When a series LRC circuit is driven at its resonance frequency, the phase difference between the drive voltage and the voltage across the resistor will be 0 degrees.
Solution - Resonant frequency is the natural frequency where a medium vibrates at the highest amplitude. Resonant frequency is usually denoted as f0. Resonance is witnessed in objects in equilibrium with acting forces and could keep vibrating for a long time under perfect conditions. This is because, at resonance, the inductive and capacitive reactances cancel each other out, resulting in a purely resistive circuit where the voltages across the resistor and the source are in phase.
To learn more about resonance frequency -
brainly.com/question/13040523
#SPJ11
Question 38 Marks: 1 Water in wading pools should be completely recirculated everyChoose one answer. a. 1 to 2 hours b. 12 hours c. 6 hours d. 24 hours
The correct answer is c. 6 hours. Water in wading pools should be completely recirculated every 6 hours to maintain safe and clean water conditions for children. This helps to prevent the growth of harmful bacteria and other contaminants.
Wading pools are shallow pools typically used by children for play and recreation. Because the water in these pools is often not treated with chemicals like chlorine, it is important to ensure that the water is recirculated frequently to maintain its cleanliness and prevent the spread of waterborne illnesses. According to industry standards and guidelines, the water in wading pools should be completely recirculated every 6 hours. This helps to ensure that the water is adequately filtered and treated, and that any contaminants or bacteria are removed before they can cause harm to swimmers.
Learn more about wading pools here:
https://brainly.com/question/28780998
#SPJ11
Conductors in Parallel(310-10(H)(5): All parallel equipment grounding conductors are required to be a minimum No. 1/0.(True/False)
All parallel equipment grounding conductors must be a minimum No. 1/0 according to the code 310-10(H)(5). The answer is: False. The code 310-10(H)(5) does not specify a minimum No. 1/0 size for parallel equipment grounding conductors. It is important to follow the specific code requirements for conductor sizing in parallel installations.
According to NEC 310-10(H)(5), parallel equipment grounding conductors are not required to be larger than No. 1/0 unless they are part of a feeder or service entrance, in which case they must be at least the same size as the largest ungrounded conductor. However, it is recommended to use the same size equipment grounding conductors in parallel to simplify installation and minimize impedance differences between the conductors.
To know more about grounding conductors, please click on:
https://brainly.com/question/14405035
#SPJ11
Due to the wave nature of light, light shined on a single slit will produce a diffraction pattern. Green light (570 nm) is shined on a slit with width 0.465 mm. (a) Find the width of the central maximum located 1.80 m from the slit. mm (b) What is the width of the first order fringe
(a) The width of the central maximum is 3.75 mm. (b) The width of the first order fringe is 1.87 mm.
(a) The width of the central maximum can be found using the formula:
w = (λL) / D
where w is the width of the central maximum, λ is the wavelength of light, L is the distance from the slit to the screen, and D is the width of the slit.
Substituting the given values, we get:
w = (570 × 10⁻⁹ m × 1.80 m) / 0.465 × 10⁻³ m = 3.75 mm
Therefore, the width of the central maximum is 3.75 mm.
(b) The width of the first order fringe can be found using the formula:
w = (λL) / d
where w is the width of the first order fringe, λ is the wavelength of light, L is the distance from the slit to the screen, and d is the distance from the central maximum to the first order fringe.
To find d, we can use the small angle approximation:
sinθ ≈ θ ≈ d/L
where θ is the angle between the central maximum and the first order fringe.
Substituting the given values, we get:
θ = d/L = 1.87 × 10⁻³ m / 1.80 m ≈ 0.00104 radians
Using the same formula as part (a), we can find the width of the first order fringe:
w = (570 × 10⁻⁹ m × 1.80 m) / 0.00104 = 1.87 mm
Therefore, the width of the first order fringe is 1.87 mm.
learn more about wavelength here:
https://brainly.com/question/13533093
#SPJ11
c) What if nonconservative forces, such as friction, also act within the system? In that case, the total mechanical energy will change. The law of conservation of energy is then written as
The law of conservation of energy is then written as the totals mechanical energy of a system, including any nonconservative forces, is conserved only if the work done by nonconservative forces is equal to the change in mechanical energy.
The law of conservation of energy states that the total energy in a system is constant, meaning that energy cannot be created or destroyed, only transferred or converted from one form to another.
However, in the presence of nonconservative forces like friction, the total mechanical energy of the system will change over time.
In such cases, the law of conservation of energy is modified to state that the total energy of the system, including both kinetic and potential energy, is conserved, but the sum of the kinetic and potential energy may decrease due to energy lost as heat or work done against nonconservative forces.
Learn more about nonconservative forces at
https://brainly.com/question/30045046
#SPJ4
(240) What size overcurrent protection device is required for a 45 ampere continuous load? The circuit is in a raceway with 14 current carrying conductors.
For a 45A continuous load in a circuit with 14 current-carrying conductors, a 60A overcurrent protection device is required (NEC guidelines).
To decide the size of the overcurrent security gadget expected for a 45-ampere nonstop burden in a circuit with 14 current-conveying guides, you want to think about two factors: the consistent burden and the quantity of current-conveying guides.
According to NEC rules, for a nonstop burden, the overcurrent security gadget ought to be evaluated no less than 125% of the heap, which for this situation would be:
125% x 45 amps = 56.25 amps
Furthermore, for a circuit with multiple current-conveying guides, the ampacity of the guides should be changed by a derating factor. According to NEC Table 310.15(B)(3)(a), when there are 14 current-conveying guides in a raceway, the derating factor is 70%. Subsequently, the changed ampacity of the guides would be:
45 amps x 0.7 = 31.5 amps
Since the changed ampacity of the guides is not exactly the base required size of the overcurrent assurance gadget (56.25 amps), the base size overcurrent insurance gadget expected for this circuit would be 60 amps.
To learn more about overcurrent protection device, refer:
https://brainly.com/question/29570626
#SPJ4
A man drops a cup from cretain height which breaks in to pieces what's energy changes are involved?
There are various energy changes that occur when a guy drops a cup from a specific height. The cup's elevation above the ground gives it potential energy.
This potential energy is transformed into kinetic energy, the energy of motion, as it descends. The kinetic energy is transmitted to the cup as it falls to the ground, breaking it into pieces. This process involves the conversion of kinetic energy into thermal energy from the collision and friction of the shattered pieces with the ground as well as potential energy of the broken pieces. When a cup breaks, energy is released in the form of sound waves, which are then transmitted from the cup to the surrounding air.
To know more about potential energy, here
brainly.com/question/24284560
#SPJ1
31) Where does most star formation occur in the Milky Way today? A) in the halo B) in the bulge C) in the spiral arms D) in the Galactic center E) uniformly throughout the Galaxy
Most star formation in the Milky Way Galaxy today occurs in the Galactic spiral arms. These arms are regions of high density and concentration of gas and dust, which are necessary for the formation of stars.
As the Milky Way rotates, the spiral arms move through the Galaxy, sweeping up gas and dust and triggering the formation of new stars. The Galactic center is also a region of active star formation, but the conditions there are much more extreme and only certain types of stars can form. In contrast, the spiral arms offer a more conducive environment for a wider range of stars to form. Overall, star formation in the Milky Way is a complex and ongoing process, influenced by a variety of factors such as density, temperature, and chemical composition of the interstellar medium. Studying the locations and characteristics of star formation in the Galaxy can provide valuable insights into the evolution of our Galactic neighborhood and the formation of our own Solar System.
learn more about galaxy here
https://brainly.com/question/12532606
#SPJ11
2. Globalization implies all of the following except:
a. the world is free from national boundaries
b. a borderless world
c. competition between workers from other countries
d. an organization's nationality is held strongly in consciousness
The correct answer is d. an organization's nationality is held strongly in consciousness. Globalization is the process of increasing interconnectedness and interdependence among individuals, businesses, and countries worldwide.
It involves the breaking down of national boundaries and creating a borderless world where goods, services, and people can move freely. As a result, there is increased competition between workers from different countries, but the emphasis on an organization's nationality is reduced in the face of globalization.
Globalization implies all of the following except
d. an organization's nationality is held strongly in consciousness
To know more about Organization's click here .
brainly.com/question/13278945
#SPJ11
Question 3 Marks: 1 In practice, exposure to all ionizing radiation is controlled by the use of shields of lead.Choose one answer. a. True b. False
True, exposure to all ionizing radiation is controlled by the use of shields of lead.
Ionizing radiation is a form of energy that acts by removing electrons from atoms and molecules of materials that include air, water, and living tissue. Ionizing radiation can travel unseen and pass through these materials. Ionizing radiation, including nuclear radiation, consists of subatomic particles or electromagnetic waves that have sufficient energy to ionize atoms or molecules by detaching electrons from them.
Learn more about electrons here: https://brainly.com/question/1255220
#SPJ11
a heat engine operates by group of answer choices usually having an efficiency equal to the maximum efficiency. transferring energy from a hot reservoir to a cold reservoir. always having an efficiency of 100% to conserve energy. usually having an efficiency less than the maximum efficiency. using a temperature difference between two thermal reservoirs.
The heat engine operates by using a temperature difference between two thermal reservoirs and transferring energy from a hot reservoir to a cold reservoir. Usually, the efficiency of a heat engine is less than the maximum efficiency, which is the theoretical limit for the efficiency of the engine.
The important to keep the engine operating within a safe temperature range to prevent damage or failure. A heat engine operates by using a temperature difference between two thermal reservoirs, transferring energy from a hot reservoir to a cold reservoir. In this process, it usually has an efficiency less than the maximum efficiency, as no engine can achieve 100% efficiency due to energy losses, primarily in the form of heat.
learn more about engine here.
https://brainly.com/question/29011178
#SPJ11
As net filtration pressure increases, the GFR ______. Multiple choice question. doesn't change increases decreases
As net filtration pressure increases, the GFR increases.
GFR (Glomerular Filtration Rate) is the rate at which blood is filtered through the kidneys. Net filtration pressure is the sum of forces that promote or oppose filtration in the glomerulus of the kidney.
The formula for GFR is GFR = Kf x net filtration pressure, where Kf is the filtration coefficient. An increase in net filtration pressure will increase the GFR, while a decrease in net filtration pressure will decrease the GFR. This is because an increase in net filtration pressure will result in a greater force pushing fluid out of the glomerulus and into the Bowman's capsule, leading to an increased rate of filtration.
Conversely, a decrease in net filtration pressure will result in a weaker force pushing fluid out of the glomerulus, leading to a decreased rate of filtration. Therefore, as net filtration pressure increases, the GFR increases.
The GFR (glomerular filtration rate) is the amount of fluid filtered by the glomeruli per unit time. The net filtration pressure is the pressure gradient that drives fluid filtration across the glomerular capillaries. It is determined by the balance between the hydrostatic pressure in the glomerular capillaries and the opposing forces of the osmotic and hydrostatic pressures in the Bowman's capsule.
When the net filtration pressure increases, it leads to an increase in the GFR. This is because a higher pressure gradient across the glomerular capillaries favors the movement of fluid and solutes out of the blood and into the Bowman's capsule, leading to an increase in filtration. Conversely, a decrease in net filtration pressure would lead to a decrease in GFR.
learn more about blood here:
https://brainly.com/question/26557101
#SPJ11
Question 20
Which one of the following is potentially the most important in terms of global warming?
a. carbon dioxide
b. nitrous oxide
c. methane
d. chlorofluorocarbons
The correct answer is c. methane. While carbon dioxide is the most abundant greenhouse gas, methane is much more potent, with a global warming potential 28 times greater than carbon dioxide over a 100-year period.
Methane is produced by a variety of sources, including natural wetlands, livestock, landfills, and fossil fuel production. Reducing methane emissions is a crucial step in mitigating the effects of global warming.
Potentially, methane (c) can be considered the most important in terms of global warming due to its high heat-trapping capacity, although carbon dioxide is the most abundant greenhouse gas.
To know more about Methane click here .
brainly.com/question/2127750
#SPJ11
Answer:
chlorofluorocarbons (CFCs)
Explanation:
It has the highest GWP (Global Warming Potential). Got it right!
Have a good one!
these columns go deep into the ground, connecting the earth to the sky, forming the axis of the universe. a. the wheel of the law b. columns of ashoka c. the cosmic mountain d. columns of kanishka
The columns that go deep into the ground, connecting the earth to the sky and forming the axis of the universe are the cosmic mountain.
In Hindu mythology, the cosmic mountain, known as Mount Meru, is believed to be the center of the universe and is connected to the heavens and the earth. It is said to be so tall that its peak reaches the heavens, and so deep that its roots go all the way to the underworld. The cosmic mountain is often depicted in art and architecture, including the columns of ancient Indian emperors.
Therefore, the columns mentioned in the question, including the wheel of the law, columns of Ashoka, and columns of Kanishka, are not the columns that connect the earth to the sky and form the axis of the universe. Instead, it is the cosmic mountain that holds this significance in Hindu mythology.
To know more about universe, visit;
https://brainly.com/question/28365362
#SPJ11
The Ptolemaic model probably persisted for all these reasons EXCEPT:
A. It had the authority of aristotle behind it
B. It explain why stellar parallax was not observed by the greeks
C. It used perfect circles, which appealed to geometry.
D. It was consistent with the doctrines of the catholic church.
E. It accounted well for galileo's observations of the phase cycle of venus
E. It accounted well for Galileo's observations of the phase cycle of Venus. It accounted well for Galileo's observations of the phase cycle of Venus. The Ptolemaic model was an Earth-centered model of the universe that persisted for centuries despite its inaccuracies.
It was supported by Aristotle's authority and its use of perfect circles in its geometry. Additionally, it was consistent with the doctrines of the Catholic Church. However, it was unable to explain why stellar parallax was not observed by the Greeks. This fact was eventually used as evidence to support the heliocentric model of the universe proposed by Copernicus. Although Galileo's observations of the phase cycle of Venus were significant in advancing the heliocentric model, they were not a reason for the persistence of the Ptolemaic model.
Find out more about the Ptolemaic model.
brainly.com/question/30666789
#SPJ11
A force of 186 N acts on a 7.3 kg bowling ball for 0.40 s. What is the ball’s change in momentum
A force of 186 N acts on a 7.3 kg bowling ball for 0.40 s. then the ball’s change in momentum is 74.4 Ns.
Momentum is defined as mass times velocity. it tells about the moment of the body. it is denoted by p and expressed in kg.m/s. mathematically it is written as p = mv. A body having zero velocity or zero mass has zero momentum. its dimensions is [M¹ L¹ T⁻¹]. Momentum is conserved throughout the motion. According to conservation law of momentum initial momentum is equal to final momentum.
Change in momentum with respect to time is force,
F = Δp/Δt
Hence change in momentum is equal to,
Δp=F ×Δt
Δp= 186 × 0.40
Δp= 74.4 Ns
To know more about Force :
https://brainly.com/question/13191643
#SPJ1.
What type of electromagnetic radiation is light with a wavelength of 10 meters? Use the electromagnetic spectrum show.
The type of electromagnetic radiation is Radiowaves which have a wavelength of 10 meters.
Since these waves have a longer wavelength, they are used for communication over long distances. Some examples of sources that emit these radiations - radiowaves - are TV and radio stations, cell phone towers, as well as satellites.
Radio waves are very beneficial as they can travel long distances without any power losses and getting absorbed or scattered by the atmosphere. Also, radio waves are non-ionizing and generally considered safe for human exposure. They are widely used in many applications, including broadcasting, navigation, remote sensing, and medical imaging.
For more info on electromagnetic radiation visit,
https://brainly.com/question/10759891
#SPJ4
Question: Does the length of the paper helicopter rotors effect the speed at which it falls to the ground? (Don't answer this!)
Real question: what are 4 constants? (what must remain the same)
There are many constants in mathematics and physics, but here are four commonly known ones:
The speed of light in a vacuum, denoted by "c", which is approximately 299,792,458 meters per second.The gravitational constant, denoted by "G", which is approximately 6.674 x 10^-11 cubic meters per kilogram per second squared.Avogadro's number, denoted by "N_A", which is approximately 6.022 x 10^23 particles per mole.Planck's constant, denoted by "h", which is approximately 6.626 x 10^-34 joule-seconds.What are constants?In mathematics and science, a constant is a value that does not change during a particular calculation, process, or experiment. Constants can be either numerical values, such as pi (π) or the number e, or they can be physical or mathematical properties that remain fixed throughout a particular system or equation.
Learn about gravitational constant here https://brainly.com/question/29840517
#SPJ1
Question 39 Marks: 1 Isotopes of the same element haveChoose one answer. a. the same mass number but different atomic numbers b. the same atomic number but different mass numbers c. different atomic and mass numbers d. the same atomic and mass numbers
Isotopes of the same element have: b. the same atomic number but different mass numbers.
Isotopes are versions of the same element that have the same number of protons (which determines the atomic number) but different numbers of neutrons. This results in different mass numbers for each isotope since the mass number is the sum of protons and neutrons in an atom. However, the number of neutrons in the nucleus can vary, and therefore the mass number (number of protons plus number of neutrons) of the isotope is different. Therefore, isotopes of the same element have the same atomic number, but different mass numbers.
To learn more about isotopes click here https://brainly.com/question/21536220
#SPJ11
Question 21
The major impact of global warning would most likely be in:
a. a general decrease in human skin cancer
b. an increase in human skin cancer
c. an alteration of world-wide rainfall
d. a melting in the polar cap
The correct answer is option c, an alteration of world-wide rainfall. Global warming can lead to changes in weather patterns and precipitation, causing alterations in rainfall levels and distribution.
It can also lead to melting of glaciers and ice caps, which can contribute to sea level rise and affect rainfall patterns. While skin cancer rates can potentially be impacted by global warming due to increased exposure to UV radiation, it is not the major impact that would be expected. Melting of the polar cap is a consequence of global warming.
The major impact of "global warming" (not "global warning") would most likely be in:
d. a melting of the polar ice caps.
While global warming can also have effects on skin cancer rates and rainfall patterns, the most significant and widely recognized impact is the melting point .
To know more about Global warming click here .
brainly.com/question/12908180
#SPJ11
Question 33
The green pages of the emergency response guidebook lists a. EPA hazardous materials personnel
b. hazardous materials in alphabetical order
c. initial isolation and protective action distances
d. hazardous material by ID number
The green pages of the Emergency Response Guidebook list hazardous materials by ID number.
Therefore the answer is d) hazardous material by ID number.
The Emergency Response Guidebook (ERG) is a guidebook developed jointly by the US Department of Transportation (DOT), Transport Canada, and the Secretariat of Communications and Transportation of Mexico. The ERG provides guidance for first responders and emergency personnel who may be called upon to deal with hazardous materials incidents during transport.
The guidebook is divided into color-coded sections, with the green pages providing information on specific hazardous materials. These pages list the hazardous materials by their ID number, which is a unique four-digit number assigned by the DOT to each hazardous material.
The ID number provides information on the specific hazards posed by the material, as well as guidance on appropriate response actions, initial isolation and protective action distances, and other important information.
The green pages also provide information on the appropriate response actions for different situations, such as fire, spill, or leak, and provide guidance on protective clothing and equipment, evacuation, and decontamination.
To know more on Emergency Response Guidebook
https://brainly.com/question/28433446
#SPJ4
The green pages of the emergency response guidebook list initial isolation and protective action distances for hazardous materials. They don't list hazardous materials in alphabetical order, by ID number or EPA hazardous materials personnel.
Explanation:The green pages of the emergency response guidebook provide detailed information about initial isolation and protective action distances. These pages are crucial in the event of a hazardous material incident, allowing responders to quickly determine the necessary steps to isolate the hazardous area and protect individuals in the vicinity. The green pages do not list hazardous materials in alphabetical order, by ID number, or EPA hazardous materials personnel. Instead, they focus solely on providing guidance for initial isolation and protective action distances.
Learn more about emergency response guidebook here:https://brainly.com/question/31762108
#SPJ11
The accumulated count of a CTU counter:a. increments with each true-to-false transitionb. decrements with each true-to-false transitionc. decrements with each false-to-true transitiond. increments with each false-to-true transition.
The accumulated count of a CTU (Count Up) counter is a measure of the number of true-to-false transitions that have occurred. This means that for each true-to-false transition, the count is incremented by one. Therefore, option (a) is the correct answer.
It is important to note that the CTU counter is a type of counter in programmable logic controllers (PLCs) that counts the number of transitions from true to false of its input signal.
When the input signal changes from true to false, the count is incremented by one. The accumulated count can be reset to zero by a reset instruction or by powering off the PLC.
On the other hand, the CTD (Count Down) counter is a type of counter that counts the number of false-to-true transitions of its input signal. In this case, the count is decremented by one for each false-to-true transition.
In summary, the accumulated count of a CTU counter increments with each true-to-false transition, whereas the accumulated count of a CTD counter decrements with each false-to-true transition.
Understanding the difference between these two types of counters is important when designing and programming PLCs for industrial automation applications.
For similar question on accumulated count
https://brainly.com/question/31568302
#SPJ11
in the electroplating of nickel, 0.200 faraday of electrical charge is passed through a solution of niso4. what mass of nickel is deposited?a 2.94 gb 5.87 gc 11.7 gd 58.7 ge 294 g
The mass of the nickel deposited is 5.87 g. The correct option is B.
To determine the mass of nickel deposited during the electroplating process, we can use the formula:
mass = (moles of electrons) × (molar mass of nickel) × (Faraday constant)
First, we need to find the moles of electrons. As 1 mole of electrons is equal to 1 Faraday, in this case, 0.200 Faraday of electrical charge corresponds to 0.200 moles of electrons.
Now, we need to find the molar mass of nickel. The atomic mass of nickel (Ni) is approximately 58.7 g/mol.
For the electroplating of nickel from NiSO₄, the balanced equation is:
Ni²⁺(aq) + 2e⁻ → Ni(s)
From the equation, we can see that 1 mole of nickel ions (Ni²⁺) requires 2 moles of electrons to form 1 mole of nickel metal (Ni).
Next, we will calculate the moles of nickel deposited:
moles of Ni = (moles of electrons) / 2
moles of Ni = 0.200 moles / 2 = 0.100 moles
Now we can calculate the mass of the nickel deposited:
mass = (moles of Ni) × (molar mass of nickel)
mass = (0.100 moles) × (58.7 g/mol) = 5.87 g
to know more about electroplating refer here:
https://brainly.com/question/20112817#
#SPJ11
To determine the mass of nickel deposited in the electroplating process, we need to use the equation:
mass of substance = (current x time x atomic mass) / (faraday's constant x valency)
In this case, we know that 0.200 faraday of electrical charge is passed through the solution of NiSO4. We also know that the valency of nickel is 2 (since NiSO4 contains one nickel ion with a +2 charge). The atomic mass of nickel is 58.69 g/mol. Faraday's constant is 96,485 C/mol.
So, plugging in the values we get:
mass of nickel = (0.200 x 1 x 58.69) / (96,485 x 2)
mass of nickel = 0.000608 g
However, the answer options given are in grams, so we need to convert our answer to grams:
mass of nickel = 0.000608 g = 0.608 mg = 0.000000608 g
Therefore, the correct answer is (d) 58.7 g.
In the electroplating of nickel, 0.200 Faraday of electrical charge is passed through a solution of NiSO4. The mass of nickel deposited can be calculated using Faraday's law of electrolysis.
First, we need to find the molar equivalent of 0.200 Faraday of charge. One Faraday is equivalent to the charge of one mole of electrons (approximately 96,485 C/mol). So, 0.200 Faraday is equivalent to 0.200 moles of electrons.
NiSO4 dissociates into Ni²⁺ and SO₄²⁻ ions in the solution. Nickel has a charge of +2, so one mole of nickel ions requires two moles of electrons for reduction (Ni²⁺ + 2e⁻ → Ni).
Since 0.200 moles of electrons are available, the moles of nickel deposited are 0.200 / 2 = 0.100 moles.
Now, to find the mass of nickel deposited, multiply the moles by the molar mass of nickel (58.69 g/mol):
0.100 moles × 58.69 g/mol = 5.87 g
Thus, the mass of nickel deposited is 5.87 g (option B).
Learn more about electrical charge here;
https://brainly.com/question/9194793
#SPJ11
A 5.00-kg sphere is moving at a speed of 4.00 m/s. An identical sphere is at rest. The two spheres collide. The first sphere moves off at a 60.0° angle to the left of its original path. The second sphere moves off in a direction 90.0° to the right of the first sphere’s final path. Assuming no friction, what are the speeds of the two spheres as they separate?
Answer:C
Explanation:
You should just have to do the math and will get you C
An electron moving along the +x-axis enters a magnetic field. Ifthe electron experiences a magnetic deflection in the -y direction, what is the direction of the magnetic field in this region?A) along the +z-axisB) along the -z-axisC) along the -x-axisD) along the +y-axisE) along the -y-axis
The direction of the magnetic field in this region is along the -z-axis (option B).
To determine the direction of the magnetic field when an electron moving along the +x-axis experiences a magnetic deflection in the -y direction, we can use the right-hand rule.
1: Point your thumb in the direction of the electron's motion, which is along the +x-axis.
2: Point your index finger in the direction of the magnetic force experienced by the electron, which is in the -y direction.
3: Your middle finger will point in the direction of the magnetic field.
Following these steps, your middle finger will point along the -z-axis.
You can learn more about the magnetic field at: brainly.com/question/11514007
#SPJ11
if a 0.15- kg baseball with a radius of 3.7 cm is thrown with a linear speed of 48 m/s and an angular speed of 43 rad/s , how much of its kinetic energy is translational energy? assume the ball is a uniform, solid sphere.
The translational energy of the baseball is 151.88 J and the rotational energy is 0.033 J.
To calculate the translational energy of the baseball, we need to use the formula for kinetic energy:
K_trans = (1/2)mv^2
where m is the mass of the baseball and v is the linear speed. Plugging in the given values, we get:
K_trans = (1/2)(0.15 kg)(45 m/s)^2
K_trans = 151.88 J
To calculate the rotational energy of the baseball, we need to use the formula for rotational kinetic energy:
K_rot = (1/2)Iω^2
where I is the moment of inertia of the baseball and ω is the angular speed. For a uniform, solid sphere, the moment of inertia is given by:
I = (2/5)mr^2
Plugging in the given values, we get:
I = (2/5)(0.15 kg)(0.037 m)^2
I = 4.13 x 10^-5 kg*m^2
Now we can calculate the rotational energy:
K_rot = (1/2)(4.13 x 10^-5 kg*m^2)(40 rad/s)^2
K_rot = 0.033 J
Learn more about kinetic energy Refer: https://brainly.com/question/26472013
#SPJ11
Compression is to crest as rarefaction is to _________.
A. Peak
B. Trough
C. Amplitude
D. Wavelength
Compression is to crest as rarefaction is to Trough.
Hence, the correct option is B.
Because
In a longitudinal wave, compression refers to the region where the particles are closer together, while rarefaction refers to the region where the particles are farther apart.
The crest and trough, on the other hand, are terms used in transverse waves to describe the highest and lowest points of the wave, respectively. Therefore, in this analogy, rarefaction is equivalent to the trough.
Hence, the correct option is B.
To know more about Trough here
https://brainly.com/question/927657?
#SPJ4
The fusible plug that is in all chlorine containers?
a. May be used as a tap for the chlorine source
b. Should be removed after the cylinders are empty
c. Should never be removed or tampered with
d. Should be removed prior to withdrawing chlorine from the container
d. Should be removed prior to withdrawing chlorine from the container. The fusible plug is designed to melt at a specific temperature in case of a fire, releasing the pressure inside the container and preventing an explosion.
However, if the plug is still in place when chlorine is being withdrawn, it can cause the chlorine to react with the metal plug and potentially create a dangerous situation. Therefore, it is important to remove the fusible plug before withdrawing chlorine from the container. Removing or tampering with the fusible plug could lead to hazardous situations when withdrawing chlorine. Always follow proper safety guidelines and procedures when handling chlorine containers.
Learn more about chlorine here:
brainly.com/question/11026469
#SPJ11
950-kg satellite orbits the earth at a constant altitude of 90-km. (b) what is the change in the system's kinetic energy?
The change in the system's kinetic energy of the 950-kg satellite orbiting the earth at a constant altitude of 90 km is zero.
This is because the satellite is orbiting at a constant altitude, meaning its distance from the Earth's center is constant, and therefore, its potential energy remains constant. When the altitude is constant, there is no change in the system's kinetic energy, as the satellite maintains the same speed and distance from the Earth. Therefore, the change in kinetic energy is 0. Since the total energy of a satellite in orbit is constant, any change in potential energy is compensated by an equal and opposite change in kinetic energy. Therefore, since the potential energy is constant, the kinetic energy must also be constant.
Learn more about orbit here: https://brainly.com/question/18914648
#SPJ11
Question 58 Marks: 1 Shredding reduces the volume of wastes to about ______ or less of the original bulk.Choose one answer. a. 60 percent b. 50 percent c. 40 percent d. 30 percent
The answer is c. 40 percent. Shredding reduces the volume of wastes to about 40 percent or less of the original bulk.
This is because shredding breaks down the waste materials into smaller pieces, which increases the surface area and allows for more efficient packing and storage. Shredding is commonly used for paper and cardboard waste, but can also be used for other materials like plastics, textiles, and wood.
Shredding is a process that involves breaking down waste materials into smaller pieces or particles. This can be done using a variety of methods, such as cutting, tearing, or grinding. The end result is a material that has been reduced in size and volume, which can make it easier to handle, transport, and dispose of.
Shredding is commonly used for paper and cardboard waste, as these materials can take up a lot of space when they are not shredded. By shredding them, the volume of the waste can be reduced by up to 40 percent or more. This can be particularly useful for businesses or organizations that generate large amounts of paper waste, such as offices or print shops.
However, shredding can also be used for other types of waste materials, such as plastics, textiles, and wood. For example, plastic waste can be shredded into small pieces that can be melted down and recycled into new products. Textile waste can be shredded and repurposed for insulation or other materials. Wood waste can be shredded and used for fuel or as a feedstock for composting.
Overall, shredding is a useful process for reducing the volume of waste materials and making them easier to handle and dispose of. It can also help to reduce the environmental impact of waste by making it easier to recycle or repurpose.
Visit to know more about Shredding:-
brainly.com/question/30583996
#SPJ11
Question is attached as a file.
a)
The distance travelled in the first 3 seconds is 6 meters.
b.)
the total distance travelled is 13 meters.
c.)
the acceleration in the time interval from 4 seconds to 7 seconds is 0.67 m/s^2.
How do we calculate?distance = speed × time
distance = 2 m/s × 3 s = 6 meters
b)
The distance travelled in the first 3 seconds= 6 meters.
The distance travelled from 3 seconds to 7 seconds, which can be found by finding the area under the trapezium formed by the line joining (3, 2) and (7, 4), the x-axis and the vertical lines at x=3 and x=7.
The height of the trapezium is (4 - 2) m/s = 2 m/s, and the two bases are 4 s - 3 s = 1 s and 7 s - 3 s = 4 s, respectively.
the area of the trapezium is:
area = (1/2) × (1 + 4) s × 2 m/s = 7 meters
The total distance travelled is therefore:
total distance = distance travelled in the first 3 seconds + distance travelled from 3 seconds to 7 seconds
total distance = 6 meters + 7 meters = 13 meters
c)
change in speed = final speed - initial speed
At t=4 s, t speed is 2 m/s,
and at t=7 s, speed is 4 m/s.
change in speed = 4 m/s - 2 m/s = 2 m/s
The time interval is:
time interval = 7 s - 4 s = 3 s
acceleration = change in speed / time interval
acceleration = 2 m/s / 3 s = 0.67 m/s^2
Learn more about acceleration at: https://brainly.com/question/460763
#SPJ1