identification, multiprocessing, protocol, and processor support are all examples of basic operating system support. sharing of software and a printer. sharing a same database and file system. features for access control and user authentication in networks.
A "Network Operating System" is an operating system that includes associated protocols and applications to enable quick and inexpensive communication.
Learn more about internetwork operating system here
https://brainly.com/question/28991932
#SPJ11
This facility access control procedure focuses on the unauthorized removal of government assets from an area; thus, it serves not only as a deterrent, but also as a means for detecting contraband: That is the part of:
This facility's access control procedure is designed to prevent unauthorized individuals from removing government assets from the area.
This procedure acts as both a deterrent and a detection method for contraband. The facility access control procedure you described, which focuses on preventing the unauthorized removal of government assets.
And serves as both a deterrent and a means for detecting contraband, is part of a comprehensive security plan or policy.
Learn more about government click here:
brainly.com/question/9201836
#SPJ11
The overhead service conductors from the last pole or other aerial support to and including the splices, if any, connection to the service-entrance conductors at the building or other structure.
10 def.
The overhead service conductors refer to the wires that are responsible for carrying electrical power from the last pole or aerial support to the building or other structure. These conductors include all the components, including any splices that are used to connect the service-entrance conductors at the building or other structure.
Overall, the structure of these service conductors is an essential aspect of ensuring that electrical service is safely and reliably delivered to homes and businesses.
Overhead support The conductors are those that run from the service point to the building's or other structure's first point of connection to the service-entrance conductors.
A substance or material that allows the passage of power is known as an electric conductor. When voltage is applied, electric charge carriers—typically electrons or ions—move without difficulty from one atom to the next in a conductor.
Conductors are the substances or materials that let energy pass through them. Additionally, conductors allow heat to pass through them. Metals, the human body, the Earth, and animals are some examples of conductors. The body is a powerful conductor.
Learn more about service conductors here
https://brainly.com/question/28298618
#SPJ11
Which types of communication require parent/child process relationship?
The types of communication that require parent/child process relationship are those that involve one process (the parent) spawning another process (the child) and then communicating with it through various means such as shared memory, pipes, or signals.
This type of communication is common in operating systems and software development, where a parent process may need to create and manage multiple child processes to perform specific tasks. Examples of such communication include interprocess communication (IPC), fork-exec model, and client-server architecture.
Hi! In the context of computer systems and programming, the types of communication that typically require a parent/child process relationship are inter-process communication (IPC) methods. These include, but are not limited to, pipes, message queues, shared memory, and sockets. Parent/child processes utilize these IPC methods to exchange information and coordinate their actions effectively.
Learn more about communication here
https://brainly.in/question/32375161
#SPJ11
(590-4(C)) Type NM and NMC cables can be used for temporary wiring in structures of a height of 6 feet, 12 feet, or 18 feet.(True/False)
The answer is False.
According to the National Electric Code (NEC), Type NM and NMC cables are only suitable for use in residential buildings and are not permitted for use in commercial and industrial buildings. Additionally, these cables are not designed for use in temporary installations and are only permitted for permanent installations.
The height of the structure mentioned in the statement (6 feet, 12 feet, or 18 feet) is not relevant to the usage of NM and NMC cables, as these types of cables are designed for permanent wiring in buildings, not for temporary applications. It is crucial to follow the National Electrical Code (NEC) guidelines and other local regulations when using these cables for wiring purposes.
In summary, the statement is false because NM and NMC cables are not intended for temporary wiring and the height of the structure is not relevant to their usage. Remember to always follow electrical codes and safety guidelines when working with wiring and electrical systems.
Learn more National Electric Code here: brainly.com/question/17215290
#SPJ11
the class shirt extends the clothing class. to make the class dressshirt inherit the functionality of both clothing and shirt its class header would be:
Group of answer choices
public class DressShirt inherits Shirt, Clothing
public class DressShirt inherits Shirt
public class DressShirt extends Shirt
public class DressShirt extends Shirt, Clothing
If Shirt inherits Clothing, then Shirt has direct access to the ______ members of Clothing
Group of answer choices
public and protected
public
private
protected
private and protected
Shirt inherits Clothing. What is the first thing that must happen in the Shirt constructor?
Group of answer choices
Initialize the required Shirt fields
Call the Clothing constructor
Create all objects required for Shirt fields
Map the parameters coming into the constructor to Shirt fields
The correct answer for the first question is: public class DressShirt extends Shirt, Clothing. The correct answer for the second question is: protected members of Clothing.
The correct answer for the third question is: Call the Clothing constructor. To make the class DressShirt inherit the functionality of both Clothing and Shirt, its class header would bethe class shirt extends the clothing class. to make the class dress shirt inherit the functionality of both clothing and shirt its class header would be.
public class DressShirt inherits Shirt, Clothing public class DressShirt inherits Shirt public class DressShirt extends Shirtpublic class DressShirt extends Shirt, Clothing. Your answer: public class DressShirt extends Shirt If Shirt inherits Clothing, then Shirt has direct access to the members of Clothing, Your answer: Call the Clothing constructor.
To know more about DressShirt:- https://brainly.com/question/31491617
#SPJ11
The correct answer to the first question is: public class DressShirt extends Shirt, Clothing constructor.
The correct answer to the second question is: public and protected.
The correct answer to the third question is: Call the Clothing constructor.
Learn more about Clothing constructor: https://brainly.com/question/13267121
#SPJ11
Every PLC model offers some form of counter instruction. true/false
True. all PLC models offer some form of counter instruction as it is an essential tool for automation and control.
How to determine PLC models?Programmable Logic Controllers (PLCs) are designed to perform automation tasks and they often need to keep track of various events and processes occurring in a system.
Counters are one of the essential instructions that are used in PLC programming to keep track of such events.
Counters are used to count pulses, events, or other actions, and they are available in various types and forms in different PLC models.
Most PLC models offer some form of counter instruction as it is a fundamental feature in PLC programming.
The counter instruction is used to increment or decrement a counter value based on a specified condition or input signal.
It is an important tool for controlling the flow of the program, and it can be used for a wide range of applications such as counting parts, tracking the number of times a machine has cycled, or monitoring the production rate of a system.
Therefore, it can be concluded that almost all PLC models offer some form of counter instruction as it is an essential tool for automation and control.
Learn more about PLC models
brainly.com/question/30469449
#SPJ11
5204 - The angle of attack at which a wing stalls remains constant regardless of:- Weight, dynamic pressure, bank angle, or pitch attitude-Dynamic pressure, but varies with weight, bank angle, and pitch attitude- Weight and pitch attitude, but varies with dynamic pressure and bank angle
The correct answer is: Dynamic pressure, but varies with weight, bank angle, and pitch attitude.
The angle of attack at which a wing stalls is determined by the dynamic pressure of the air flowing over the wing, which is a function of airspeed and air density. However, this angle can be influenced by other factors such as weight, bank angle, and pitch attitude. For example, a heavier aircraft may require a higher angle of attack to maintain lift, while a steeper bank angle or a nose-up pitch attitude can also increase the angle of attack and potentially lead to a stall. Therefore, while dynamic pressure is the primary factor determining the stall angle, it is also affected by other variables. The angle of attack at which a wing stalls remains constant regardless of weight, dynamic pressure, bank angle, or pitch attitude.
Learn more about density here-
https://brainly.com/question/29775886
#SPJ11
A sine wave has two maximum points (peaks) in one cycle.
How many maximum points does a sine wave have during one cycle?
A sine wave has two maximum points (peaks) during one cycle: one positive maximum and one negative maximum.
A sine wave's peak to peak value is twice its peak value. As a result, the waveform's total peak to peak value is 2 x 80 VAC, or 160 VAC.
A sine wave's peak to peak value is a crucial indicator of the waveform's amplitude. It is determined by multiplying the waveform's peak value by two. Given that the peak value of this specific waveform is 80 VAC, its peak to peak value is 2 x 80 VAC, or 160 VAC. This peak to peak value represents the total number of voltage swings experienced by the waveform from its base to its crest. This waveform's peak to peak value is a helpful
Learn more about peaks here
https://brainly.com/question/30491931
#SPJ11
A restricted area must be properly marked to inform personnel they are in the vicinity of a restricted area. True or False?
Answer : True. A restricted area must be properly marked to inform personnel they are in the vicinity of a restricted area. This helps to ensure that personnel are aware of the potential risks and take appropriate precautions while working in that area.
The majority of earthquake zones are distributed near or at tectonic plate boundaries, frequently in vicinity clusters. Most earthquakes are located within the Pacific Ocean's Ring of Fireplaces. Convergent or conservative barriers are linked to earthquakes that are most effective.
The majority of earthquakes will occur near any type of plate border. Massive earthquakes frequently begin at the plate boundaries. Around the arena, there could be an earthquake belt where plate motion causes earthquakes to rise. When tension or electricity is released from the crust, an earthquake is caused.
On the ridges, there seem to be a lot of shallow earthquakes. They are usuallyb, orange or yellow in colour, and shallow in depth.
Learn more about vicinity here
https://brainly.com/question/28542752
#SPJ11
his voltage reading was obtained while cranking the engine. the indicated reading (0.816 v) is _
The voltage reading was taken while cranking the engine, and the indicated reading was 0.816 volts. To provide an explanation with the terms:
When cranking the engine, the starter motor requires a certain amount of voltage to function properly. The voltage reading of 0.816 volts indicates the electrical potential difference present at that specific point during the engine cranking process.
To determine whether this voltage reading is within the acceptable range, you would need to compare it to the manufacturer's specifications for the particular engine being tested. If the reading is within the specified range, the engine's electrical system is functioning properly. If it is outside the acceptable range, further investigation may be required to identify any potential issues with the engine's electrical components.
Learn more about voltage here:
brainly.com/question/2364325
#SPJ11
Hi! Based on the information provided, the voltage reading obtained while cranking the engine was 0.816V. This indicated reading signifies the voltage level present during the engine cranking process.
Learn more about cranking the engine: https://brainly.com/question/14800055
#SPJ11
Where the number or current- carrying conductors in a raceway or cable, when it exceeds the allowable ampacity of each conductor it shall be ________.
310.15(b)(3)
Where the number or current-carrying conductors in a raceway or cable, when it exceeds the allowable ampacity of each conductor it shall be derated. This is stated in section 310.15(b)(3) of the National Electrical Code (NEC).
Current-carrying conductor: a conductor which carries the electric current under normal conditions [this term is defined in the IEC TS 62257-5-2015].Current-carrying conductor: a conductor which carries the electric current under normal conditions [this term is defined in the IEC TS 62257-5-2015].
Note 1 to entry: The line conductor (L), the neutral conductor (N), the mid conductor (M), the PEN conductor, the PEM conductor and the PEL conductor are the current-carrying conductors. The protective conductor (PE) is not the current-carrying conductor.
A protective conductor under normal conditions conducts almost no electric current, because there are no faults and no induced currents, such as earth fault currents. Therefore, it is not considered a current-carrying conductor and is not included in the total number of conductors in electrical circuits, networks and systems.
learn more about raceway here:
https://brainly.com/question/30821238
#SPJ11
For a dwellign unit, the minimum size aluminum service entrance conductor permitted for a 100 amps service number zero _________ awg
310.15(b)(7)
For a dwelling unit, the minimum size aluminum service entrance conductor permitted for a 100-amp service is No. 1/0 AWG.
The table provides the minimum allowable ampacity for conductors of various materials and sizes. For a 100-amp service, the minimum allowable ampacity is 100 amperes, and the minimum conductor size for aluminum conductors is No. 1/0 AWG. It is important to note that the size of the service entrance conductor may also be influenced by factors such as the length of the run, voltage drop, and ambient temperature, among others. These factors may require a larger conductor size than the minimum required by the NEC to ensure safe and efficient operation of the electrical system.
Learn more about 100-amp service here:
https://brainly.com/question/27380344
#SPJ11
Which mathematical operator is used to raise five to the second power in Python? /
**
^
In Python, the mathematical operator used to raise five to the second power is the double asterisk (**). Your expression would look like this:5 ** 2`
Python is a high-level, interpreted programming language used for a wide range of applications, including web development, data analysis, artificial intelligence, and scientific computing. It has a simple and concise syntax, making it easy to learn and use, while also providing powerful programming capabilities. Python's standard library includes modules for tasks such as file I/O, regular expressions, and networking, while its extensive third-party library ecosystem offers a wealth of additional functionality. Python is an open-source language, which means that it is free to use, distribute, and modify. Its popularity has grown rapidly in recent years due to its ease of use, versatility, and large and supportive community of developers and users.
Learn more about Python here:
https://brainly.com/question/30365096
#SPJ11
Each of the following class declarations has errors. Locate as many as you can. 63. class Yard { private: float length; public: yard(float l) { length = l; } // float conversion function void operator float() { return length; } ... Other member functions follow ...};
The errors in the given class declaration. Here are the issues : 1. The constructor has a typo in its name. It should be "Yard" instead of "yard" to match the class name, 2. The function signature for the conversion operator should be "operator float()" instead of "void operator float()". The return type should be float, not void.
Here's the corrected version of the class declaration:
```cpp
class Yard {
private:
float length;
public:
Yard(float l) { length = l; } // corrected constructor name
// corrected return type for conversion function
operator float() { return length; }
// ... Other member functions follow ...
};
```
To learn more about Class declaration Here:
https://brainly.com/question/30700632
#SPJ11
EMT smaller than ________ inch shall not be used.
EMT smaller than a specific inch size shall not be used when the conduit does not meet the required minimum diameter for a particular application. It is important to refer to the applicable code or standard for the minimum diameter requirement in your specific situation.
Emergency Medical Technicians provide out of hospital emergency medical care and transportation for critical and emergent patients who access the emergency medical services (EMS) system. EMTs have the basic knowledge and skills necessary to stabilize and safely transport patients ranging from non-emergency and routine medical transports to life threatening emergencies. Emergency Medical Technicians function as part of a comprehensive EMS response system, under medical oversight. Emergency Medical Technicians perform interventions with the basic equipment typically found on an ambulance. Emergency Medical Technicians are a critical link between the scene of an emergency and the health care system.
learn more about EMT here:
https://brainly.com/question/14642620
#SPJ11
Which router interface should be used for direct remote access to the router via a modem?
The router interface that should be used for direct remote access to the router via a modem is typically the console port.
The router interface that should be used for direct remote access to the router via a modem is typically the console port. This interface allows for direct access to the router's command-line interface (CLI) and can be used to configure the router remotely. It is important to note that the console port is typically used for initial configuration and troubleshooting, and remote access should be secured using appropriate authentication and encryption methods to prevent unauthorized access.
Learn more about remote access here
https://brainly.com/question/28900477
#SPJ11
A network technician is investigating network connectivity from a PC to a remote host with the address 10.1.1.5. Which command issued on the PC will return to the technician the complete path to the remote host?
To investigate network connectivity from a PC to a remote host with the address 10.1.1.5, the network technician should use the `tracert` command (on Windows) or `traceroute` command (on Linux and macOS).
This command will return the complete path to the remote host by displaying all intermediate hops between the PC and the remote host. The command that the network technician can use to trace the complete path to the remote host with the IP address 10.1.1.5 from the PC is "tracert 10.1.1.5". This command will provide a detailed report of the network route taken by the packets to reach the destination, including each hop, the time taken to reach each hop, and the IP address of each device on the way to the remote host.
Learn More about Linux here :-
https://brainly.com/question/30176895
#SPJ11
In normal use, the down counter is used in conjunction with the up counter to form an up/down-counter. true/false
In the new service or product development​ process, the design stage is critical because it
In the new service or product development process, the design stage is critical because it establishes the blueprint for the entire service or product, ensuring its functionality, appeal, and efficiency. This stage involves refining ideas, conducting research, and developing prototypes, ultimately setting the foundation for successful development and launch of the service or product.
In the new service or product development process, the design stage is critical because it lays the foundation for the entire project. This is where the team determines the overall look and feel of the service or product and ensures it aligns with the company's brand and mission. The design stage also involves making important decisions about the functionality and usability of the service or product. If any flaws or issues are identified at this stage, they can be addressed before moving forward with development. Therefore, the design stage is essential to the success of the overall service or product development process.
Learn more about aligns here-
https://brainly.com/question/14396315
#SPJ11
The​ _______ the supply​ chain, the less predictable the likelihood and the impact of a​ disruption, and the greater the risk to the effectiveness of the supply chain.
The longer the length of the supply chain, the less predictable the likelihood and the impact of a disruption, and the greater the risk to the effectiveness of the supply chain.
The longer the supply chain, the less predictable the likelihood and impact of a disruption, and the greater the risk to the effectiveness of the supply chain. This is because as the supply chain becomes longer, it involves more stages and parties, such as suppliers, manufacturers, distributors, and retailers, which increases the complexity of the system and makes it more vulnerable to disruptions. For example, if a supplier in a long supply chain experiences a disruption, it can cause delays in the production process, which can lead to a shortage of goods, increased costs, and lower customer satisfaction. These disruptions can be caused by a variety of factors, such as natural disasters, transportation issues, labor strikes, and supplier bankruptcy, among others.
Learn more about bankruptcy here-
https://brainly.com/question/15277574
#SPJ11
Vaults have reinforced concrete walls, ceilings, and floors, and have a hardened steel door:
The use of reinforced concrete walls, ceilings, and floors in vaults is intended to provide extra strength and durability.
This construction method involves adding additional steel bars or mesh to the concrete mix to improve its tensile strength, which makes it more resistant to cracking and breaking under pressure. Similarly, the hardened steel door is designed to withstand significant force or impact, making it virtually impenetrable. Overall, the combination of reinforced concrete and hardened steel makes vaults extremely secure and difficult to breach.
To learn more about vaults click the link below:
brainly.com/question/26255180
#SPJ11
The compound beam shown in figure is pin connected at B. Determine the components of reaction at its supports. Neglect its weight and thickness.
The values based on the information given will be Ra = 1000N and Rc= 90N
What is weight?Weight refers to the measure of the force of gravity on an object, and is typically measured in units of mass, such as kilograms or pounds. Weight is influenced by the mass of the object and the strength of the gravitational field it is in.
Thickness, on the other hand, refers to the measure of how thick an object is, or the distance between opposite surfaces of an object. Thickness is typically measured in units of length, such as millimeters or inches.
While weight and thickness are not directly related to each other, they can both play important roles in determining the properties and uses of an object. For example, a thin piece of metal may be lightweight, but may not be strong enough to support heavy loads. Conversely, a thicker piece of metal may be heavier, but may be able to support heavier loads due to its increased strength.
Learn more about thickness on
https://brainly.com/question/4937019
#SPJ1
The counter reset (RES) instruction, it is always given the same address as the counter it is to reset. true/false
The given statement "The counter reset (RES) instruction, it is always given the same address as the counter it is to reset." is true because the counter reset (RES) instruction is always given the same address as the counter it is to reset.
The RES instruction is used to reset the current value of a counter to its initial value, which is typically set to 0 or another predetermined value. In order to reset a specific counter, the RES instruction must be addressed to the same memory address as the counter. This ensures that the instruction is applied to the correct counter and that it resets the counter to the correct initial value. Therefore, the statement "the counter reset (RES) instruction is always given the same address as the counter it is to reset" is true.
You can learn more about RES instruction at
https://brainly.com/question/31568319
#SPJ11
(358-26) A run of electrical metallic tubing between outlet boxes shall not exceed _____ close to the box.
The National Electric Code (NEC) states that a run of electrical metallic tubing between outlet boxes shall not exceed 3 feet close to the box.
This is to ensure safe and efficient electrical wiring installation. It is important to follow these guidelines to prevent electrical hazards and ensure compliance with local building codes. If too many wires are installed in a conduit, the conduit can become overheated, which could create a fire hazard. The maximum length limit helps ensure that there is adequate space in the conduit for the wires, which in turn helps prevent overheating.It's worth noting that the maximum wire fill rule for EMT conduit is not the only requirement for conduit installations in the NEC. Other requirements include rules for minimum conduit size, maximum conduit fill, and proper installation techniques to ensure the conduit is securely fastened and protected from damage. These requirements are all aimed at ensuring the safety and reliability of electrical wiring installations.
Learn more about electrical here
https://brainly.in/question/47308007
#SPJ11