The x component of velocity of a particle as a function of time is shown in (Figure 1) .
Part A
Over what intervals is the work done on the particle positive?
Check all that apply.
From a to b.
From f to g.
From d to f.
From b to c.
From d to e.
From e to f.
From c to d.
Part B
Over what intervals is the work done on the particle negative?
Check all that apply.
From d to e.
From d to f.
From e to f.
From a to b.
From c to d.
From f to g.
From b to c.

Answer:

If there are more molecules present, or there's a bigger surface area on which the reaction happens, there will be more successful collisions and the reaction will go faster. Also, if the temperature is higher, more molecules will have enough energy to react, and the reaction will be faster.

The rate at which points C and D are spreading apart from each other is 10 cm / year

The magnetic stripes on the ocean floor are created by reversals of the Earth's magnetic field during the continuous formation of ocean crust at the ridge.

Mathematically, the formula for the speed of two points on the magnetic stripe is given as;

V = L / T

where;

The rate at which points C and D are spreading apart from each other is calculated as follows;

V = ( 30,000,000 cm ) / ( 3,000, 000 years )

V = 10 cm/y

Thus, the rate at which points C and D are spreading apart from each other is a function of the distance between points C and D, and the total time between the two points.

Learn more about magnetic stripe here: https://brainly.com/question/29791221

#SPJ1

The average acceleration of the bus is −6.00 m/s².

a = ? ; Δt = 1.50 s ; v1 = 9.00 m/s ; v2 = 0.00m/s

The formula to use in this case is the definition of acceleration stating that the acceleration a = Δv / Δt or a = (v2- v1) / Δt where v2 is the final velocity and v1 is the initial velocity.

Solving for the acceleration a

a = (v2- v1) / Δt

a = (0 - 9.00 m/s) / 1.50 s

a = - 9.00 m/s / 1.50 s

a = −6.00 m/s^2

The average acceleration of the bus is −6.00 m/s^2.

The complete question is,
When a bus comes to a sudden stop to avoid hitting a dog, it slows from 9.00 m/s to 0.00m/s in 1.50 seconds. What is the average acceleration of the bus?

To learn more about average acceleration refer to:

https://brainly.com/question/104491

#SPJ4

Answer:

It states that the mass of a whole object is equal to the sum of masses of its parts

Explanation:

Law of conservation of mass states that the sum of the reactants and products in a chemical reaction is the same before and after the reaction .

The answer is 6×10⁴ N/C. In the absence of matter, the energy density in a magnetic field is given by 1/2B2/0; it is expressed in joules per cubic meter.

By integrating the energy density across all of space, one may determine the entire amount of magnetic energy. We interpret uB = B2/(20) as the energy density of the magnetic field, or the amount of energy per unit volume. The amount of energy held in the coil's volume is equal to the amount of energy per unit volume held in the magnetic field multiplied by the coil's volume.

Given: B=(200T) sin [(4.010 1] gives the magnetic field in a plane electromagnetic wave.

5s (t−x/c)].

to determine the largest electric field possible and the average energy density that corresponds to the electric field.

Maximum magnetic field value: B 0 = 200 T 200* 10⁶

An electromagnetic wave travels at c speed.

Therefore, the electric field's greatest value is E 0 = cB 0.

​⟹E \s0 \s​ \s

=200×10⁻⁶ \s ×3×10⁸

⟹E \s0 \s​ \s

=6×10⁴ N/C

Learn more about energy here-

https://brainly.com/question/24284560

#SPJ4

According to the question, the Gravity Coaster travels 34 meters per second.

What is gravity?
Gravity is a natural phenomenon by which all things with mass or energy are brought toward one another. It is most commonly experienced as the force that gives weight to physical objects and causes them to fall toward the ground when dropped. Gravity is caused by the presence of mass or energy and it is the result of space-time curvature. It is the weakest of the four fundamental forces, yet it is the most dominant force in the universe, because it has infinite range and is always attractive. Gravity affects all objects in the universe, including light, and is responsible for the formation of galaxies, stars, planets and even life.

To learn more about gravity
https://brainly.com/question/940770

#SPJ1

Suppose a camera's exposure is correct when the lens has a focal length of 8.0 mm. The picture will be underexposed if the focal length is "zoomed" to 16.0 mm without changing the diameter of the lens aperture.

What does Focal length means?

Focal length is a measurement of a lens that determines how much of a scene is captured in the image. It is measured in millimeters and is calculated by the distance between the lens and the image sensor when the subject is in focus. The shorter the focal length, the wider the angle of view and the more of the scene that is captured.

What is lens aperture?

Lens aperture is the physical size of the opening in a lens that controls the amount of light that passes through the lens to the image sensor. Aperture is usually expressed in terms of f-numbers; the lower the f-number, the wider the aperture and the more light that is allowed to pass through the lens.The size of the aperture also affects the depth of field of an image, which is the range of distances within which objects appear to be in focus. A wider aperture (lower f-number) results in a shallow depth of field, while a narrower aperture (higher f-number) results in a greater depth of field.

Therfore the correct option is b. underexposed.

To know more about Focal Lenght,

https://brainly.com/question/1031772

#SPJ4

20.75g - 4 significant figures (The decimal point is included in the count, so the number of significant figures is the number of digits to the right of the decimal point plus one.)

Significant figures are the digits in a number that are meaningful in terms of accuracy or precision. They are used to express the degree of precision of a measurement. Significant figures are important in scientific calculations because they indicate the precision of the measurement. For example, if a measurement is reported as 5.00, this indicates that the measurement is accurate to two decimal places. Significant figures are also used to express the precision of a calculation. For example, if a calculation is reported as 5.00, this indicates that the calculation is accurate to two decimal places.

3400ml - 4 significant figures (The decimal point is not included in the count, so the number of significant figures is the number of digits in the number.)
9.100g - 5 significant figures (The decimal point is included in the count, so the number of significant figures is the number of digits to the right of the decimal point plus one.)

To learn more about significant figures
https://brainly.com/question/24491627
#SPJ1

If x and t represent distance and time, respectively, the C in x = (1/2)×C×t² must have the dimensions L/T²

The relationship between time (t) and distance (x) is expressed in the form x = (1/2)×C×t² in the equation x = (1/2)Ct². As a result, the constant C must have the dimensions L/T² or length divided by time squared.

This is due to the fact that the constant C must have dimensions of L/T² in order for the equation to be dimensionally balanced and for x to have the dimensions of distance (L) and t to have the dimensions of time (T).

This is so that the equation, which must have the units of L/T², the units of acceleration, can express the position of a particle traveling in a straight line with a constant acceleration, where C is the constant acceleration.

This is how the equation was analyzed in terms of dimensions. It is a means to check whether the equation is mathematically consistent.

Learn more about dimensions at

https://brainly.com/question/24313121

#SPJ4

At a spot where the film thickness is 932.5 nm,  [tex]$\lambda_1$[/tex] wavelength is missing in the transmitted light.

Wavelength  [tex]$\lambda_3{ }^{\prime}=1417.4 \mathrm{~nm}$[/tex] is strongest in transmitted light.

Index of refraction of soap film n = 0.90. The film is viewed in transmitted light.

(a) Film thickness at a spot = 932.5 nm = t

For destructive interference, we have m= order of wavelength.

n t=m [tex]$\frac{\lambda}{2}[/tex] [tex]\Rightarrow \lambda=\frac{2 n t}{m}$[/tex] where m = 1,2,3 . . .

Therefore the wavelengths that are not reflected or missing in the transmitted light satisfy

[tex]& \lambda_m=\frac{2 n t}{m} \\[/tex]

[tex]& \lambda_1=\frac{2 \times(1.90) \times\left(932.5 \times 10^{-9}\right)}{1}[/tex]

[tex]& \lambda_1=3543.5 \times 10^{-9} \mathrm{~nm} \\[/tex]

[tex]& \lambda_2=\frac{2 \times(1.90) \times\left(932.5 \times 10^{-9}\right)}{2} \\[/tex]

[tex]& \lambda_2=1771.75 \times 10^{-9}\mathrm{~nm} \\[/tex]

[tex]& \lambda_3=\frac{2 \times(1.90) \times\left(932.5 \times 10^{-9}\right)}{3} \\[/tex]

[tex]& \lambda_3=1181.1\times 10^{-9} \mathrm{~nm}[/tex]

The wavelengths [tex]$\lambda_1[/tex], [tex]\lambda_2$[/tex], and [tex]$\lambda_3$[/tex] are close to the visible region of the electromagnetic spectrum for which the destructive interference occurs,

The wavelength of visible light is in the range of 380 nm to 750 nm. So the wavelength [tex]$\lambda_1$[/tex] which falls in the infrared region is invisible [tex]$\lambda_2$[/tex] represents orange and [tex]$\lambda_3$[/tex] represents violet.

The only non-reflected colors are orange [tex]( $\left.\lambda_2\right)$[/tex] and [tex]$\lambda_3$[/tex] (violet).

(b) Wavelength's strongest in transmitted light

For constructive interference, we have

[tex]n t=\frac{\left(m+\frac{1}{2}\right)}{(\lambda / 2)}[/tex]

The wavelengths which are strongly reflected satisfy the condition

[tex]& \lambda_m^{\prime}=\frac{2 n t}{\left(m+\frac{1}{2}\right)}[/tex] where m = 0, 1, 2, 3 . . .

[tex]& \lambda_1^{\prime}=\frac{(2) \times(1.90)\left(932.5 \times 10^{-9}\right)}{\left(0+\frac{1}{2}\right)} \\[/tex]

[tex]&=\frac{1137.65}{0.5} \\[/tex]

[tex]& \lambda_1^{\prime}=7087 \times 10^{-9}\mathrm{~nm} \\[/tex]

[tex]& \lambda_2^{\prime}=\frac{(2) \times(1.90)\left(932.5 \times 10^{-9}\right)}{\left(1+\frac{1}{2}\right)} \\[/tex]

[tex]&=\frac{1137.65}{1.5} \\[/tex]

[tex]& \lambda_2^{\prime}=2362.3 \times 10^{-9}\mathrm{~nm} \\[/tex]

[tex]& \lambda_3^{\prime}=\frac{(2) \times(1.90)\left(932.5 \times 10^{-9}\right)}{\left(2+\frac{1}{2}\right)} \\[/tex]

[tex]&=\frac{1137.65}{2.5} \\[/tex]

[tex]& \lambda_3^{\prime}=1417.4 \times 10^{-9}\mathrm{~nm}[/tex]

According to the visible spectrum, the wavelength range is 380 nm to 750 nm. In the above case only [tex]$\lambda_3^{\prime}=1417.4 \mathrm{~nm}$[/tex] is visible which is blue. So only blue is non-reflective color. The other two wavelengths have transmitted light which is in the infrared region. [tex]\left(\lambda_{+}^{\prime}\right.$[/tex] and [tex]$\left.\lambda_2^{\prime}\right)$[/tex]

The only strong reflection occurs at [tex]$\lambda_3{ }^{\prime}=1417.4 \mathrm{~nm}$[/tex] which corresponds to the blue region.

Therefore the soap film possesses a pronounced blue color.

For more questions on wavelengths

https://brainly.com/question/10095777

#SPJ4

A soap film has an index of refraction n = 1.90. The film is viewed in transmitted light.

(a) At a spot where the film thickness is 932.5 nm, which wavelengths are missing in the transmitted light?

(b) Which wavelengths are strongest in transmitted light?

In the given image gravitational potential energy is being transferred to kinetic energy. I n this case, option D is correct.

How does energy transform?

The process of changing energy's form, also known as energy transformation or energy conversion, is called this.

A quantity that allows one to move objects, perform work, or produce heat is referred to as energy in physics.

According to the principle of energy conservation, energy can change forms and be transferred to different locations or things, but it cannot be created or destroyed.

Energy can be used in many different ways, such as to power mechanical work so that machines can be operated, to support natural processes, or to benefit society in other ways, such as by providing for needs such as heating, cooling, lighting, or other societal requirements.

To Learn more About Energy transformation refer To:

brainly.com/question/24590200

#SPJ1

Newton’s first law explains why roller coasters option C. need constant pulling to stay moving.

Newton's first law states that an object at rest will remain at rest and an object in motion will remain in motion with the same speed and in the same direction unless it is acted upon by an external force.

Therefore, for a roller coasters to keep moving there should be a constant pulling to stay moving. It could be concluded that the correct answer is as given above.

learn more about Newton's first law: https://brainly.com/question/10454047

#SPJ1

List these drinks in order of kinetic energy, starting with the drink whose particles have the highest kinetic energy:

hot chocolate > juice > milk > water.

The average kinetic energy of the particles in an object is measured by its temperature. The velocity of these particles likewise increases as the temperature rises.

A thermometer or a calorimeter is used to determine the temperature. In other words, a system's internal energy is determined by its temperature.

Hence, the kinetic energy of molecules is proportional to temperature of the liquid. So, list these drinks in order of kinetic energy:

hot chocolate > juice > milk > water.

Learn more about temperature here:

https://brainly.com/question/11464844

#SPJ1

True. In a head-on collision between two protons, the total momentum of the system must remain the same.

Total momentum is the sum of the momentum of all the objects in a system. Momentum is a vector quantity, meaning it has both magnitude and direction. It is calculated by multiplying the mass of an object by its velocity. In a closed system, the total momentum of the system remains constant, meaning that the momentum of one object increases as the momentum of another decreases. This is known as the law of conservation of momentum. This law states that the total momentum of a system before and after a collision is the same.

Since most of the resultant particles travel to the right, there must be at least one particle that moves to the left in order to conserve the momentum of the system.

To learn more about total momentum
https://brainly.com/question/25121535
#SPJ1

You need to survive from extreme cold and extreme hot temperature, low air pressure with difficulty in breathing and no medium of sound travel, when you are in  thermosphere.

All life on Earth is shielded by the atmosphere, which is made up of gases that regulate temperature and reflect harmful solar rays. It shields living things from the sun's harmful rays.

From 80 to 400 km are in the thermosphere r above the mesopause. The earth's radio waves are reflected by this stratum. In this layer, as you ascend, the temperature begins to increase once more.

Learn more about atmosphere here:

https://brainly.com/question/26767532

#SPJ1

The fraction of the radioactive nuclei that would remain after 80 days is  1/16.

The faction of the original radioactive nuclei that would remain after 80 days is calculated as follows;

0 day --------------------> N

20 days ----------------> N/2

40 days -----------------> N/4

60 days ------------------> N/8

80 days ------------------> N/16

Thus, the fraction of the radioactive nuclei that would remain after 80 days is a function of the half life and the initial mass of the nuclei.

Learn more about half life here: https://brainly.com/question/2320811

#SPJ1

Answer:

9.9 m/s

Explanation:

All of the PE  (mgh) will be cnverted to KE ( 1/2 m v^2)

mgh = 1/2 m v^2

gh = 1/2 v^2

v = sqrt (2 gh)         Note that the mass of the book is not needed !

v = sqrt ( 2 * 9.81 m/s^2 * 5) = 9.9 m/s

The field points in the positive x direction and under the influence of the field the proton moves 0.25 meters in that direction are listed below.

What is proton?

With a negative charge, electrons are a particular subatomic particle type. Positively charged subatomic particles called protons fall into this category. The strong nuclear force is responsible for the protons' interconnection in an atom's nucleus. Subatomic particles without charge include neutrons (they are neutral).

What is magnitude?

It displays the motion of an object in motion, including any absolute, relative, or specific sized movements. It can be used to define the size or scope of anything. In physics, the general term "magnitude" is used to describe size or distance.

a, The electric field potential are high to the displacement.

c, The 2.5m/s of the proton after it has moved 0.25 meters, beginning from rest.

Therefore,  field points in the positive x direction and under the influence of the field the proton moves 0.25 meters in that direction are listed below.

Learn more about proton from the given link.

https://brainly.com/question/17351413

#SPJ1

A. The reaction given is PbCO3(s) ⇌ PbO(s) + CO2(g) which is at equilibrium at 410 ∘C.

The equilibrium constant (Kp) for this reaction at that temperature can be found using the data in Appendix C of the textbook.

The value of Kp at 410 ∘C is 1.0 x 10^-5.

To calculate the equilibrium pressure of CO2 in the system at 410 ∘C, we use the following equation:

Kp = [CO2]^(coefficient of CO2 in the balanced equation)

[PbO][CO2]^1 = 1.0 x 10^-5

Since the coefficient of CO2 in the balanced equation is 1, we can substitute the value of Kp into the equation as:

[CO2] = √(Kp) = √(1.0 x 10^-5) = 1.0 x 10^-2.5 = 3.162 x 10^-3

The equilibrium pressure of CO2 in the system at 410 ∘C is 3.162 x 10^-3 atm.

B. For equilibrium pressure of CO2 in the system at 240 ∘C, we can use the Kp value at that temperature which is 1.5 x 10^-7 from the Appendix C.

[CO2] = √(Kp) = √(1.5 x 10^-7) = 1.5 x 10^-3.5 = 2.121 x 10^-4

The equilibrium pressure of CO2 in the system at 240 ∘C is 2.121 x 10^-4 atm.

It should be noted that the values of Kp, pressure and temperature are interrelated in the equilibrium constant equation.

As the temperature decreases, the pressure of CO2 decreases as well.

To know more about equilibrium pressure refer to:

brainly.com/question/30115703

#SPJ4

The net force on the block is not zero since the only force acting on it is gravity. The net force on the incline is always zero since no forces are acting on it. The net force on the block-incline system is always zero since the force of gravity and the normal force of the incline are equal and opposite. The momentum of the block is conserved since it is an isolated system, but the momentum of the incline is not conserved since it is not an isolated system. The momentum of the block-incline system is conserved since no external forces are acting on it.

i. No, the net force on the block is not always zero. Since the block is at rest and the incline is frictionless, the only force acting on the block is gravity, so the net force on the block is not zero.

ii. Yes, the net force on the incline is always zero. Since the incline is not moving and is fixed in place on the table, there are no forces acting on the incline, so the net force on the incline is zero.

iii. Yes, the net force on the block-incline system is always zero. As the block slides down the incline, the force of gravity acts on the block and the normal force of the incline acts on the block. These two forces are equal and opposite, so the net force on the system is zero.

iv. Yes, the momentum of the block is conserved. Momentum is conserved in an isolated system, and the block is an isolated system since no external forces are acting on it.

v. No, the momentum of the incline is not conserved. The incline is not an isolated system since the force of gravity is acting on it. Therefore, the momentum of the incline is not conserved.

vi. Yes, the momentum of the block-incline system is conserved. Since no external forces are acting on the system, the total momentum of the system is conserved.

The net force on the block is not zero since the only force acting on it is gravity. The net force on the incline is always zero since no forces are acting on it. The net force on the block-incline system is always zero since the force of gravity and the normal force of the incline are equal and opposite. The momentum of the block is conserved since it is an isolated system, but the momentum of the incline is not conserved since it is not an isolated system. The momentum of the block-incline system is conserved since no external forces are acting on it.

learn more about force here

https://brainly.com/question/13191643

#SPJ4

Option A is correct. The electronic exchange of business information using a standardized format is known as electronic data interchange (EDI).

a method that enables electronic information transfer between businesses rather than paper-based communication. Trading partners are companies that conduct commerce electronically. The computer-to-computer transmission of common business documents including invoices, bills of lading, shipment schedules, and purchase orders is made possible through an electronic data interchange (EDI). The automatic, computer-to-computer transmission of common electronic business documents between business partners through a standardized, secure connection is known as electronic data interchange (EDI). The electronic exchange of business information using a standardized format is known as electronic data interchange (EDI).

Learn more about transmission here-

https://brainly.com/question/14616720

#SPJ4

( a ) The magnitude of the impulse given to the meteor is 2,480,000 kg.m/s at 22⁰ from original position.

( b ) The magnitude of the force applied to the meteor is 55,111.1 N.

The magnitude of the impulse given to the meteor is calculated from the change in momentum of the meteor.

Mathematically, the formula for Impulse is given as;

J = ΔP

J = m (vf - vi )

where;

The magnitude of the impulse given to the meteor is calculated as follows;

J = ( 310, 000 kg ) ( 27 m/s - 35 m/s )

J = ( 310, 000 kg ) ( -8 m/s )

J = -2,480,000 kg.m/s

| J | = 2,480,000 kg.m/s

The magnitude of the force applied to the meteor is calculated as follows;

F = ma = J / t

where;

F = ( 2,480,000 kg.m/s ) / ( 45 s )

F = 55,111.1 N

Learn more about impulse here: https://brainly.com/question/25700778

#SPJ1

The factor that would shift the supply curve of the icecream to the right is D) Both A and C.

The ice cream freezer must aerate and freeze the mixture to create the ice cream's characteristic texture. Most commercial ice cream freezers work in a similar fashion. The mixture is pumped into a metal drum surrounded by a very cold refrigerant. This is one of the new technology for icecream. At the same time, a stream of air is introduced into the barrel. Taste variation and consumer convenience are the main factors behind the global demand for frozen dessert products. Additionally, increasing disposable income and the introduction of various products into the dessert category to cater to the choices of many consumer groups are driving the ice cream market.

Learn more about the supply curve in

https://brainly.com/question/1915798

#SPJ4

Your meal will warm up in around 15 minutes because to the heat generated by this interaction. Heat is progressively released from it. However, this reaction happens considerably more quickly in a FRH, and as a result, heat is released much more quickly.

An oxidation-reduction reaction, an electron-transfer mechanism, is how ration heaters produce heat. Magnesium metal oxidises in water.

The ingredients used to make the FRHs include food-grade iron, magnesium, and sodium powder. Each FRH is packaged separately in a strong, leak-proof polybag that also acts as the MRE's heating container.

Learn more about FRH here:

https://brainly.com/question/16557710

#SPJ1

The y component of the velocity for the segment BC in the bacterium's trajectory is 8.7 μm/s, calculated by using the equation UBCy = UBCcos(θ).

The y component of the velocity for the segment BC in the bacterium's trajectory can be calculated by using the following equation:

UBCy = UBCcos(θ)

Where UBC is the magnitude of the velocity of the segment BC and θ is the angle of the segment BC.

In this problem, UBC is 10 μm/s and θ is 40°.

Therefore, the y component of the velocity for the segment BC in the bacterium's trajectory is 8.7 μm/s.

The y component of the velocity for the segment BC in the bacterium's trajectory is 8.7 μm/s, calculated by using the equation UBCy = UBCcos(θ).

learn more about velocity here

https://brainly.com/question/18084516

#SPJ4

The value of resistor R in the circuit shown in the figure is 19.7 ohm.

A two-terminal passive electrical component used in electrical circuits to limit or regulate the flow of current. A resistor's primary function is to lower the voltage and reduce current flow in a specific area of the circuit.

current I = 0.92 A

The voltage V=> IR

                  V=> 0.92 x 10 = 9.2V (from figure)

current around resistor R = 2 - (0.92 + (9.2/15)) (from figure)

the resistor R = V/I

                     = 9.2 / 0.467 = 19.7 ohm.

The term "electric current" describes both the direction and volume of electricity flowing across a circuit in an electrical device. Amperes are used to measure it (A).

Learn more about resistor here:

brainly.com/question/24297401

#SPJ4

Answer:

Explanation:

To find the speed of the clock at the lowest point in its swing, we can use the formula:

Speed = (distance) / (time)

In this case, the distance is the length of the clock (0.993 m) multiplied by the sine of the maximum angle of the swing (4.57°).

Speed = (0.993 m) x (sin 4.57°)

But we need to keep in mind that the angle needs to be converted to radians before we can use it in the sin function, since the trigonometric functions operate in radians.

So, the first step is to convert the angle from degrees to radians:

4.57° * (π/180) = 0.0799 radians

Now we can plug that angle in the formula,

Speed = (0.993 m) x (sin 0.0799 radians)

This will give us the speed of the clock at the lowest point of its swing.

The pendulum on grandfather clock is 0.993 m long, and swings to maximum 4.57° angle. It is moving at 0.248 m/s, the lowest point in its swing.

A pendulum is a weight suspended from pivot such that it can swing freely. When the pendulum is displaced sideways from its resting position, equilibrium position, then it is subject to a restoring force due to gravity that will accelerate it back towards equilibrium position.

As, m⋅ g⋅ sin(θ)=mv²/(R⋅sinθ)

So, v² = gr sin²Ф

= 9.8 * 0.993 * sin (4.57)

Hence, v= 0.248 m/s

It is moving at 0.248 m/s the lowest point in its swing.

To know more about pendulum, refer

https://brainly.com/question/26449711

#SPJ1

Answer of all the questions about boyle's Law is given below.

Boyle's Law is an important gas law named after Robert Boyle, an Irish physicist and chemist. It states that the pressure and volume of a gas are inversely proportional. This means that when the pressure of a gas increases, its volume decreases, and vice versa. This law is applicable to many real-life situations, such as the effect of altitude on atmospheric pressure and the behavior of gases in a closed system.

(a) The rate of change of volume with respect to pressure can be calculated using the derivative of Boyle's Law. The equation is dV/dP = -C/P2, where C is the constant of the equation.

(b) The volume of the gas is decreasing more rapidly at the beginning of the 10 minutes, as the pressure is much lower. As the pressure increases, the rate of decrease for the volume will become slower, as the pressure and volume are inversely related.

(c) To prove that the isothermal compressibility is given by B=1/P, we can start with the definition of isothermal compressibility: B=–dV/dP(V,T). Using Boyle's Law and the derivative of Boyle's Law, we can substitute the equation to get B=–(C/P2). Rearranging the equation, we get B=1/P. Therefore, the isothermal compressibility is given by B=1/P.

To know more about Boyle's Law click-
https://brainly.com/question/24938688
#SPJ4